Subscribe to Our Youtube Channel
Related Manuals for J-Tech Digital JTECH-HD4X48
Summary of Contents for J-Tech Digital JTECH-HD4X48
- Page 1 4×4HDMI Matrix With 4 Cat 5e/6 Extender Outputs, Bi-Direction IR&Power over UTP...
- Page 3 SAFETY AND NOTICE 4×4HDMI Matrix With 4 Cat 5e/6 Extender Outputs, Bi-Direction IR&Power over UTP,has been tested for conformity to safety regulations and requirements, and been certified for international use . however, like all electronic equipment ,the JTD-ID:287 should be used with care. please read and follow the safety instruction to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Page 4 INTRODUCTION Product model and standard: HDMI 4x4 single Cat5e/6 extender output HD video matrix, which can accept 4 HD HDMI signal inputs, as well 4 HD HDMI and 4 Cat5e/6 RJ45 outputs can select any one of 4 video inputs. This 4x4 matrix can support maximum 1080p 3D or 1080p 60fs resolution, and also include a 4x4 dual direction IR matrix companion with video matrix extender output.
- Page 5 APPLICATION...
- Page 6 SPECIFICATION&PACKAGE CONTENTS 4 HDMI input ports(female type A); 4 HDMI outputs (female type A);4 CAT5e/6 extender Interface outputs (RJ45); 4 IR outputs (3.5mm);4 IR inputs (3.5mm);RS232 series port(DB9); LAN port (RJ45); 12V DC in (Ø3) Power consumption < 24 W when the function of power over UTP of 4 extender outputs are on. Dimension (L x W x H): 338 .
- Page 7 PRODUCT INTRODUCTION Input ports and output ports: INPUTSTATUS INPUTSTATUS INPUTSTATUS INPUTSTATUS ON/OFF UTPOUTPUTSTATUS HDMIOUTPUTSTATUS OUTPUT B OUTPUT A OUTPUT C OUTPUT D POWER CONFIG IRINPUT IROUTPUT MadeInChina RS232 DC12V HDMIOUTD UTPOUTD UTPOUTC HDMIOUTC HDMIIN4 HDMIIN3 HDMIIN2 HDMIIN1 HDMIOUTB UTPOUTB UTPOUTA HDMIOUTA 1) Local IR receiver window 2)UTP extenderreceiverlinkstatus...
- Page 8 Typical installation instruction...
-
Page 9: Operation Instruction
OPERATION INSTRUCTION HDMI 4×4 Matrix: The product has 4 HDMI input, and 4 HDMI/UTP output, and all HDMI ports support HDMI 1.3 standard. 4 HDMI/UTP outputs can select any one of 4 HDMI different inputs, or same HDMI inputs. The user can control 4x4 matrix by front panel button, local IR remote, RS232 or local 100M LAN Ethernet port. - Page 10 OPERATION INSTRUCTION...
- Page 11 OPERATION INSTRUCTION “Local IR matrix”means IR transmission path is between local IR IN and OUT which is located in matrix’s IR IN/OUT socket. HDMISource HDMISource HDMISource HDMISource 3 2 1 4 LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL...
- Page 12 OPERATION INSTRUCTION SWITCH OFF(Default) NUMBER Choose the lower definition display terminal’s Choose the higher definition display terminal’s EDID forward to source EDID forward to source Power over UTP function is OF F Power over UTP function is ON EDID dynamic selection will be done only EDID dynamic selection will be done only with two sinks connected to same source Local IR matrix is ON;...
- Page 13 OPERATION INSTRUCTION The 4x4 matrix has internal EDID function ,support HDMI display terminal, EDID dynamic selection when each 2 HDMI display terminals choose the same HDMI source. There are EDID dynamic selection when each 2 HDMI display terminals choose the same HDMI source. There are two different EDID dynamic selection modes, one is to choosethe lower definition EDID as current EDID, two different EDID dynamic selection modes, one is to choosethe lower definition EDID as current EDID, and the other is to choose the higher definition EDID as current EDID.
- Page 14 OPERATION INSTRUCTION which can make sure UTP extender receivers get the power from the UTP output ports without DC adapters. Please note that UTP extender receivers must also support power over UTP and get the matched UTP extender receiver model for this function.This power over UTP function should be turned on when set “CONFIG”...
-
Page 15: Operation Instruction
OPERATION INSTRUCTION T5eorCAT6 Ethernet cables, TIA/EIA-568B, refer to below pin definition. Storage conditions Products storage temperature should be -20°C~60°C. For long time storage requirement, please use original carbon boxes, and avoid from high humid, acid base or dusty place. Maintenance... -
Page 16: Trouble Shooting
TROUBLE SHOOTING... -
Page 17: Appendix-A Gui User Guid
APPENDIX-A GUI USER GUIDE Input Selection and Mapping 1) I/O: Select the input Click“Send”to change the I/O setting 2)Save Mapping: Select Mapping(1-8) 3)Preset mapping: Select Mapping(1-8) Click“Send”buttontorecallpreviousmappingwhicharesaved... - Page 18 APPENDIX-A GUI USER GUIDE Rename I/O Button 1) Rename I/O: Rename output name Rename input name 2) Rename Mapping: Rename Mapping name...
- Page 19 APPENDIX-A GUI USER GUIDE...
- Page 20 APPENDIX-A GUI USER GUIDE EDID Button Clik"View/Create"button,display"EDID Analysis" popup menu...
- Page 21 APPENDIX-A GUI USER GUIDE NETWORK...
- Page 22 APPENDIX-A GUI USER GUIDE...
- Page 23 APPENDIX-A GUI USER GUIDE...
- Page 24 APPENDIX-A GUI USER GUIDE 6) When matrix is power on, Update is working; Progress bar will show the update progress; Status bar will show “Update successfully” once update is completed...
- Page 25 APPENDIX-A GUI USER GUIDE...
-
Page 26: Appendix-A Gui User Guid
APPENDIX-A GUI USER GUIDE Click button to change connection status, it will toggle between connect and disconnect status. Click button, Open the user manual document. - Page 27 CONTROL THE MATRIX BY IP LAN1 LAN2 Smartphone Cat 5e/6 Matrix CONFIG IRINPUT IROUTPUT Cat 5e/6 MadeInChina RS232 DC12V HDMIOUTD UTPOUTD UTPOUTC HDMIOUTC HDMIIN4 HDMIIN3 HDMIIN2 HDMIIN1 HDMIOUTB UTPOUTB UTPOUTA HDMIOUTA...
Need help?
Do you have a question about the JTECH-HD4X48 and is the answer not in the manual?
Questions and answers