Logan 650-1 Instruction Manual
  1. Manuals
  2. Brands
  3. Logan Manuals
  4. Cutter
  5. 650-1
  6. Instruction manual

Logan 650-1 Instruction Manual

Framer’s edge elite mat cutter
Hide thumbs

Advertisement

Table of Contents

INSTRUCTION MANUAL
FRAMER'S EDGE ELITE
MAT CUTTER
MAT CUTTING BLADES ARE SHARP
LoganGraphic.com
Professional Series mat cutting system with laminate board surface,
CAUTION!!
MODEL 650-1 / 655-1 / 660-1
INSTRUCTIONS AND OPERATION MANUAL
ball bearing guided cutting head, production stops, 9" & 32"
squaring arms, plus dual straight & bevel cutting heads
Model 650-1 Framer's Edge Elite - 40" mat cutter
Model 655-1 Framer's Edge Elite - 48" mat cutter
Model 660-1 Framer's Edge Elite - 60" mat cutter
ID Number (on bottom of board)
Date (on bottom of board)
For best results use only
authentic Logan blades
Uses Logan Replacement
Blade #269 Blade #268
Purchase Date
L618DN4 Rev.3 1-16

Advertisement

Table of Contents
loading

Related Manuals for Logan 650-1

Summary of Contents for Logan 650-1

  • Page 1 9” & 32” squaring arms, plus dual straight & bevel cutting heads Model 650-1 Framer’s Edge Elite - 40” mat cutter Model 655-1 Framer’s Edge Elite - 48” mat cutter Model 660-1 Framer’s Edge Elite - 60” mat cutter...

  • Page 2: Carton Contents

    Congratulations on your purchase of the Logan Professional Series, Framer’s Edge Elite Mat Cutter. The Framer’s Edge Elite Mat Cutter is a well-designed mat cutter, combining the best of what Logan mat cutters have to offer. It’s designed specifically with the framer in mind.

  • Page 3: Identification Of Machine Components

    Knob adjusts to 3 blade holders Depth Adjustment Screw depth settings blade in head Adjustment screw used to set bevel cutting head to cut various thickness matboard. Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...

  • Page 4: Straight Blade Installation

    Mat Guide Assembly Press each Mat Guide Channel into board slots with rounded end towards guiderail. Insert channel screw from the UNDERSIDE of board and tighten with Logan screwdriver. (Fig. 8) Loosen each mat guide knob three full turns. Hold mat guide at ends with your thumbs on the loosened knobs with raised edge facing guiderail and evenly drop mat guide into channels.
  • Page 5 (Fig. 18) NOTE: It is dangerous to leave the blade set in the “cut” position. Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 18 Fig. 17 Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...
  • Page 6 10. Continue steps 5 through 8 until all four sides are cut. Fig. 21 Fig. 22 Fig. 23 Fig. 24 Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...
  • Page 7 10. Continue steps 6 through 9 until all four sides are cut. Fig. 28 Fig. 29 Fig. 27 Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...

  • Page 8: Bearing Adjustment

    (Fig. 32) Test tip, readjust if necessary. Fig. 32b Test wobble and readjust until wobble is eliminated and sliding motion is smooth. Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...
  • Page 9 This screw will fine tune the BOTTOM over/under cut only when using the production stop. To adjust, use Logan screwdriver to turn screw in (clockwise) to increase overcut or turn screw out (counterclockwise) to decrease overcut. (Fig. 33) Top Overcut Adjustment Loosen knob to allow leg to slide.

  • Page 10: Re-Squaring The Squaring Arm

    Re-install the squaring arm and check for square. This is a trial and error method. In some cases more than a quarter turn is needed, in some cases, less. Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...
  • Page 11 5. Re-tighten the Black Knobs first. 6. Then re-tighten the four screws. Do another parallel test to ensure that the Mat Guide is now parallel. Logan Graphic Products Inc., 1100 Brown St, Wauconda, IL 60084 847-526-5515 cs@logangraphic.com LoganGraphic.com...

  • Page 12: Troubleshooting

    Cutting a Border Less Than 3/4” - Mark mat (back side) using a pencil and do not use Mat Guide. Blade Life - Use only authentic Logan blades to ensure best results. No two blades last the same amount of time. Size of mats and differences in mat board effect blade life.

This manual is also suitable for:

655-1660-1

Table of Contents