Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Triton Blue MF-7
Summary of Contents for Triton Blue MF-7
- Page 1 PROFESSIONAL LIGHT USER’S MANUAL MF-7 KEEP THIS MANUAL FOR FUTURE NEEDS...
- Page 2 For your own safety, please read this user manual carefully before installing the device. Every person involved with the installation, operation and maintenance of this device has -be qualified -follow carefully the instructions of this manual INTRODUCTION: Thank you for having chosen this professional moving head. You will see you have acquired a powerful and versatile device.
- Page 3 Overview: (1) Fixation screw (2) DMX-In socket (3) DMX-Out socket (4) Power supply/Fuse holder (5) Mounting bracket (6) Ventilator (7) DIP-switches (8) Blackout controller jack (9) MIC Sensitivity-button (10) Lamp system Features ·Lamp: Philips MSD 250/2 8500K, base : GY 9.5 ·Control signal: standard DMX-512, 4 channels ·Stand alone operation with master/slave function, can be sound activated ·One special designed color and gobo wheel...
-
Page 4: Safety Instructions
·Preset program: 8 built in programs can be called up via DMX controller SAFETY INSTRUCTIONS This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. -
Page 5: General Guidelines
Please be aware that damages caused by manual modifications to the device are not subject to warranty. Keep away from children and non-professionals. GENERAL GUIDELINES This device is a lighting effect for professional use on stages, in discotheques, theatres, etc. This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual, the device was designed for indoor use only. -
Page 6: Installation Instructions
operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc. INSTALLATION INSTRUCTIONS a) Installing or replacing the lamp Before replacing the lamp let the lamp cool down, because during operation, the lamp can reach very high temperature. During the installation of halogen lamps do not touch the glass bulbs bare handed. Always use a cloth to handle the lamps during insertion and removal. - Page 7 Please remember the lamp is not a hot-restrike type, you must wait for approximately 10 minutes after having turned off the lamp before you can turn it back on again. b) Mounting the device The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.
- Page 8 Cautions: The effect should be installed outside areas where persons may reach it, walk by or be seated. Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device.
- Page 9 installation via the Clamp Screw one clamp each via a M10 screw and nut directly into the bracket of the unit. Pull the safety-chain through the eyelet on the rear of the unit and over the trussing system or a safe fixation spot.
- Page 10 Occupation of the DIP-switches: Blackout-socket If you wish to lock the light output - e.g. via an optional footswitch (Blackout-mode), connect your footswitch via a mono-jack plug to the Blackout-socket. Occupation mono 1/4“ jack-plug: DMX-512 connection / connection between fixtures Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
- Page 11 XLR socket of the last fixture in the chain. While on the MF-7 which with the dip Switches setting, if the DP12 is put to ON position ( downwards) the fixture gains the function of connecting with a 120 Ω resistor, then this unit functions as the terminator of the DMX link.
-
Page 12: Operation
Occupation of the DIP-switches: Connection with the mains Connect the device to the mains with the enclosed power supply cable. The occupation of the connection-cables is as follows: The earth has to be connected! If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation. - Page 13 Stand Alone operation In the Stand Alone mode, the LIGHTING EFFECT can be used without controller. You can do without a controller as the LIGHTING EFFECT features a built-in microphone, which provides automatic sound control. Disconnect the LIGHTING EFFECT from the controller and set the DIP-switch 10 to On.
-
Page 14: Cleaning And Maintenance
Channel 3 - Shutter, strobe Shutter closed Shutter closed & Motor Reset 8-31 Shutter closed 32-63 Dimmer (close to open) 64-95 Strobe effect slow to fast 96-127 No function (shutter open) 128-159 Pulse-effect in sequences 160-191 No function (shutter open) 192-223 Random strobe effect slow to fast 224-255... - Page 15 We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents! The objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing the light-output very quickly. The cooling-fans should be cleaned monthly. The gobos may be cleaned with a soft brush.
-
Page 16: Technical Specifications
TECHNICAL SPECIFICATIONS Power supply : □100VAC,50Hz;□110VAC,50Hz;□120VAC, 50Hz;□220VAC,50Hz;□230VAC,50Hz;□240VAC, 50Hz; □98VAC,50Hz;□110VAC,60Hz;□120VAC,60Hz; □220VAC,60Hz;□230VAC,60Hz;□240VAC,60Hz; Power consumption : max. 400W Lamp : MSD250 /2 Motors : 3 micro motors Packing dimensions : 51 x 37 x 34 cm Sound-control: via built-in microphone Net weight : 10KGS; Gross weight: 12KGS;... - Page 17 PCB wiring circuit diagram WIT042 V1.1-01NR...
Need help?
Do you have a question about the MF-7 and is the answer not in the manual?
Questions and answers