Table of Contents
Advertisement
12
Controlling the rest of your system
Chapter 12:
Controlling the rest of your system
Setting the remote to control other
components
Most components can be assigned to one of the input
source buttons (such as DVD or CD) using the
component's manufacturer preset code stored in the
remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
Note
• You can cancel or exit any of the steps by pressing
RECEIVER. To go back a step, press RETURN.
• After one minute of inactivity, the remote
automatically exits the operation.
Selecting preset codes directly
RECEIVER
DVD
DVD
BD
BD
DVR 1
DVR 1
DVR 2
DVR 2
FM/AM
XM
INPUT
SELECT
1
1
GENRE
4
4
SR+
7
7
D.ACCESS
1
While pressing the RECEIVER button, press SETUP.
The indicator on the remote control blinks.
2
Press the input source button for the component
you want to control.
When assigning preset codes to TV CONTROL, press TV
CTRL here.
The indicator lights up.
Note
1 You can't assign the RECEIVER, FM/AM, iPod USB, XM or SIRIUS buttons.
78
En
ST
ENTER
SOURCE
SOURCE
CATEGORY
RETURN
SETUP
SETUP
TUNE
TV
TV
HDMI
HDMI
iPod CTRL
CD
CD
CD-R
CD-R
AUTO/
STEREO/
BD MENU
DIRECT
A.L.C.
STANDARD
ADV SURR
HDD
DVD
SIRIUS
iPod USB
THX
STATUS
PHASE
DIMMER
ANT
MPX
SIGNAL SEL
2
2
3
3
MCACC
SLEEP
AUDIO
DISPLAY
CH
5
5
6
6
SBch
A.ATT
TV CTRL
TV CTRL
RECEIVER
RECEIVER
8
8
9
9
CH LEVEL
CLASS
0
0
ENTER
MASTER
INPUT
VOLUME
O
1
3
Use the number buttons to enter the 3 digit preset
code (see below).
The indicator blinks for half a second after you input each
digit and shows a long, two second blink once you have
entered a valid code. If the LED blinks three times, it
means an invalid code has been input or an error has
occurred.
4
Repeat steps 1 through 3 for the other components
you want to control.
5
When you're done, press RECEIVER.
To try out the remote control, switch the component on or
off (into standby) by pressing SOURCE. If it doesn't
seem to work, select the next code from the list (if there
is one).
Preset code list
You should have no problem controlling a component if
you find the manufacturer in this list, but please note that
there are cases where codes for the manufacturer in the
list will not work for the model that you are using. There
are also cases where only certain functions may be
ST
controllable after assigning the proper preset code.
DVD
Manufacturer Code
AKAI 007
DENON 003, 010
GOLDSTAR 014
HITACHI 012
JVC 004
LOEWE 013
MEM
MICROSOFT 017 (video game)
PANASONIC 003, 019
PHILIPS 013
PIONEER 000, 003, 009, 018, 020,
021 (BDP), 023 (BDP)
RCA 008, 011
SAMSUNG 005
SHARP 006
SONY 002, 016 (video game)
THOMSON 015
TOSHIBA 001, 022 (HD DVD)
ZENITH 014
LD
Manufacturer Code
KENWOOD 103
MITSUBISHI 100
PANASONIC 105, 106
PHILIPS 104
PIONEER 100, 111
RCA 107
SONY 101
SAT
Manufacturer Code
BELL 208
ECHOSTAR 205
PIONEER 200, 210
PRIMESTAR 206
RCA 201, 203, 209
SONY 202
CD
Manufacturer Code
California Audio labs 304
DENON 309
JVC 303
KENWOOD 310, 311, 321
KODAK 322
MARANTZ 304, 312, 323, 324
MCS 304
MEMOREX 300
NAD 316
ONKYO 307, 308, 320
OPTIMUS 300
PANASONIC 304, 326
PHILIPS 312, 322
PIONEER 300, 348 (SACD)
QUASAR 304
RCA 302, 313, 319
SANYO 313
SONY 301, 316, 317, 318
TEAC 305, 306, 324, 325, 327
THOMSON 319
YAMAHA 314, 315, 328
Advertisement
Table of Contents
