HP Compaq 6530s Replacement Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. Compaq 6530s
  6. Replacement manual
HP Compaq 6530s Replacement Manual

HP Compaq 6530s Replacement Manual

Display replacement guide
Hide thumbs Also See for Compaq 6530s:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Maintenance and Service Manual
HP Compaq 6530s Notebook PC
HP Compaq 6531s Notebook PC
HP Compaq 6535s Notebook PC
Display Replacement Guide

Advertisement

Table of Contents
loading

Related Manuals for HP Compaq 6530s

Summary of Contents for HP Compaq 6530s

  • Page 1 HP Compaq 6530s Notebook PC HP Compaq 6531s Notebook PC HP Compaq 6535s Notebook PC Display Replacement Guide...
  • Page 2 Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
  • Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
  • Page 4 Safety warning notice ENWW...

  • Page 5: Table Of Contents

    Table of contents 1 Removal and replacement procedures Preliminary replacement requirements ....................2 Tools required ........................2 Service considerations ......................2 Plastic parts ......................2 Cables and connectors ..................3 Drive handling ..................... 3 Grounding guidelines ......................4 Equipment guidelines ..................4 Component replacement procedures ....................
  • Page 6 ENWW...

  • Page 7: Removal And Replacement Procedures

    Removal and replacement procedures ENWW...

  • Page 8: Preliminary Replacement Requirements

    Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 9: Cables And Connectors

    Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.

  • Page 10: Grounding Guidelines

    Grounding guidelines Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 11: Component Replacement Procedures

    493154-001 14.1-inch, WXGA display assembly with camera 493152-001 14.1-inch, WXGA display assembly 493151-001 For use only with HP Compaq 6530s and 6531s Notebook PC models 14.1-inch, WXGA BrightView display assembly with camera 491643-001 14.1-inch, WXGA display assembly with camera 491642-001 14.1-inch, WXGA BrightView display assembly...
  • Page 12 Remove the battery (2) from the computer. Remove the following screws: (1) Two slotted Torx ST8M2.5×7.0 screws (2) Two Torx T8M2.0×2.0 broadhead (9-mm) screws Chapter 1 Removal and replacement procedures ENWW...
  • Page 13 Remove the two slotted Torx ST8M2.5×7.0 screws that secure the keyboard to the computer. Turn the computer display-side up, with the front toward you. Open the computer as far as possible. Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2) until it rests on the display assembly.
  • Page 14 Release the zero insertion force (ZIF) connector to which the LED board cable is attached, disconnect the LED board cable from the system board (1), and lift the switch cover up to remove it (2) from the system board. To disengage the four tabs (1) on the back of the keyboard from the switch cover, lift up the rear edge of the keyboard (2), and slide it back (3).
  • Page 15 Release the swinging ZIF connector (1) to which the keyboard cable is attached, and disconnect the keyboard cable (2) from the system board. Remove the keyboard. Turn the switch cover over. Remove the two Phillips PM2.0×2.0 broadhead screws (1) from the switch cover. Remove the LED power button board (2) from the switch cover.
  • Page 16 Remove the speakers (3) from the top cover. Turn the computer right-side up, with the front toward you. Open the computer as far as possible. Disconnect the display panel cable (1) from the system board. CAUTION: There is a ground loop off the display panel cable that is secured to the left hinge. Be sure you do not pull or damage the cable.
  • Page 17 The rubber screw covers are available in the Rubber Kit, spare part numbers 497622-001 (for use only with HP Compaq 6535s Notebook PC models) and 491654-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models).
  • Page 18 (2). The webcam module can be ordered by using spare part numbers 491630-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models) and 493171-001 (for use only with HP Compaq 6535s Notebook PC models).
  • Page 19 Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter. Remove the display inverter. The display inverter is available using spare part numbers 497615-001 (for use only with HP Compaq 6535s Notebook PC models) and 491634-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models).
  • Page 20 (1) that secure the wireless antenna transceiver to the top cover. The wireless antenna cables are included in the Display Cable Kit, spare part numbers 497620-001 (for use only with HP Compaq 6535s Notebook PC models) and 491637-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models).
  • Page 21 (1) from the clips and routing channels (2) built into the top cover. The webcam cable is included in the Display Cable Kit, spare part numbers 497620-001 (for use only with HP Compaq 6535s Notebook PC models) and 491637-001 (for use only with HP Compaq 6530s and 6531s Notebook PC models).
  • Page 22 Chapter 1 Removal and replacement procedures ENWW...

  • Page 23: Recycling

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
  • Page 24 Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.
  • Page 25 Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.
  • Page 26 Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.
  • Page 27 Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight frame from the display panel.
  • Page 28 Remove the backlight from the backlight frame. Disconnect the display panel cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.

  • Page 29: Index

    Index cables, service considerations 3 optical drive connectors precautions 3 service considerations 3 plastic parts 2 diskette drive precautions 3 removal/replacement display assembly preliminaries 2 removal 5 procedures 5 spare part numbers 5 display bezel removal 11 service considerations 2 spare part number 12 static-shielding materials 4 display component recycling 17...
  • Page 30 Index ENWW...

This manual is also suitable for:

Compaq 6535sCompaq 6531s

Table of Contents