LG 47LM6400 Service Manual page 42

4.5. ADC Calibration : Comp 480i/Comp 1080p/RGB
4.5.1. ADC Calibration : Internal Auto ADC
1) Press "ADJ" key on R/C for adjustment.
2) Enter Password number. Password is "0 0 0 0".
3) Move to the "8. ADC Calibration" by using ▲/▼(CH +/-) and
press ENTER(►).
4) Move to the "ADC Type" by using ▲/▼(CH +/-)
5) Press the right direction key(►) to ADC Type "OTP".
6) Press the right direction key(►) to Start.
7) After about a few seconds, appear "ADC Calibration
Completed", then complete
4.5.2. ADC Calibration - Manual
※ Required Equipments
▪ Remote controller for adjustment
▪ MSPG-925F/MSPG-1025/MSPG-3233 Pattern Generator
4.5.2.1. Process
1) Change the Input to Component1 or 2 mode..
2) Input the Component 480i@60Hz 100% Color Bar YPbPr
signal into Component1 or 2.
(MSPG-925F 480i Model: 209 / Pattern: 65 )
(MSPG-925F 1080p Model: 225 / Pattern: 65 )
3) Press "ADJ" key on R/C for adjustment.
4) Enter Password number. Password is "0 0 0 0".
5) Move to the "8. ADC Calibration" by using ▲/▼(CH +/-) and
press ENTER(►).
6) Move to the "ADC Type" by using ▲/▼(CH +/-)
7) Press the right direction key(►) to ADC Type "External".
8) Press the right direction key(►) to Start.
9) After about a few seconds, appear "ADC Calibration
Completed", then complete.
10) Change input source component 1080p, Do 3)~9) steps.
11) Change input source RGB 1080p and Do 3)~9) steps.
Copyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
[Fig. 2]
4.6. Check SW Version
4.6.1. Method
1) Push In-star key on Adjust remote-controller.
2) SW Version check(ex. 47LW9800-DA)
IN START
Model Name : 47LW9800-DA
Serial Number : 012PTED6N500
S/W Version : 3.02.06.01
MICOM Version : 3.05.3
BOOT Version : 1.02.22
FRC Version : 1.50
IR LED Version : c8
EDID(RGB/HDMI) : 0.03/0.02
Chip Type : BCM35230
Wireless Host Ver. : 0.00.0
Wireless B/B Ver. : 0.00.0
Wi-Fi Version :1.0
Wi-Fi Channel :0
Wi-Fi MAC :00:00:00:00:00:00
MAC Address :FF:FF:FF:FF:FF:FF
Widevine :LGTV10L000011618
Local Dimming Ver. :0x0707
Formatter Version : 0.6c
RF Receiver Version :
Debug Status : Release
UTT : 40
APP History Ver. : 35190
PQL DB : LGD_AF_LGT10_xxxxxx
5. SET assembly adjustment method
5.1. Input Area-Option
(1) Profile : Must be changed the Area option value because
being different of each Country's Language and
signal Condition.
(2) Equipment : adjustment remote control.
(3) Adjustment method
- The input methods are same as other chassis.(Use IN-START
Key on the Adjust Remocon.)
Refer to Job Expression of each main chassis ass'y
(EBTxxxxxxxx) for Option value
5.2. Adjustment of White Balance
● In case of keeping module is in the circumstance of 0°C, it
should be placed in the circumstance of above 15°C for 2
hours
● In case of keeping module is in the circumstance of below
-20°C, it should be placed in the circumstance of above 15°C
for 3 hours.
- 16 -
Adjust Check
1.Adjust Check
▶
2.ADC Date 1. Country Group(Press OK to Save)
3.Power Off Status Country Group Code
4.System1 Country Group
5.System2 Country
6.Model Number D/L 2. Tool Option
7.Test Option Tool Option1
8.External ADC Tool Option2
9.Spread Spectrum Tool Option3
10.Sync Level Tool Option4
11.Wireless Ready Tool Option5
12.Stable Count Tool Option6
13.ODC Test 3. Adjust White Balance :
14.Local Dimming 4. Adjust ADC :
15.SDP Server Selection 480i Component
16. Network Error History 1080p Component
RGB
5.EDID :
RGB
HDMI1
HDMI2
HDMI3
HDMI4
LGE Internal Use Only
10
TW
TW/CB/PA
33112
5461
3327
17593
47695
697
OK
OTP
OK
OK
OK
OK
OK(0x98)
OK(0x7F,0xCB)
OK(0x7F,0xBB)
OK(0x7F,0xAB)
OK(0x7F,0x9B)