Remote Control - Pioneer VSX-D510 Operating Instructions Manual

Displays & Controls

Remote Control

1
2
3
4
5
6
7
8
9
0
-
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the stated
mode.
For other equipment controls, see Controlling the
Rest of Your System on pages 31-32.
2 RECEIVER button (see page 13)
Use this button when setting up the surround sound
for the receiver.
3 NUMBER/MODE buttons (see pages 26, 31, 32)
Use the number buttons to select the radio frequency
in tuner DIRECT ACCESS mode or the tracks in CD,
DVD mode etc.
Also, buttons marked with the following names have
special functions. If you try to use one of these
functions but the display flashes it means that
function cannot be used in the current mode (for
example DSP modes cannot be used when 5.1 CH
setting is on).
2 (see pages 17, 25)
Use to put receiver in DOLBY DIGITAL, DOLBY
SURROUND and DTS modes. To use first press the
button then operate this button.
RECEIVER
20
En
Î
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
CD-R/
RECEIVER TUNER TV CONT
TAPE/MD
2
DSP MODE MIDNIGHT 5.1CH
1 2 3 4
CHANNEL TEST SIGNAL
ATT
SELECT TONE SELECT
5 6 7 8
CHANNEL
EFFECT
LEVEL
‡
9 0
ENTER
10 DISC
CH
FUNC
TV CONTROL
VOL VOL
FQ
ST ST
ENTER
TOP
MENU
MENU
FQ
SOURCE CLASS MPX BAND
7 8 3
D.ACCESS CHANNEL
1 ¡ 4 ¢
LOUDNESS FUNCTION MUTING
FL REMOTE MASTER
RECEIVER
DIMMER SETUP VOLUME
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
DSP mode (see pages 24)
Use to put receiver in one of the DSP modes. To use
first press the
button.
MIDNIGHT (see page 24)
Use to put receiver in MIDNIGHT mode. To use first
=
press the
RECEIVER
5.1 ch (see page 24)
When the DVD/LD or DVD 5.1 CH function is
selected each press switches the DVD/LD input
between DVD/LD and DVD 5.1 CH. To use first press
the
RECEIVER
CHANNEL SELECT (see page 17-memo)
Use to select a speaker when setting up the surround
~
sound of the receiver. To use first press the
RECEIVER
TEST TONE (see page 17)
Use to sound the TEST TONE when setting up the
!
surround sound of the receiver. To use first press the
RECEIVER
@
ATT
If the Overload indicator lights often, use to attenuate
#
(lower) the level of an analog input signal to prevent
$
distortion. To use, press the
then press this button.
%
CHANNEL LEVEL +/– (see page 17-memo)
Use to set up the levels of the surround sound of the
^
receiver. To use first press the
operate this button.
SIGNAL SELECT (see page 23)
Use to select the proper signal (analog, digital) for the
source your are inputting. To use first press the
RECEIVER
4 THE FOLLOWING FOUR SETS OF BUTTONS
ARE DEDICATED TV CONTROL. THEY ARE
ONLY USED FOR CONTROLLING YOUR TV.
FUNC button
Use select the TV function.
TV POWER button
Use to turn on the power of the TV.
TV CHANNEL +/–
Use to change channels on your TV.
TV VOLUME +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with your
DVD player.
6 SOURCE button
Use to turn on/off the components connected to the
receiver.
button then operate this
RECEIVER
button then operate this button.
button then operate this button.
button then operate this button.
button then operate this button.
RECEIVER
RECEIVER
button then operate this button.
buttons
button first,
button then