Download Print this page
Hide thumbs Also See for P 650:

Advertisement

Classification:
BR12-003a
2011-2012 LEAF; BRAKE PEDAL SENSITIVE AT SPEEDS
This bulletin has been amended. The Title, Applied Vehicles, Applied VIN and Date, and If You
Confirm sections have been revised. Please discard all previous versions.
APPLIED VEHICLES:
APPLIED VIN AND DATE :
IF YOU CONFIRM
• Customer may experience some brake sensitivity at speeds below 15 mph. The
customer may experience this issue while in stop-and-go traffic conditions.
And
• No DTCs are present in the Electrically-driven Intelligent Brake Control Unit.
If DTCs are present, refer to the specific section of the applicable Electronic
Service Manual (ESM) and diagnose first.
ACTION
1. Refer to step 14 in the SERVICE PROCEDURE to confirm this bulletin applies to the
vehicle you are working on.
2. If this bulletin applies, reprogram the Electrically-driven Intelligent Brake Control Unit
with CONSULT III plus (CIII plus).
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
Reference:
NTB12-086a
BELOW 15 MPH
2011-2012 LEAF (ZE0)
Built before JN1AZ0CP(*)CT 023494 // June 6, 2012
1/20
Date:
October 25, 201 2

Advertisement

loading
Need help?

Need help?

Do you have a question about the P 650 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HURST P 650

  • Page 1 Classification: Reference: Date: BR12-003a NTB12-086a October 25, 201 2 2011-2012 LEAF; BRAKE PEDAL SENSITIVE AT SPEEDS BELOW 15 MPH This bulletin has been amended. The Title, Applied Vehicles, Applied VIN and Date, and If You Confirm sections have been revised. Please discard all previous versions. APPLIED VEHICLES: 2011-2012 LEAF (ZE0) Built before JN1AZ0CP(*)CT 023494 // June 6, 2012...
  • Page 2: Service Procedure

    CLAIMS INFORMATION Submit a Primary Part (PFP) line claim using the following claims coding: DESCRIPTION OP CODE Reprogram E-Act PX65AA (1) Refer to the electronic parts catalog (FAST) and use the appropriate ABS actuator assembly part number (46007-*****) as the Primary Part (PFP). SERVICE PROCEDURE Reprogram Electrically-driven Intelligent Brake Control Unit 1.
  • Page 3 3. Once all ASIST and CONSULT related updates have been verified/performed, attach the CONSULT PC to vehicle. • Connect the plus VI to the vehicle. • Connect the CONSULT PC to the plus VI with the USB cable. • Connect the AC adapter to the CONSULT PC. 4.
  • Page 4 7. Select Next. Step Figure 2 8. Select LEAF and 2011/ 2012 or Automatic Selection (VIN). • If Automatic Selection (VIN) is selected, wait for the Reading VIN screen to complete (picture not shown). 9. Select Select. This works, Step Step Figure 3 4/20...
  • Page 5 10. Verify the VIN in VIN or Chassis # matches that of the vehicle’s. • If the correct VIN exists, select Confirm. Verify here If OK, select Confirm Figure 4 11. On the next screen, select Confirm. Step Figure 5 5/20 NTB12-086a...
  • Page 6 12. Select BRAKE. • Wait for system call to complete. Step Figure 6 13. Select Reprogramming. Step Figure 7 6/20 NTB12-086a...
  • Page 7 14. Write down the Part Number on the vehicle’s repair order (see Figure 8). • If the BRAKE part number is 46007-3NA0A, continue with reprogramming. Select Save, and then go to Step 15. • If the BRAKE part number is not 46007-3NA0A, this bulletin does not apply or it has already been done.
  • Page 8 16. Read the precautions on page 1, and then select page 2 (page 2 not shown) with arrow. After reading page 2, select Confirmed instructions, and then select Next. Step Figure 10 NOTE: In some cases, more than one new P/N for reprogramming is available. In this case, the screen in Figure 11 will display.
  • Page 9 17. Verify “Current” and “After Reprogramming” part numbers are listed, then select Next. Verify P/Ns above, then select Next Figure 12 18. If this screen appears, select Other Operation. Step Figure 13 9/20 NTB12-086a...
  • Page 10 19. Open the hood, and then set up the GR8 Multitasking Battery Diagnostic Station (battery tester/charger) for the 12V battery. • For battery charger/tester setup, refer to Page 20, GR8 Multitasking Battery Diagnostic Station Setup. CAUTION: Battery voltage must stay between 12 volts and 15.5 volts. CAUTION: Do not charge the High Voltage (HV) Lithium Ion battery during reprogramming.
  • Page 11 21. On the next screen, select Start. • The reprogramming process begins when Start has been selected. NOTE: For reprogramming to continue, vehicle 12 V battery voltage must stay within 12 volts and 13.5 volts. Make sure the voltage level is sufficient. Monitor 12 V battery voltage here...
  • Page 12 23. When the screen in Figure 18 appears, reprogramming is complete. a. Select Next. b. Wait for System Call to complete. Step Figure 18 24. Erase all DTCs: a. Turn “ignition” off by depressing the power switch once. • The screen in Figure 19 will read OFF after pressing the power switch once. ON to Figure 19 12/20...
  • Page 13 b. Turn “ignition” on by depressing the power switch twice. • Do not step on the brake pedal when depressing the power switch. • The screen in Figure 20 will read ON after pressing the power switch twice. NOTE: Do not be confused by any screen messages. At this point, simply turn the “ignition”...
  • Page 14 25. Verify the part number has changed. a. Print a copy by selecting Print. NOTE: Before and after part numbers on your print-out may be switched compared to your CONSULT PC screen. This is ok. b. Attach the copy to the repair order. c.
  • Page 15 27. Close C-III plus (see previous page, Figure 23). • Do not turn off the CONSULT PC. 28. Place the vehicle in “READY to drive” mode: • Apply the parking brake. • Depress the brake pedal. • Depress the power switch once. •...
  • Page 16 31. Select LEAF and 2011/2012 or Automatic Selection (VIN). • If Automatic Selection (VIN) is selected, wait for the Reading VIN screen to complete. 32. Select Select or Detect Vehicle, whichever displays. This works, Step Step 32: May display Detect Vehicle Figure 25 33.
  • Page 17 34. Wait for system call to complete. Figure 27 35. To clear any remaining DTC’s (as sown in Figure 28): a. Turn “ignition” off (depress power switch once). b. Close CIII plus application. c. Wait for 5 minutes. Figure 28 17/20 NTB12-086a...
  • Page 18 36. After 5 minutes, check DTC status by again performing steps 28 through 34. Once done proceed to step 37. • Figure 29 should now be displayed with C1A60 as a PAST DTC. PAST Figure 29 37. Turn “ignition” OFF again (depress power switch once), and wait 15 seconds; then turn ignition to “READY to drive”...
  • Page 19 38 Select ERASE button. • All DTC’s should now be clear. Figure 31 39. Once all DTCs have been erased: a. Select Home, and then on the next screen, select Yes (picture not shown). b. Close C-III plus, turn off the CONSULT PC, and then disconnect the CONSULT PC and plus VI from the vehicle.
  • Page 20 GR8 Multitasking Battery Diagnostic Station Setup 1. Connect the battery tester/charger to the 12 V battery, positive cable first. 2. Plug in the battery tester/charger (AC voltage supply), and then turn on the battery tester/charger. 3. Select the preferred language, and then depress NEXT. 4.