Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Blodgett XCEL-50EC
Summary of Contents for Blodgett XCEL-50EC
- Page 1 XCEL 50EC HALF SIZE ELECTRIC CONVECTION OVEN INSTALLATION - OPERATION - MAINTENANCE BLODGETT OVEN COMPANY www.blodgett.com 44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658 6600 Fax: (802)864 0183 PN 52137 Rev D (11/12) E 2012 - G.S. Blodgett Corporation...
- Page 2 IMPORTANT WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE IN STALLATION, OPERATING AND MAINTENANCE IN STRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
- Page 3 THE REPUTATION YOU CAN COUNT ON For over a century and a half, The Blodgett Oven Company has been building ovens and nothing but ovens. We've set the industry's quality standard for all kinds of ovens for every foodservice operation regardless of size, application or budget.
- Page 4 Model: Your Service Agency's Address: Serial Number: Your oven was installed by: Your oven's installation was checked by:...
-
Page 5: Table Of Contents
Table of Contents Introduction Oven Description and Specifications ....... . Installation Oven Location . -
Page 6: Introduction
Introduction Oven Description and Specifications Cooking in a convection oven differs from cooking Blodgett convection ovens represent the latest ad in a conventional deck or range oven since heated vancement in energy efficiency, reliability, and air is constantly recirculated over the product by ease of operation. -
Page 7: Installation
Installation Oven Location The well planned and proper placement of your ADJUSTMENTS ASSOCIATED WITH INITIAL oven will result in long term operator convenience INSTALLATION and satisfactory performance. Each oven, and its component parts, have been The XCEL 50EC requires 0" (0 cm) clearances be thoroughly tested and inspected prior to ship tween the oven sides and back and any combus ment. -
Page 8: Utility Connections
Blodgett oven, please contact ERATOR. your local distributor. If you do not have a local dis tributor, please call the Blodgett Oven Company at Qualified installation personnel are individuals, a 0011 802 860 3700. firm, a corporation, or a company which either in... -
Page 9: Delivery And Inspection
Installation Delivery and Inspection All Blodgett ovens are shipped in containers to Crate #2 prevent damage. Upon delivery of your new oven: The second crate contains: Inspect the shipping container for external dam Oven stand age. Any evidence of damage should be noted... -
Page 10: Oven Assembly
Installation Oven Assembly OVEN ASSEMBLY TO STAND 7. Position the stand below the oven. Be sure the support arms on the stand are on the right NOTE: The oven weighs approximately 350 lbs, side when facing the front of the oven. Place we recommend using either a fork truck or the oven flush with the front of the stand and genie lift to raise the oven. -
Page 11: Stand Accessories
Installation Oven Assembly OVEN LEVELING 1. Place a level on top of the oven. Loosen the set screws on the side of each caster. Turn the adjustment collar clockwise to raise and counter clockwise to lower the oven. 2. When the oven is level, tighten the casters by turning the two set screws on the side of each caster assembly. -
Page 12: Drain Assembly
Installation Oven Assembly DRAIN ASSEMBLY 5. Remove the hardware bag shipped inside the drain actuator. 1. Smear the threads of the drain pipe with pipe 6. Remove the actuator tab bracket holding the dope. actuator arm. See Figure 7. 2. Install the drain pipe using a pipe wrench. Be sure to align the actuator mounting bracket with the side of the oven. - Page 13 Installation Oven Assembly 8. Slide the studs on the back of the actuator box port bracket, found in the hardware bag, on into the holes in the actuator bracket on the top of the actuator box. Secure the bracket drain pipe. with the tie wraps provided.
-
Page 14: Cleaning System Connection
Installation Oven Assembly 15. Install the hose clamp, previously attached to CLEANING SYSTEM CONNECTION the actuator cover, around the plastic cleaning 1. Secure the hose to the cleaning fitting on the solution hose. back of the oven with the clamp provided. NOTE: Be sure there are no kinks in the clean ing solution hose. -
Page 15: Misc Parts
Installation Oven Assembly MISC PARTS INSTALLING DRAIN HOSE 1. If the drain cap is connected, lift up on the two Oven Vent Pan and Cover rings to remove the cap. 1. Install the oven vent cover using the hardware 2. Connect the drain hose to the oven drain. Pull provided. -
Page 16: Operation
Operation IQ Vision Control THE INFORMATION CONTAINED IN THIS SEC TION IS PROVIDED FOR THE USE OF QUALIFIED OPERATING PERSONNEL. QUALIFIED OPERAT ING PERSONNEL ARE THOSE WHO HAVE CAREFULLY READ THE INFORMATION CON TAINED IN THIS MANUAL, ARE FAMILIAR WITH THE FUNCTIONS OF THE OVEN AND/OR HAVE HAD PREVIOUS EXPERIENCE WITH THE OP ERATION OF THE EQUIPMENT DESCRIBED. -
Page 17: Operational Test Procedure
Operation IQ Vision Control OPERATIONAL TEST PROCEDURE Plug oven into electrical source NOTE: This scrolling can be bypassed by pressing SCAN. The controller will scroll through the following: 1.) Appliance Type 2.) Software # 3.) Download # 4.) SCK Address 5.) PREHEAT"... -
Page 18: Troubleshooting
Operation Troubleshooting ERROR CODE DESCRIPTION ACTION FAN ERROR" or Problem with the blower Turn oven off for 30 seconds FAN DRIVE ERROR" and then back on. If the er ror repeats, call for service "ERROR" Problem with door Call for service "STRIKE SWITCH"... - Page 19 Operation Troubleshooting ERROR CODE DESCRIPTION ACTION "HEAT ERROR CALL FOR oven temperature Call for service. SERVICE" doesn't rise from 150F to 300F within 5 minutes. Problem with the heating elements. "COMM ERROR CALL FOR If the controller has lost com Call for service.
- Page 20 SCKR Link Software, or any part of, from pliance purchased from the BLODGETT OVEN unauthorized use or disclosure. COMPANY (COMPANY"). The SCKR Link Soft 5.
- Page 21 8. Limited Warranty: FAST WARRANTS THAT 10. No Liability for Consequential Damages: IN THE SCKR LINK SOFTWARE WILL, UNDER NO EVENT SHALL FAST BE LIABLE FOR ANY NORMAL AND ANTICIPATED USE, AND LOST OR ANTICIPATED PROFITS, OR ANY WHEN USED IN THE SPECIFIED OPERAT INCIDENTAL, EXEMPLARY, SPECIAL, OR ING CONDITIONS, BE FREE FROM MATERI CONSEQUENTIAL DAMAGES ARISING OUT...
Need help?
Do you have a question about the XCEL-50EC and is the answer not in the manual?
Questions and answers