Specifications - Crown I-Tech HD Series Operation Manual

5 Troubleshooting
CONDITION: No sound, even though
the amp has power. Power LED is on
with out flashing and the amp is receiving an input
sig nal. Signal indicator is on or flashing.
POSSIBLE REASON
• Speakers not connected.
• Open circuit due to speaker failure.
• There is a short on the amplifier output. First
disconnect your speakers from the affected
channel(s) one by one to determine if one of
the loads is shorted.
• Ready LED is off. Channel has been set to
standby mode via the software.
• Amplifier is in blackout mode. Press or
turn an Encoder to reactivate the LCD
display.
CONDITION: No input signal. Signal
indicator is not flashing even though audio is
applied, and the channel is ready.
POSSIBLE REASON
• Input signal level is very low.
• Another source is selected or routed.
page 40
I-Tech HD Series Power Amplifiers
CONDITION: Data indicator not flash­
ing, even though host computer
software is active.
POSSIBLE REASON:
• Cable between computer and amplifier is broken
or not connected.
Note: Data indicator flashes only when the amplifier
is polled for data, or is polled to see whether it is
online.
CONDITION: Yellow LINK ACTIVITY indicator in
Ethernet connector does not illuminate or flash.
POSSIBLE REASON:
• Ethernet link is broken.
CONDITION: COND indicator is off.
POSSIBLE REASON:
• There is only one conductor allowed per network system. This
indicator is lit only when the amplifier is the conductor.
• Amplifier is in blackout mode. Press or turn an Encoder to
reactivate the LCD display.
CONDITION: Computer does not communicate with the
network devices.
POSSIBLE REASON:
• Incorrect wiring. See Section 3.5 letter O on network wiring.
• IP Addressing is not done correctly. Use the Network Troubleshooting
Wizard in System Architect.
Operation Manual
I-Tech HD Series Power Amplifiers

6 Specifications

Minimum guaranteed Power
20 Hz - 20 kHz with 0.35% THD
Stereo, 2 ohms (per ch.)
Stereo, 4 ohms (per ch.)
Stereo, 8 ohms (per ch.)
Bridge mono, 4 ohms
Bridge mono, 8 ohms
Performance
Input Sensitivity (volts RMS) for rated output
Voltage Gain for full rated power at 8 ohms
Frequency Response (at 1 watt, 20Hz - 20 kHz)
Signal to Noise Ratio below rated full-bandwidth power, A-weighted
Total Harmonic Distortion (THD) at full rated power at 1 kHz
Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1,
from full rated output to –35 dB
Maximum Input Level +15 dBu or +21 dBu, depending on setting of
Latency 1.16 mS at 48 kHz, 529 µS at 96 kHz
A/D, D/A Converters
Digital Input
Onboard sample rate converter.
Network Onboard HiQnet and TCP/IQ, compatible with
standard 100Mb Ethernet hardware
DSP 24-bit conversion with 32-bit, floating-
Attenuators Speed-sensitive rotary encoders, 0.5 dB
Operation Manual
I-T5000HD I-T9000HD
1800W 2500W
2000W 3000W
1250W 1500W
3600W 5000W
4000W 6000W
I-T5000HD I-T9000HD
Adjustable in 0.1V steps from Adjustable in 0.1V steps from Adjustable in 0.1V steps from
1.28V to 8V 1.28V to 8V
37.1 dB to 22.2 dB 37.9 dB to 23.0 dB
± 0.25 dB ± 0.25 dB
> 108 dB > 108 dB
< 0.1% < 0.1%
< 0.35% < 0.35%
+15 dBu or +21 dBu, +15 dBu or +21 dBu,
maximum input level depending on setting of maximum input level depending on setting of maximum input level
1.16 mS at 48 kHz, 529 µS at 96 kHz 1.16 mS at 48 kHz, 529 µS at 96 kHz
24-bit 96 kHz Cirrus Logic 24-bit 96 kHz Cirrus Logic 24-bit 96 kHz Cirrus Logic
AES/EBU, 24-bit, 32-96 kHz. AES/EBU, 24-bit, 32-96 kHz. AES/EBU, 24-bit, 32-96 kHz.
Onboard sample rate converter. Onboard sample rate converter.
Onboard HiQnet and TCP/IQ, compatible with Onboard HiQnet and TCP/IQ, compatible with
standard 100Mb Ethernet hardware standard 100Mb Ethernet hardware
24-bit conversion with 32-bit, floating- 24-bit conversion with 32-bit, floating-
point DSP processing point DSP processing point DSP processing
Speed-sensitive rotary encoders, 0.5 dB Speed-sensitive rotary encoders, 0.5 dB
steps, range 0 to –100 dB. steps, range 0 to –100 dB steps, range 0 to –100 dB
I-T12000HD
3500W
4000W
2100W
7000W
8000W
I-T12000HD
1.28V to 8V
40.1 dB to 24.5 dB
± 0.25 dB
> 108 dB
< 0.1%
< 0.35%
page 41