Related Manuals for Granberg Diagonal lift 504-055
Summary of Contents for Granberg Diagonal lift 504-055
- Page 1 English Diagonal lift Diago 504 Doc. No: M504 Edition: 10 Date: 2017-06-19 INSTRUCTION MANUAL Diagonal lift 504...
- Page 2 For mer information, see: www.granberg.se...
-
Page 3: Table Of Contents
Content Section: Headline: Page: Introduction ..............................4 Declaration of Conformity ........................4 Intended use - Technical data ........................ 4 Installation instructions: Mechanical construction ........................5 Delivery modules ............................5 Pre-assembly of the lift mechanism ....................6 Joist heights ..............................7 Location wall socket and control devices ..................8 Location wall socket for lighting ......................9 To consider before installation ......................9 Installation on a wall .......................... -
Page 4: Introduction
Introduction We have the pleasure to deliver a Granberg Interior wall cabinet lift series Diago 504. This is an electrically operated lifting and lowering system for installation of new or existing wall cabinets. It can be used separately, or together with the Granberg work top units, and it becomes then a total adaptation of the kitchen. -
Page 5: Mechanical Construction
Mechanical construction The diagonal lift Diago 504 comprises a wall frame, to be installed on a wall, a cabinet frame onto which one or more cabinets are installed, and four link arms that operate in parallel. The arc-shaped lift and lowering path is achieved by an electrically pow- ered screw jack, which operates between the wall and cabinet frames. -
Page 6: Pre-Assembly Of The Lift Mechanism
Pre-assembly of the lift mechanism Picture 1 4.3.1 Install the bottom plate (A) onto which the cabinet shall be mounted. The plate is hung on the frame, and then locked with the M5x45 screws (B). (Do not forget the washer). NOTE! It is very important that the locking screws (B) are installed... -
Page 7: Joist Heights
Joist heights for the wall cabinet lift Laying joists shall be placed according to the dimensions below: A = 1485 mm from floor to centre of the joist B = 2075 mm from floor to centre of the joist... -
Page 8: Location Wall Socket And Control Devices
Location of sockets and control devices The wall cabinet lift shall be connected to a separate main switch, which is placed in the kitchen or its vicinity. The location of a socket for 230 V, 50 Hz / 120 V, 60 Hz (depends on model) should be coordinated with other equipment in the kitchen. The wall cabinet lift is often in combined with a worktop system. -
Page 9: Location Wall Socket For Lighting
Check that the trip panel and the light ramp strip really cover the underside of the cover panel, so that there is no trip risk. Aligning of adjacent cabinets: Adjacent cabinets should be brought forward to be aligned with the cabinets on the lift. Granberg can offer extension parts for this purpose. -
Page 10: Installation On A Wall
Installation on a wall Picture 1 4.8.1 Start by installing the fixed cabinets besides the lift cabinet. The space shall be 10 - 15 mm wider than the cabinet to be placed on the lift. 4.8.2 Connect the cable to the UP/DOWN control unit acc. picture. 1. 4.8.3 Run the lift to the position shown in picture 2. -
Page 11: Installation Of Cabinet On Lift Mechanism
4.9.7 Adjust when necessary the two adjustment screws on the Picture 1 underside of the bottom plate (A). See pos. (B), picture 1. NOTE! After adjustment, lock the screws acc. pos. (C), picture 1. Picture 2 4.10 Install the cabinet / cabinets on the lift 5-8 mm 4.10.1 Lower the lift and push up the top plate. -
Page 12: Installation Of Light Ramp (Accessory)
Picture 4 trip plate. Use the included screw. See picture 5. 4.13.4 Fasten the cable with the included tension reliever. See pos. (C), picture 5. NOTE! Only the Granberg original lighting grants full safety. Picture 5 4.14 Functional test After installation a complete functional test with full load shall be made: Run the cabinet lift down and up all the way to respectively end position. -
Page 13: Safe Use
• Competent persons only must carry out installation, service and repair works. • Only Granberg original spare parts shall be used when replacing any parts. Our warranty commitment can otherwise be invalidated. -
Page 14: Safety Arrangements
Further to the incorporated safety arrangements additional can safety actions may be required on or at the Diagonal lift. Dis- cuss suitable actions with your Granberg representative or with the health and safety inspection. We recommend that a Risk assessment in accordance with the Machinery Directive shall be made for the actual working con- ditions. -
Page 15: Alternative Control Devices
Alternative control devices The operator shall have a clear view of the hazardous parts of the Diagonal lift and its motions, but not directly within the work area, as there is a risk that objects may fall out of the cabinet. (Due to limited space it can be necessary to place the control devices is placed within the work area). -
Page 16: Maintenance
When the Diagonal lift unit shall be re-used shall it must be cleaned, inspected and go through a full operation test before it is installed on the new site. We recommend the machine to be sent to Granberg or to the Granberg distributor to get this done. The machine is manufactured from re-usable materials or from materials that can be recycled. -
Page 17: Warranty
Damages caused by misuse or incorrect operation of the equipment means that the warranty would expire. Before any warranty work is commenced by a customer Granberg must be contacted for analysis and approval. We do not ac- cept to carry any warranty costs if the repair work has started without an agreement by us. -
Page 18: Fault Finding
(See section 4.14) Spare parts list If any component does not work or has broken, contact your supplier. Only Granberg original spare parts must be used when replacing any parts. Our warranty commitment may otherwise be invalidated. -
Page 19: El. System / Electric Circuit Diagram
The text “TOP OBEN” shall be turned upside down Safety trip panel when the control box is installed. CE-Declaration of conformity (According Machinery Directive 2006/42/EG, Annexe 2A) Manufacturer: Granberg Interior AB Tel. +46-11-19 77 50 Box 6112, SE-600 06 NORRKÖPING, Sweden declares under sole responsibility that the product:... - Page 20 Granberg Interior AB Box 6112 600 06, Norrköping, Sweden Tel: +46(0)11-19 77 50 E-mail: info@granberg.se Internet: www.granberg.se...