SPECIFICATIONS <Tuner section> <General> Frequency range FM: 87.5 MHz to 108.0 MHz Speaker 80 mm cone type (2) Antenna: Rod antenna Outputs Headphones jack: stereo mini-jack Power output 2.5 W + 2.5 W 530 kHz to 1,710 kHz (EIAJ 7 ohms, T.H.D. 10 %) Antenna: Ferrite bar antenna 1.9 W + 1.9 W (DIN 1% Rated Power)
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor Chip resistor Dimensions (mm) Wattage Type Tolerance Symbol Resistor Code Form 1/16W 1005 0.35 1/16W 1608 0.45 1/10W 2125 1.25 0.45 1/8W 3216 0.55 TRANSISTOR ILLUSTRATION E C B E C B E C B...
Page 18
IC DESCRIPTION IC, LC78622ED Description Pin No. Pin Name DEFI Defect detection signal (DEF) input. ("L" is applied when not used.) For PLL/Test input. A pull-down resistor is incorporated. Phase comparison output to control the external VCO. VVSS – Ground of the built-in VCO. Normally, 0V. ISET For the connection of a resistor which adjusts the PDO output current.
Page 20
IC, LA9241ML Description Pin No. Pin Name For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 21
Pin No. Pin Name Description The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror. SLOF Sled servo off control input. CV– CLV error signal input from the DSP. RFSM RF output.
Page 22
IC, LC865516A-5P16 Pin No. Pin Name Description SEG E SEG E control. SEG F SEG F control. SEG G SEG G control. — Not connected. I-RST Microprocessor reset input. XT1 (IN) Connected to an external 32.768 kHz crystal oscillator. — Not connected.
Page 23
Pin No. Pin Name Description — Not connected. SEG DP SEG DP control. SEG A SEG A control. SEG B SEG B control. SEG C SEG C control. SEG D SEG D control. — Not connected. – 23 –...
ADJUSTMENT <TUNER / DECK / CD> < RADIO SECTION > < CD SECTION > 1. Focus Bias Adjustment 1. AM Frequency Range Adjustment • Test Point: TP5 (LCH), TP6 (RCH) Make the focus bias adjustment when replacing and repairing • Adjustment location: L006, TC003 the optical block.
CD MECHANISM PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION 1 S2-121-A28-400 COVER GEAR 2 S2-511-A21-000 GEAR MIDDLE 3 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 B 87-261-073-410 SCR S-TPG FLT 2.6-6 ALL M8-ZZK-E90-070 DA11T3C ACCESSORIES / PACKAGE LIST REF.
Page 31
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9420208 0251431 Printed in Singapore...