Hilti GX 2 Manual
Generation: 01
Hide thumbs
Also See for GX 2:
- Manual (304 pages) ,
- Original operating instructions (290 pages) ,
- User manual (71 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Hilti GX 2
Summary of Contents for Hilti GX 2
- Page 1 GX 2 English Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...
- Page 2 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...
-
Page 3: Table Of Contents
Contents Information about the documentation ........About this documentation . -
Page 4: Information About The Documentation
Remedying possible malfunctions ........Removing foreign objects from the area of the fastener guide . -
Page 5: Highlighting Of Designations And Markings
Markings on the fastening tool 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. - Page 6 In order to ensure faultless operation of the fastening tool, all parts must be fitted correctly and must meet the necessary requirements. Damaged protective devices or other parts must be properly repaired or replaced by Hilti Service unless otherwise stated in the operating instructions.
- Page 7 ▶ A battery that is too hot to hold may be defective. Allow the battery to cool down in a place where there is no risk of causing a fire. Check that there are no flammable materials nearby. Contact Hilti Service.
- Page 8 English Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...
- Page 9 English Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...
-
Page 10: Description
3 Description 3.1 Overview of the product English Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01... -
Page 11: Intended Use
▶ Use only Hilti battery chargers of the C 4/12-50 series for charging these batteries. 3.3 Items supplied Gas-actuated fastening tool with fastener guide, 2 batteries, charger, toolbox and operating instructions. You can find other system products approved for your product at your local Hilti Center or online at: www.hilti.com 3.4 Fastener guide The fastener guide holds the studs or, respectively, guides the nails and, when the tool is actuated, thus directs the fasteners into the supporting material at the desired position. -
Page 12: Gas Can
Status Meaning Position 1 • Position for attaching to a waist belt Position 2 • Position for attaching to ladders, scaffolds, platforms, etc. Position 3 • Belt hook removed 3.9 Gas can Note Observe the safety instructions provided with the gas can! In order to operate the fastening tool, the gas can must be inserted in the gas can compartment. -
Page 13: Noise Information And Vibration Values
Fastener diameter • 2.6 mm • 3.0 mm Compression stroke 20 mm Magazine capacity in strips of 10 nails (Magazine capac- 1 …4 ity) Maximum fastener driving frequency (Fasteners per hour) 1,200 4.2 Noise information and vibration values The sound pressure and vibration values given in these instructions have been measured in accordance with a standardized test and may be used to compare one fastening tool with another. -
Page 14: Inserting The Battery
5.4 Inserting the battery 1. Check that the contacts on the battery and on the fastening tool are undamaged and free from foreign objects. 2. Fit the battery and make sure that it is heard to engage. ◁ Once the battery has been fitted, the charge status LEDs light for a short time. CAUTION A falling battery presents a hazard. -
Page 15: Optional Operating Steps
8 Optional operating steps 8.1 Removing the transport safety device from a new gas can 1. Lift the transport safety device, containing the metering valve, away from the gas can. 2. Remove the metering valve from the transport safety device. 3. -
Page 16: Removing The Fastener Guide
WARNING Risk of finger injury! Fingers could be pinched when the nail pusher is released. ▶ When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward slowly as far as it will go. 5. - Page 17 10.3 Maintenance ▶ To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com.
- Page 18 Malfunction Possible cause Action to be taken The fastener guide is not held per- ▶ Press the nose of the tool pendicular to the working surface. against the working surface, keeping the fastener guide perpendicular to the surface (see driving nails, → page 12). Fasteners break.
- Page 19 Malfunction Possible cause Action to be taken No fastener is driven. Inadequate number of nails in the ▶ Load the magazine. → page 11 magazine. Nail transport malfunction. ▶ Check the nail strip and, if damaged, use a new one. ▶...
- Page 20 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
- Page 21 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...
- Page 22 Hilti = registered trademark of Hilti Corp., Schaan 20170210 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 00 Printed: 07.09.2017 | Doc-Nr: PUB / 5336049 / 000 / 01...