Pioneer VSX-AX5Ai-G Operating Instructions Manual page 82

11 Advanced setup
3 Select the component that corresponds with the
one you connected to that input
Select between DVD/LD, TV/SAT, VCR1, VCR 2, CD,
CD-R or MD.
• Use the
do this.
• If you assign a digital input to a certain function (for
example, DVD/LD) then any digital inputs previously
assigned to that function will automatically be
switched off.
4 When you're finished, select 'Exit'.
You will return to the Input Assign menu.
Assigning the component video inputs
• Default settings:
Component-1 – OFF
Component-2 – OFF
If you used component video cables to connect your
video equipment you must tell the receiver which device
it is, or else you may see the S-video or composite video
input instead of the component video signal.
1 Select 'Component-In Select' from the Input
Assign menu.
3. Input Assign
[Digital-In Select
[Component-In Select
[i.LINK Input
[Exit
2 Select the number of the component video input
to which you've connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3 Select the component that corresponds with the
one you connected to that input.
• Use the
do this.
• If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver's component video
MONITOR output.
4 When you're finished, select 'Exit'.
You will return to the Input Assign menu.
82
En
(cursor up/down) buttons and ENTER to
Component - In Select
Component - 1 [
Component - 2 [
]
[ Exit ]
]
]
]
Component - In Select
Component - 1 [ DVD/LD ]
Component - 2 [ OFF ]
[ Exit ]
(cursor up/down) buttons and ENTER to
Assigning the i.LINK inputs
If you assign i.LINK-equipped components to an input
(for example DVD/LD), you will be able to select both
audio and video signals from i.LINK-equipped
components using the corresponding MULTI CONTROL
button (or MULTI JOG dial on the front panel).
1 Select 'i.LINK Input' from the Input Assign menu.
If no i.LINK-equipped components are connected i.LINK
Input cannot be selected.
2 Select an i.LINK-equipped component.
When a number of i.LINK-equipped components are
connected to your receiver, the i.LINK-equipped
component you are looking for might be listed on
additional display screens.
• i.LINK is displayed after unassigned device names
(e.g. DV-868AVi [i.LINK]).
• If a connected devices cannot output (playback) a
source using the i.LINK connection, [- - - -] is
displayed after the input device name (e.g. DV-
OFF ]
868AVi [- - - -]). Non-compatible devices cannot be
OFF ]
assigned to inputs.
• When the cables for an assigned input device
become loose or the power is cut to the device, an
asterisk (*) appears before the device name (e.g.
*DV-868AVi [DVD/LD]).
3 Select the component that you want to assign.
Use the
i.LINK Input
1 DV - 868AVi [
[ Exit ]
When you assign an i.LINK-equipped video component,
select the input source to which you have connected the
video signal from the component.
• If you assign an i.LINK input to a certain function (for
example DVD/LD) then any digital inputs previously
assigned to that function will automatically be set to
i.LINK (not assigned).
• TUNER, PHONO and USB inputs cannot be
assigned.
4 When you're finished, select 'Exit'.
You will return to the Input Assign menu.
3. Input Assign
[Digital-In Select ]
[Component-In Select ]
[i.LINK Input ]
[Exit ]
(cursor up/down) buttons and ENTER.
i.LINK Input
i.LINK ] 1 DV - 868AVi [
[ Exit ]
DVD/LD ]