Input Tool Option; Edid D/L Method - LG 47LM6400 Service Manual

4.4. Input tool option.

Adjust tool option refer to the BOM.
▪ Tool Option Input : PCBA Check Process
▪ Area Option Input : Set Assembly Process
*** Tool Option table
MODEL 32LS5700 32LS5700 42LS5700
(AUO)
Tool Option1 4452 356
Tool Option2 9557 9557
Tool Option3 845 845
Tool Option4 12910 12910
Tool Option5 4765 21021
Tool Option6 1321 1321
Tool Option7 4651 555
MODEL 32LM6200 37LM6200 42LM6200
(AUO)
Tool Option1 116 117
Tool Option2 9557 9557
Tool Option3 17229 17229
Tool Option4 12910 12910
Tool Option5 23069 23069
Tool Option6 1321 1321
Tool Option7 555 555
MODEL 32LM6400 42LM6400 47LM6400
Tool Option1 33156 33158
Tool Option2 42325 42325
Tool Option3 17229 17229
Tool Option4 12911 12909
Tool Option5 23191 23191
Tool Option6 1321 1321
Tool Option7 1963 6059
MODEL 42LM6700 47LM6700 55LM6700
Tool Option1 32950 32951
Tool Option2 42325 42325
Tool Option3 17229 17229
Tool Option4 12909 12909
Tool Option5 23191 23191
Tool Option6 1321 1321
Tool Option7 6059 6059
After Input Tool Option and AC off
Before PCBA check, you have to change the Tool option and
have to AC off/on (Plug out and in)
(If missing this process, set can operate abnormally)
Copyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
47LS5700 55LS5700
358 359 361
9557 9557 9557
845 845 845
12908 12908 12908
21021 21021 21021
1321 1321 1321
4907 4395 4395
47LM6200 55LM6200 65LM6200
118 119 121 36987
9557 9557 9557 9557
17229 17229 17229 17229
12908 12908 12908 12910
23069 23069 23069 6685
1321 1321 1321 1321
4907 4395 4395 12311
55LM6400 42LM6600 42LM6690
33159 33161 32934 32934
42325 42325 42325 42325
17229 17229 17229 17229
12909 12909 12909 12909
23191 23191 23191 23191
1321 1321 1321 1321
6059 6059 6059 6059
42LM7600 47LM7600 55LM7600
32953 32966 32967 32969
42325 42325 42325 42325
17229 17229 17229 17229
12909 12909 12909 12909
23191 23191 23191 23191
1321 1321 1321 1321
6059 13355 13611 13611
4.4.1. Profile
Must be changed the option value because being different with
some setting value depend on module maker, inch and market
4.4.2. Equipment
Adjustment remote control
4.4.3. Adjustment method
The input methods are same as other chassis.(Use ADJ Key
on the Adjust Remocon.)
(If not changed the option, the input menu can differ the model
spec.)
Refer to Job Expression of each main chassis ass'y
(EBTxxxxxxxx) for Option value
Caution : Don't Press "IN-STOP" key after completing the
function inspection.

4.5. EDID D/L method

Recommend that don't connect HDMI and RGB(D-SUB) cable
when downloading the EDID.
If not possible, recommend that connect the MSPG equipment.
There are two methods of downloading the edid data
4.5.1. 1st Method
EDID datas are automatically downloaded when adjusting the
Tool Options.
Automatically downloaded when pushing the enter key after
adjusting the tool option5.
It takes about 2seconds
47LM6690
32935
4.5.2. 2nd Method
42325
● Caution : Must be checked that the tool option is right or not.
17229
If tool option is wrong, hdmi edid data could not be
downloaded well.
12909
1) Press the ADJ key
23191
2) Move to the 10. EDID D/L and Press the right direction
1321
key(►)
6059
3) Press the right direction key(►) at Start.
4) After about a few seconds, appear "Waiting.." => "OK", then
42LM7600
compele.
32966
42325
4.5.3. RS-232C command Method
17229
1) Command : AE 00 10
● Caution : Don't connect HDMI and RGB(D-SUB) cable when
12909
downloading the EDID.
23191
If the cables are connected, Downloading of edid
1321
could be failed
13355
- 12 -
LGE Internal Use Only