Page 1
RX-7001PGD SERVICE MANUAL AUDIO/VIDEO CONTROL RECEIVER RX-7001PGD Area Suffix Australia China Singapore TV/CATV/DBS DVD MUILTI TAPE/MD TV/DBS PHONO FM/AM ANALOG/DIGITAL SLEEP SURROUND CENTER ON/OFF MENU MENU TEST REAR-L SURROUND MODE ENTER ENTER CD-DISC EFFECT REAR-R SOUND SEA MODE SUBWOOFER RETURN...
RX-7001PGD Safety Precautions 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer.
Page 3
RX-7001PGD Disassembly method Top cover Removing the top cover (See Fig.1) Remove the four screws A attaching the top cover on both sides of the body. Remove the three screws B on the back of the body. Remove the top cover from behind in the direction of Fig.1...
Page 4
RX-7001PGD Removing each board connected to the rear side of the main board CN202 (See Fig.5 to 9) Prior to performing the following procedure, remove the top cover and the rear panel. Cut off the tie band fixing the harness.
Page 5
RX-7001PGD Removing the main board / regulator Relay board 1 CN821 CN704 CN901 board (See Fig.10 to 12) Relay board 2 Prior to performing the following procedure, remove the top cover and the rear panel. Power supply Main board board...
Page 6
RX-7001PGD Removing the amplifier board CN821 CN704 Relay board 1 CN901 (See Fig.10 and 14) Relay board 2 Prior to performing the following procedure, remove the top cover. Power supply Main board board CN400 Cut off the four tie bands fixing the harnesses.
Page 7
RX-7001PGD Removing the power supply board (See Fig.18 and 19) Prior to performing the following procedure, remove the top cover and the front panel. Remove the one nut attaching the headphone jack of the power supply board on the front side of the body.
Page 8
RX-7001PGD Removing the operation switch board (See Fig.22 to 24) Front panel Prior to performing the following procedure, remove the top cover, the front panel assembly and the system control board. Remove the six screws R attaching the operation switch board on the back of the front panel.
Page 9
RX-7001PGD Adjustment method Tuner section 1.Tuner range 87.5MHz~108.0MHz AM(MW) 530kHz~1710kHz Power amplifier section Adjustment of idling current Measurement location TP781 Adjustment part VR787(Lch) , VR788(Rch) Attention This adjustment does not obtain a correct adjustment value immediately after the amplifier is used (state that an internal temperature has risen).
Page 11
RX-7001PGD 3. Pin function (1/2) AK4527(1/2) Pin name Function SDTO Source select pin SDOS "L" : Internal ADC output, "H" : DAUX input ORed with serial control register if P/S="L". MCKO Clock frequency select pin OCKS "L" : MCLK, "H" : MCLK/2.
Page 12
RX-7001PGD 3.Pin function (2/2) AK4527(2/2) Pin Name Function VREFL Negative voltage reference Input pin, AVSS VCOM Common voltage output pin,AVDD/2 Large external capacitor around 2.2uF is used to reduce power-supply noise VREFH Positive voltage reference input pin,AVDD AVDD Analog power supply pin...
Page 14
RX-7001PGD BU2092(IC402,IC405):LED Controller 1.Terminal Layout DATA CLOCK CONTROL CIRCUIT 2.Pin Function Symbol Function Pin No. Connect to GND DATA Serial Data input CLOCK Shift Clock of Data Latch Clock of Data 5~16 Q0~Q11 Parallel Data Output Latch Data OUTPUT ON OFF...
Page 16
RX-7001PGD LA1838(IC102): FM AM IF AMP&detector, FM MPX Decoder 1. Block Diagram DECODER RF.AMP ANIT-BIRDIE MUTE BUFF STEREO P-DET AM IF PILOT 384KHz COMP S-METER AM/FM S-CLRVE S-METER IF-BUFF TUNING STEREO DRIVE DRIVE FM IF 2. Pin Function Symbol Function...
Page 18
RX-7001PGD LC7522 (IC451) : SEA Control 1.Pin layout 2.Block diagram – – 26 IN2 27 IN1 Network Network Resistor Resistor Latch Circuit Control Shift Resistor 12 TEST2 TEST1 3.Pin function Pin No. Symbol Function Power Supply terminal for Audio signal +7V(typ) Power Supply terminal 0V Power Supply terminal for Audio signal.
Page 19
RX-7001PGD M5243AP12(IC452):S.E.A.Graphic equalizer IN1-2 NF1-2 IN2-2 NF2-2 IN3-2 NF3-2 IN-2 IN-2 OUT-2 VDD Vref. Vref. IN1-1 NF1-1 IN2-1 NF2-1 IN3-1 NF3-1 IN-1 IN-1 OUT-1 GND NJM4580D (IC301, IC302, IC306) : LPF, Mic and H.phone Amp. 1.Terminal layout A OUT A -IN...
Page 20
RX-7001PGD MN101C15FDE (IC401) : System control micon 1. Pin layout 2. Pin function Functions Functions Symbol Symbol VIDEO3 Ground VIDEO 3 signal terminal VIDEO4 DVD S/C signal select terminal VIDEO 4 signal terminal DVD-S/C VCR1 S/C signal select terminal S.MUTE...
Page 21
RX-7001PGD MN173222DG(IC400):FL Display & Operation switch control 1.Pin layout 2.Key matrix KEY OUT 2 KEY OUT 0 KEY OUT1 KEY OUT 3 KEY OUT 5 KEY IN 0 SEA ADJUST POWER ANALOG/ FM/AM TUNING ONE TOUCH DIGITAL OPERATION KEY IN 1...
Page 22
RX-7001PGD MB90088 (IC203) : On screen display controller 1.Terminal layout AVss YOUT VOUT AVcc COUT FSCO VBLK SCLK TEST VOC0 HSYNC VOC1 VSYNC VOC2 EXHSYN EXVSYN 2.Block diagram Serial Input Each Control, Data SCLK Control EXHSYN H/V Separate EXVSYN VOUT...
Page 23
RX-7001PGD 3.Pin functions (MB90088) Symbol I/O Function Brightness signal Input terminal for Superinpause indication Composite video signal input terminal for Superinpause indication Contrast signal input terminal for Superinpause indication Analog power supply terminal AVcc Color (Brightness) signal output terminal IOUT...
Page 24
RX-7001PGD NJM2285D (IC202) : Video switch 1.Terminal layout & Block diagram GND 1 IN 2B CTL 2 IN 2A GND 3 IN 3B IN 1A Clamp Type Bias Type Clamp Type IN 1B CTL 1 OUT 1 GND 2 OUT 2...
Page 27
RX-7001PGD UPD78F4216AGC(IC671):UNIT CPU 1.Pin layout 2.Pin function Pin No. Symbol Function Non connect Power supply terminal Connecting the crystal oscillator for system main clock Connecting the crystal oscillator for system main clock Connect to GND Connecting the crystal oscillator for system sub clock...
RX-7001PGD Block diagrams System control & Video I/O section DVD IN TV/BS J241 VCR1 OUT J201 TV/BS IN VCR1 IN J202 VCR1 J242 VCR1 IN MONITOR J203 MONITOR J243 CN202 CN450 CN410...
Page 40
RX-7001PGD Tuner section FM/TUNER Signal SHEET END Parts are safety assurance parts. When replacing those parts make sure to use the specified one. CN101 2-13...
RX-7001PGD PARTS LIST [ RX-7001PGD ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix A ------------------------- Australia UF --------------------------- China US --------------------- Singapore - Contents - Exploded view of general assembly and parts list...
Page 48
RX-7001PGD Exploded view of general assembly and parts list Block No. SEA board SEA board Tuner Tuner Audio Audio board board Vol.selector V-Audio V-Audio board board SP.terminal Video Ver.UF only board DSP board DSP board board Center tone board S-Video S-Video Ver.US only...
Page 49
RX-7001PGD Parts list ( General assembly ) Parts list ( General assembly ) Block No. M1MM Block No. M1MM Item Parts number Parts name Q'ty Description Area Item Parts number Parts name Q'ty Description Area LV10018-037A FRONT PANEL E409257-001 GND TERMINAL...
RX-7001PGD Electrical parts list Block No. 01 Electrical parts list ( Main board ) Ver.A/US Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 701 QETN1HM-106Z E CAPACITOR 10MF 20% 50V CN241 QGB2510J1-04 CONNECTOR...
Page 51
RX-7001PGD Block No. 01 Electrical parts list ( Main board ) Ver.A/US Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area C1390 QETN1EM-476Z E CAPACITOR 47MF 20% 25V IC362 BA15218N C1391 QFLC1HJ-562Z M CAPACITOR 5600PF 5% 50V...
Page 52
RX-7001PGD Block No. 01 Electrical parts list ( Main board ) Ver.A/US Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area R 753 QRJ146J-100X UNF C RESISTOR 10 5% 1/4W R 915 QRE141J-823Y C RESISTOR...
Page 53
RX-7001PGD Block No. 01 Electrical parts list ( Main board ) Ver.A/US Item Remarks Parts number Parts name Area R1389 QRZ9005-680X F RESISTOR 68 1/0W R1390 QRZ9005-680X F RESISTOR 68 1/0W R1391 QRE141J-472Y C RESISTOR 4.7K 5% 1/4W R1392 QRE141J-472Y C RESISTOR 4.7K 5% 1/4W...
Page 54
RX-7001PGD Block No. 02 Electrical parts list ( Main board ) Ver.UF Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area C 701 QETC1HM-106Z E CAPACITOR 10MF 20% 50V CN241 QGB2510J1-04 CONNECTOR C 702 QETC1HM-106Z...
Page 55
RX-7001PGD Block No. 02 Electrical parts list ( Main board ) Ver.UF Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area C1390 QETC1EM-476Z E CAPACITOR 47MF 20% 25V IC362 BA15218N C1391 QFLC1HJ-562Z M CAPACITOR 5600PF 5% 50V...
Page 56
RX-7001PGD Block No. 02 Electrical parts list ( Main board ) Ver.UF Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area R 753 QRJ146J-100X UNF C RESISTOR 10 5% 1/4W R 915 QRE141J-823Y C RESISTOR...
Page 57
RX-7001PGD Block No. 02 Electrical parts list ( Main board ) Ver.UF Item Remarks Parts number Parts name Area R1389 QRZ9005-680X F RESISTOR 68 1/0W R1390 QRZ9005-680X F RESISTOR 68 1/0W R1391 QRE141J-472Y C RESISTOR 4.7K 5% 1/4W R1392 QRE141J-472Y C RESISTOR 4.7K 5% 1/4W...
Page 58
RX-7001PGD Electrical parts list ( FL display & System control board) Block No. 03 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 400 QEKC1HM-475Z E CAPACITOR 4.7MF 20% 50V C1472 QFVJ1HJ-333Z MF CAPACITOR .033MF 5% 50V...
Page 59
RX-7001PGD Electrical parts list ( FL display & System control board) Block No. 03 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area IC451 LC7522 R 457 QRE141J-102Y C RESISTOR 1.0K 5% 1/4W IC452 M5243AP12...
Page 60
RX-7001PGD Electrical parts list ( FL display & System control board) Block No. 03 Item Parts number Parts name Remarks Area S 401 QSW0683-001Z PUSH SWITCH (SPK1) S 402 QSW0683-001Z PUSH SWITCH (SPK2) S 407 QSW0683-001Z PUSH SWITCH (SURROUND) S 408...
Page 61
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.A/US Block No. 04 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area QCZ9019-472 C CAPACITOR 4700PF C1803 QCS11HJ-101 C CAPACITOR 100PF 5% 50V...
Page 62
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.A/US Block No. 04 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area D1892 1SS133-T2 SI DIODE R 51 QRJ146J-153X UNF C RESISTOR 15K 5% 1/4W...
Page 63
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.A/US Block No. 04 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R1772 QRE141J-391Y C RESISTOR 390 5% 1/4W TA 2 QNZ0079-001Z R1773...
Page 64
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.UF Block No. 05 Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area QCZ9019-472 C CAPACITOR 4700PF C1803 QCS11HJ-101 C CAPACITOR 100PF 5% 50V...
Page 65
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.UF Block No. 05 Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area D1892 1SS133-T2 SI DIODE R 53 QRZ9015-3R3 FUSI RESISTOR 3.3 1/0W...
Page 66
RX-7001PGD Electrical parts list ( Power AMP & Power supply board) Ver.UF Block No. 05 Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area R1774 QRE141J-201Y C RESISTOR 200 5% 1/4W TH731 QAD0012-202 THERMISTOR R1791...
Page 67
RX-7001PGD Block No. 06 Electrical parts list ( SP terminal board ) Item Remarks Parts number Parts name Area C 813 QETN1HM-475Z E CAPACITOR 4.7MF 20% 50V C 814 QETN1HM-475Z E CAPACITOR 4.7MF 20% 50V C 815 QETN1HM-475Z E CAPACITOR 4.7MF 20% 50V...
Page 68
RX-7001PGD Electrical parts list ( Input / output board) Ver.A/US Block No. 07 Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area C 201 QETN1HM-475Z E CAPACITOR 4.7MF 20% 50V C 319 QCF31HZ-223Z C CAPACITOR .022MF +80:-20%...
Page 69
RX-7001PGD Electrical parts list ( Input / output board) Ver.A/US Block No. 07 Item Parts number Parts name Remarks Area R 349 QRE141J-104Y C RESISTOR 100K 5% 1/4W R 350 QRE141J-104Y C RESISTOR 100K 5% 1/4W R 351 QRE141J-104Y C RESISTOR...
Page 70
RX-7001PGD Electrical parts list ( Input / output board) Ver.UF Block No. 08 Item Remarks Parts number Parts name Area Item Parts number Parts name Remarks Area C 201 QETC1HM-475Z E CAPACITOR 4.7MF 20% 50V C 319 QCF31HZ-223Z C CAPACITOR .022MF +80:-20%...
Page 71
RX-7001PGD Electrical parts list ( Input / output board) Ver.UF Block No. 08 Item Remarks Parts number Parts name Area Item Parts number Parts name Remarks Area C1251 QCBB1HK-221Y C CAPACITOR 220PF 10% 50V R 240 QRE141J-750Y C RESISTOR 75 5% 1/4W...
Page 72
RX-7001PGD Electrical parts list ( Input / output board) Ver.UF Block No. 08 Item Remarks Parts number Parts name Area R 351 QRE141J-104Y C RESISTOR 100K 5% 1/4W R 352 QRE141J-104Y C RESISTOR 100K 5% 1/4W R 353 QRZ9005-680X F RESISTOR...
Page 73
RX-7001PGD Block No. 09 Electrical parts list ( DSP board ) Item Remarks Item Parts number Parts name Remarks Area Parts number Parts name Area C 601 NCB31HK-102X C CAPACITOR C 697 NEA71HM-105X E CAPACITOR C 602 NCB31HK-102X C CAPACITOR...
Page 74
RX-7001PGD Electrical parts list ( DSP board ) Block No. 09 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C2574 NCB31HK-272X C CAPACITOR Q 675 DTC114YE-X TRANSISTOR C2575 NCB31HK-392X C CAPACITOR Q2501 DTA144EKA-X TRANSISTOR...
Page 75
RX-7001PGD Electrical parts list ( DSP board ) Block No. 09 Item Remarks Parts number Parts name Area Item Parts number Parts name Remarks Area R 673 NRSA63J-432X MG RESISTOR R2544 NRSA63J-103X MG RESISTOR R 674 NRSA63J-432X MG RESISTOR R2545...
Page 76
RX-7001PGD Block No. 10 Electrical parts list ( Tuner board ) Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area AT101 QNB0014-001 ANT TERMINAL R 124 NRSA02J-222X MG RESISTOR C 101 NCB21HK-103X C CAPACITOR R 126...
Page 77
RX-7001PGD Packing materials and accessories parts list Block No. Block No. Ver.US/UF A1~A5 A7,A10,A11 Ver.A A1,A3,A4 A7~A9 3-32...
Page 78
RX-7001PGD Parts list ( Packing ) Block No. M2MM Item Parts number Parts name Q'ty Description Area LV20806-006A CARTON BOX LV30044-0D7A CARTON BOX LV30044-0D4A CARTON BOX LV20809-001A PACKING PAD A,US LV20039-002A PACKING PAD LV20810-001A PACKING PAD A,US LV20040-001A PACKING PAD...
Page 79
RX-7001PGD VICTOR COMPANY OF JAPAN, LIMITED AUDIO & COMMUNICATION BUSINESS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan No.20881 200010(V)
Page 80
AUDIO/VIDEO CONTROL RECEIVER RECEPTOR DE CONTROL DE AUDIO/VÍDEO RECEPTOR DE COMANDO AUDIO/VÍDEO RX-7001PGD TV/CATV/DBS DVD MUILTI TAPE/MD TV/DBS PHONO FM/AM ANALOG/DIGITAL SLEEP SURROUND CENTER ON/OFF MENU MENU TEST REAR-L SURROUND MODE ENTER ENTER CD-DISC EFFECT REAR-R SOUND SEA MODE SUBWOOFER...
Page 81
Warnings, Cautions and Others / Avisos, precauciones y otras notas / Advertêcias, precauções e outras notas / CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. PRECAUCIÓN Para reducir riesgos de choques eléctricos, incendio, etc.: 1.
Page 82
Spacing 15 cm or more Espacio de 15 cm o más Espaço de 15 cm ou mais Front Frente Frente RX-7001PGD Wall or obstructions Pared u obstrucciones Parede ou obstáculo Stand height 15 cm or more Allura del soporte 15 cm o más...
Using the Sleep Timer .............. 17 AV COMPU LINK Remote Control System ..41 Receiving Radio Broadcasts ......18 Operating JVC’s Audio/Video Components ... 43 Tuning in Stations Manually ............ 18 Operating Audio Components ..........43 Using Preset Tuning ..............18 Operating Video Components ..........
Parts Identification Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details. MASTER VOLUME RX-7001P AUDIO/VIDEO CONTROL RECEIVER D I G I T A L – STANDBY SURROUND ON/OFF TV SOUND/DBS PHONO TAPE/MD STANDBY/ON...
Getting Started This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply. Before Installation Connecting the FM and AM Antennas General FM Antenna Connections • Be sure your hands are dry. •...
Basic connecting procedure AM Antenna Connections Snap the tabs on the loop into the ANTENNA slots of the base to assemble the FM 75 AM loop. COAXIAL R IG R IG R IG 1 Cut, twist and remove the insulation at the end of AM Loop Antenna LOOP each speaker signal cable (not supplied).
About the speaker impedance Connecting the subwoofer speaker The required speaker impedance of the front speakers does differ You can enhance the bass by connecting a subwoofer. depending on whether both the FRONT SPEAKERS 1 and FRONT Connect the input jack of a powered subwoofer to the SPEAKERS 2 terminals are used or only one of them is used.
Page 88
Video component connections CD player AUDIO RIGHT LEFT PHONO Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the CD player audio right jack, and the yellow plug to the video jack. If your video components have S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied).
Page 89
DVD player TV and/or DBS tuner • When you connect the DVD player with stereo output jacks: When connecting the TV, DO NOT connect the TV’s video output to these video input terminals. DVD player VIDEO RIGHT AUDIO RIGHT LEFT VIDEO S-VIDEO To audio...
Page 90
Digital connections Notes: • When shipped from the factory, the DIGITAL IN terminals have This receiver is equipped with three DIGITAL IN terminals — one been set for use with the following components. digital coaxial terminal and two digital optical terminals, and one –...
Connecting the Power Cord Putting Batteries in the Remote Control Before plugging the receiver into an AC outlet, make sure that all Before using the remote control, put two supplied batteries first. connections have been made. When using the remote control, aim the remote control directly at the remote sensor on the receiver.
Basic Operations The following operations are commonly used when you play any sound source. IMPORTANT: From the remote control: Press one of the source selecting buttons. When using the remote control, check to see if its AUDIO/ remote control mode selector is set to the correct TV/VCR DVD MUILTI TAPE/MD...
Signal and speaker indicators on the display Adjusting the Volume • The signal indicators light up to indicate the incoming channel signals. On the front panel: – Only the indicators for the incoming signals light up. MASTER VOLUME To increase the volume, turn MASTER •...
Listening only with headphones Attenuating the Input Signal You can listen with the headphones without deactivating both pairs of speakers; however, if you want to use the HEADPHONE mode When the input level of the playing source is too high, the sounds (see below), you must turn off both pairs of speakers.
Basic Settings Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier. IMPORTANT: 2. Turn MULTI JOG to adjust the MULTI JOG balance. When using the remote control, check to see if its AUDIO/ remote control mode selector is set to the correct •...
3. Repeat steps 1 and 2 to select the appropriate Setting the Subwoofer Information items for the other speakers. Register whether or not you have connected a subwoofer. Notes: Before you start, remember... • Keep the following comment in mind as reference when adjusting. •...
Page 97
Low Frequency Effect Attenuator Setting 2. Turn MULTI JOG to select the MULTI JOG delay time of the rear speaker If the bass sound is distorted while playing back a source using Dolby Digital, DTS Digital Surround or MPEG Multichannel follow output.
On the front panel: Digital Input (DIGITAL IN) Terminal 1. Turn SOURCE SELECTOR until Setting SOURCE SELECTOR the source (CD, MD, TV SOUND, DBS, or DVD)* for which you When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3).
Storing the Basic Settings and Adjustments — One Touch Operation Display JVC’s One Touch Operation function is used to assign and store When you have connected an MD recorder or CD player equipped different sound settings for each different playing source. By using...
Receiving Radio Broadcasts You can browse through all the stations or use the preset function to go immediately to a particular station. IMPORTANT: Using Preset Tuning When using the remote control, check to see if its AUDIO/ remote control mode selector is set to the correct TV/VCR Once a station is assigned to a channel number, the station can be position:...
To tune in a preset station Note: On the front panel: When using the FM MODE button on the remote control, be sure that the 10 keys are activated for the tuner, not for the CD and others. 1. Turn SOURCE SELECTOR to SOURCE SELECTOR (See page 43.) select the band (FM or AM).
Using the SEA Modes The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds. IMPORTANT: Creating Your Own SEA Mode When using the remote control, check to see if its AUDIO/ remote control mode selector is set to the correct TV/VCR You can adjust and store your own SEA adjustment into memory position:...
The 3D-PHONIC mode is the result the other hand, indirect sounds are delayed by the distances of the of research on sound localization technology carried out at JVC for ceiling and walls. These direct sounds and indirect sounds are the many years.
Dolby Following modes cannot be used when only the front speakers Surround (bearing the mark ) you can use JVC are connected to this receiver (without the rear speakers or DOLBY SURROUND Theater Surround.
Available DSP Modes According to the Speaker Arrangement Available DSP modes will vary depending on how many speakers are used with this receiver. Make sure that you have set the speaker information correctly (see page 14). Speaker arrangements Available DSP modes Each time you press DSP MODE on the front panel or SURROUND MODE on the remote control, the DSP modes change as follows: Front...
IMPORTANT: 3. Press EFFECT to select an effect EFFECT level you want. When using the remote control, check to see if its remote control mode selector is set to the correct AUDIO/ • Each time you press the button, the effect TV/VCR position: level changes as follows:...
3. Adjust the effect level. BALANCE/SURROUND Adjusting the Surround Modes ADJUST 1) Press (BALANCE/) SURROUND ADJUST repeatedly until “DSP Once you have adjusted the Surround modes, the adjustment is EFFECT” appears on the display. memorized for each Surround mode. The display changes to show the current setting.
Page 108
JVC Theater Surround adjustments 4. Adjust the speaker output levels. • To adjust the center speaker level, press CENTER –/+ (from Before you start, remember... –10 dB to +10 dB). • Make sure that you have set the speaker information correctly •...
DSP EFFECT 4 1. Press SURROUND ON/OFF so that the lamp on the front panel button lights up. As the number increases, JVC Theater Surround becomes • Each time you press the button, the Dolby/DTS/MPEG stronger. Surround turns on and off alternately.
Page 110
• Each time you press the button, the DSP modes change. (See page 23 for more details.) 2. Select and play a sound source. • To enjoy 3D-PHONIC and JVC Theater Surround, play back a software encoded with Dolby Surround and labeled with mark. DOLBY SURROUND...
Using the DVD MULTI Playback Mode This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Before playing back a DVD, refer also to the manual supplied with the DVD player. From the remote control: IMPORTANT: DVD MUILTI...
Using the On-Screen Menus You can use the Menus on the TV screen to control the receiver. To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 7), and set the TV’s input mode to the proper position to which the receiver is connected.
Adjusting the Front Speaker Output Balance Adjusting the Subwoofer Output Level (Also see page 13) (Also see page 12) 1. Press MENU. 1. Press MENU. The MAIN MENU appears on the TV. The MAIN MENU appears on the TV. • Pressing one of the % / fi / @ / # buttons also displays the •...
CONTROL,” then press @ / #. “REAR R LEVEL”: Adjust the right rear speaker output level. * The SOUND CONTROL menu appears. For JVC Theater Surround: 3. Press % / fi to move “TEST TONE”: Output a test tone. to “SEA,” then press @ “CENTER LEVEL”: Adjust the center speaker output...
4. Press % / fi to move “LFE ATT.”: Set the low frequency effect attenuator level (see page 15). to “SEA ADJUST.” “COMP.”: Set the dynamic range compression The SEA ADJUST menu (see page 15). appears. “DIGITAL 1/2/3”: Set the digital input terminals 5.
6. Press % / fi to move Storing the Preset Stations (Also see page 18) to “PRESET NAME,” 1. Press MENU. then press SET. The MAIN MENU appears on the TV. • Pressing one of the % / fi / @ / # buttons also displays the The character entry screen appears.
COMPU LINK Remote Control System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver. Automatic Power On/Off (Standby): only possible To use this remote control system, you need to connect JVC audio...
TEXT COMPU LINK Remote Control System The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD Text and MDs. Using these information in the discs, you can operate the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system through the receiver.
1 Source name: CD or MD OPERATIONS 2 Select , then press SET to change the disc. 3 Track numbers and track titles. To use this remote control system, you need to connect the TV to the • The current playing (selected) track is indicated in MONITOR OUT jack on the rear panel (see page 7), and set the yellow.
Search for a disc by its disc title: Searching for a Disc (Only for the CD player) 1. Press TEXT DISPLAY while “CD” is selected as Search for a disc by its performer: the source. 1. Press TEXT DISPLAY while “CD” is selected as The Disc Information screen appears on the TV.
Search for a disc by its genre: Entering the Disc Information 1. Press TEXT DISPLAY while “CD” is selected as For the CD Player with the disc memory function: the source. You can use the disc memory function through this receiver. The Disc Information screen appears on the TV.
Page 122
For the MD recorder: 4. Repeat step 3 until you finish putting a You can write the disc information (disc title and song titles) into the disc. You can only write the song title for the song currently performer name (up to selected.
AV COMPU LINK Remote Control System The AV COMPU LINK remote control system allows you to operate JVC video components (TV, VCR, and DVD player) through the receiver. To use this remote control system, you need to connect the video components you want to operate, following the diagrams below and the procedure on the next page.
Page 124
One-Touch DVD Play 1. If you have already plugged your VCR, DVD player, TV, and this receiver into the AC outlets, Simply by starting playback on the DVD player, you can enjoy the unplug their AC power cords first. DVD playback without setting other switches manually. •...
Operating JVC’s Audio/Video Components You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control. Tuner Operating Audio Components You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):...
Page 126
Cassette deck CD player-changer After pressing CD-DISC (with the remote control mode selector set After pressing TAPE/MD or TAPE/MD CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can to “AUDIO/TV/VCR”), you can perform the following operations perform the following operations on a cassette deck: on a CD player-changer: PLAY: PLAY:...
RCA pin plugs (see pages 6 following operations on the VCR: and 7). • Some JVC VCRs can accept two types of the control signals 1 – 9, 0: Selects the TV channels on VCR. PLAY: —...
4. Enter manufacturer’s code (three digits) using buttons 1 – 9, and 0. See the list on pages 48 and 49 to find the code. Examples: For a JVC product, press 0, 3, then 6. For a Sony product, press 0, 0, then 0. TV/CATV/DBS...
Page 129
See the list on pages 50 and 51 to find the code. Examples: For a Toshiba product, press 0, 0, then 0. Examples: For a JVC product, press 0, 0, then 8. For a Samsung product, press 7, 0, then 2.
Page 130
Manufacturers’ codes for TV Finlux -Mark Firstline 009, 216 Acura Fisher 154, 208 Admiral Formenti Aiko Fortress Akai 030, 208 Frontech Akura Funai 264, 342 Alaron 047, 093, 178, 451 Alba 009, 036, 037 Amstrad 009, 037 Geloso Anam 003, 004, 009, 068, 161, 250, 425, 426 General Anam National 161, 250, 425...
Troubleshooting Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center. PROBLEM POSSIBLE CAUSE SOLUTION The power cord is not plugged in. The display does not light up.
Specifications Amplifier Output Power At Stereo operation: 100 W* per channel, min. RMS, both channels driven into 8 Ω at Front channels: 1 kHz with no more than 0.9% total harmonic distortion. (IEC268-3/DIN) At Surround operation: 100 W* per channel, min. RMS, driven into 8 Ω at 1 kHz with no Front channels: more than 0.8% total harmonic distortion.
Page 136
FM tuner (IHF) Tuning Range: 87.50 MHz to 108.00 MHz 12.8 dBf (1.2 µV/75 Ω) Usable Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 Ω) 50 dB Quieting Sensitivity: Monaural: 41.3 dBf (31.5 µV/75 Ω) Stereo: Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf Stereo: 73 dB at 85 dBf Total Harmonic Distortion:...
Page 137
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.) Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido) Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.U.A., o Canadá, a Austrália e o Reino Unido) VOLTAGE SELECTOR 110V...