Pioneer VSX-818V-K Operating Instructions Manual page 41

The System Setup menu
2 Select CUSTOM1 or CUSTOM2 then use
to select the setting you want to
copy.
2d.EQ Data Copy
TO FROM
CUSTOM1 CUSTOM1
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
:Cancel
• You can also copy from one custom setting
to another. For more on the ALL CH
ADJUST and FRONT ALIGN settings, see
Setting the Acoustic Calibration EQ
automatically on page 40.
3 Select 'OK' to copy and confirm.
Setting the Acoustic Calibration EQ
manually
Before manually adjusting the Acoustic
Calibration EQ, we recommend copying the
ALL CH ADJUST or the FRONT ALIGN settings
from the auto setup above (or from
Automatically setting up for surround sound
(MCACC) on page 8) to one of the custom
settings. Instead of just a flat EQ curve, this will
give you a reference point from which to start
(see Copying your Acoustic Calibration EQ
settings on page 40 for how to do this).
1 Select 'EQ CUSTOM1 Adjust' or 'EQ
CUSTOM2 Adjust' from the Manual MCACC
setup menu.
2.Manual MCACC
a.Fine Ch Level
b.Fine SP Distance
c.EQ AUTO Setting
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
:Return
2 Select which method you would like to
use to adjust the overall frequency balance.
It is best to choose whichever one you copied
to the custom setting in Copying your Acoustic
Calibration EQ settings on page 40.
2d.EQ Data Copy
TO FROM
CUSTOM1 ALL CH ADJ
CUSTOM2 [ CUSTOM2 ]
Start Copy [ OK ]
:Cancel
2e.EQ CUSTOM1 Adjust
Test Tone Type
ALL CH ADJUST
ENTER:Next :Cancel
• ALL CH ADJUST – All the speakers can be
set independently so no special weighting
is given to any one channel. When
adjusting, test tones will sound for each
individual channel.
• FRONT ALIGN – Speakers are set in
accordance with the front speaker
settings. The sound of the test tone will
alternate between the left front (reference)
speaker and the target speaker.
3 Select the channel(s) you want and
adjust to your liking.
2e.EQ CUSTOM1 Adjust
Test Tone Type:
"ALL CH ADJUST"
Left
40Hz : [ +1.0dB]
125Hz : [ 0.0dB]
250Hz : [ 0.0dB]
4kHz : [ 0.0dB]
13kHz : [ 0.0dB]
TRIM : [ 0.0dB]
:Finish
Use to select the channel.
Use to select the frequency and
boost or cut the EQ. When you're finished, go
back to the top of the screen and use
select the next channel.
• The front speakers can't be adjusted if you
selected FRONT ALIGN.
• The OVER indicator shows in the display if
the frequency adjustment is too drastic
and might distort. If this happens, bring
the level down until OVER disappears
from the display.
Tip
• Changing the frequency curve of one
channel too drastically will affect the
overall balance. If the speaker balance
seems uneven, you can raise or lower
channel levels using test tones with the
TRIM feature. Use
then use to raise or lower the
channel level for the current speaker.
4 When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
2e. EQ CUSTOM1 Adjust
Test Tone Type:
"ALL CH ADJUST"
[ Left ]
40Hz : +1.0dB
125Hz : [ 0.0dB]
250Hz : [ 0.0dB]
4kHz : [ 0.0dB]
13kHz : [ 0.0dB]
TRIM : [ 0.0dB]
:Finish
to
to
to select TRIM
06
41
En