Bosch GSH 5 CE Professional Original Instructions Manual page 8

OBJ_BUCH-430-010.book Page 8 Friday, November 27, 2015 10:56 AM
8 | English
The dust protection cap 1 largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
tool, take care that the dust protection cap 1 is not damaged.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Inserting (see figure B)
– Clean and lightly grease the shank end of the tool.
– Insert the tool in a twisting manner into the tool holder until
it latches itself.
– Check the latching by pulling the tool.
Removing (see figure C)
– Push back the locking sleeve 2 and remove the tool.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dusts can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
– To start the machine, press the On/Off switch 6 at the top
(I) until it locks.
– To switch off the machine, press the On/Off switch 6 at
the bottom (0) and release it.
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Setting the Speed/Impact Rate
The electronic control enables stepless speed and impact
preselection in accordance with the material to be worked.
1 609 92A 1U9 | (27.11.15)
The constant electronic control keeps the preselected speed
and impact rate nearly constant between no-load and load
conditions.
Select the speed with the thumbwheel 7 according to the ma-
terial.
When plugging the plug into the socket outlet or after a power
failure, the constant electronic control automatically sets the
highest speed and impact rate. This ensures working at opti-
mum performance despite too low preadjustment of the
thumbwheel 7.
The data in the following table are recommended values.
Application
Working roughcast/light building materials
Removing tiles
Working brick
Working concrete
Changing the Chiselling Position (Vario-Lock)
The chisel can be locked in 12 positions. In this manner, the
optimum working position can be set for each application.
– Insert the chisel into the tool holder.
– Push the chisel adjustment ring 3 forward and turn the
chisel to the required position with the chisel adjustment
ring 3.
– Release the chisel adjustment ring 3 and turn the chisel un-
til it latches.
Working Advice
 Before any work on the machine itself, pull the mains
plug.
Vibration Damper
The integrated vibration damper in the main handle and at the
hammer mechanism reduces occurring vibrations.
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Service Indicator 8
When the carbon brushes are worn out, the machine switches
itself off. This is indicated approx. 8 hours beforehand by the
lighting or blinking of the service indicator 8. The machine
must then be sent to an after-sales service agent. Addresses
Thumb-
wheel 7
Bosch Power Tools