Page 1 Grand Cherokee 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 ROLLOVER WARNING .....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
When it comes to service, remember that your authorized dealer knows your Jeep® vehicle best, has factory-trained Always observe federal, state, provincial, and local laws technicians and genuine MOPAR® parts, and cares about wherever you drive.
Page 7: How To Use This Manual
INTRODUCTION HOW TO USE THIS MANUAL The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Essential Information Symbols Consult the Table of Contents to determine which section contains the information you desire. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Since the specification of your vehicle depends on the items...
Page 8: Rollover Warning
6 INTRODUCTION ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications.
Page 9: Warnings And Cautions
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 11 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12: Front View
10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Wheels/Tires 2 — Windshield 5 — Exterior Mirrors 3 — Headlights 6 — Doors...
Page 13: Rear View
GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 14: Instrument Panel
12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Multifunction Lever 5 — Paddle Shifter 3 — Steering Wheel 6 — Glove Compartment...
Page 15: Interior
GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior Features 1 — Power Window Switches 4 — Switch Panel 2 — Seats 5 — Climate Controls 3 — Transmission Gear Selector 6 — Radio...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .20 SENTRY KEY .
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Keyless Enter-N-Go — Passive Entry ..37 ▫ Tilt/Telescoping Steering Column ... .62 ▫ Automatic Unlock Doors On Exit ... .41 ▫...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Automatic Headlights — If Equipped ..72 ▫ Courtesy Lights ......76 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Wind Buffeting ......97 ▫ Venting Sunroof — Express ....104 POWER SUNROOF —...
Page 21 GETTING TO KNOW YOUR VEHICLE 19 ▫ Security ......118 ▫ Cupholders ......124 ▫...
Page 22: Keys
20 GETTING TO KNOW YOUR VEHICLE KEYS Key Fob The key fob allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a handheld key fob. The key fob does not need to be pointed at the vehicle to activate the system.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 1st Push Of Key Fob Unlock Button If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” located in “Doors” This feature lets you program the system to unlock either in “Getting To Know Your Vehicle”...
Page 24: Getting To Know Your Vehicle 15
22 GETTING TO KNOW YOUR VEHICLE 1. Remove the emergency key by sliding the mechanical 2. Separate the key fob halves using the tip of the emer- latch on the back of the key fob sideways with your gency key, a #2 flat blade screwdriver, or a coin and thumb and pull the emergency key out with your other gently pry the two halves of the key fob apart.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Separating Case With A Coin Key Fob Battery Replacement 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery.
Page 26 24 GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fobs General Information Programming the key fob may be performed by an autho- The following regulatory statement applies to all radio rized dealer. frequency (RF) devices equipped in this vehicle: Request For Additional Key Fobs This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 27: Ignition Switch
GETTING TO KNOW YOUR VEHICLE 25 IGNITION SWITCH Keyless Enter-N-Go — Ignition This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The Keyless Push Button Ignition has four operating modes which are labeled and will illuminate when in position.
Page 28: Vehicle On Message
26 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Driving position. • Do not leave children or animals inside parked • All the electrical devices are available. vehicles in hot weather. Interior heat build-up may cause serious injury or death. START •...
Page 29 GETTING TO KNOW YOUR VEHICLE 27 NOTE: The power window switches and power sunroof (if WARNING! (Continued) equipped) will remain active up to ten minutes after the • Do not leave the key fob in or near the vehicle, or in ignition is cycled to the OFF position.
Page 30: Remote Starting System - If Equipped
28 GETTING TO KNOW YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED WARNING! • Do not start or run an engine in a closed garage or This system uses the key fob to start the engine confined area. Exhaust gas contains Carbon Monox- conveniently from outside the vehicle while still ide (CO) which is odorless and colorless.
Page 31: Remote Start Abort Message
GETTING TO KNOW YOUR VEHICLE 29 All of the following conditions must be met before the WARNING! engine will remote start: • Do not start or run an engine in a closed garage or • Gear Selector in PARK confined area. Exhaust gas contains Carbon Monox- •...
Page 32: To Enter Remote Start Mode
30 GETTING TO KNOW YOUR VEHICLE To Exit Remote Start Mode Without Driving The The instrument cluster display message stays active until Vehicle the ignition is turned to the ON/RUN position. Push and release the Remote Start button one time or allow To Enter Remote Start Mode the remote start cycle to complete the entire 15-minute Push and release the Remote Start button on the key fob...
Page 33: Comfort Systems - If Equipped
GETTING TO KNOW YOUR VEHICLE 31 Comfort Systems — If Equipped 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- When Remote Start is activated, Auto-Comfort will work tion. anytime the temperature conditions are correct. When the feature is enabled, regardless of Remote Start or regular NOTE: Changes or modifications not expressly approved keyless start, the driver heated seat features will automati-...
Page 34: Customer Key Programming
32 GETTING TO KNOW YOUR VEHICLE Customer Key Programming After turning the ignition switch to the ON/RUN position, the vehicle security light will turn on for three seconds for Programming key fobs may be performed at an authorized a bulb check. If the light remains on after the bulb check, it dealer.
Page 35: Irregular Operation
GETTING TO KNOW YOUR VEHICLE 33 Irregular Operation If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it The system uses a key fob, an Ignition Node Module, indicates that there is a fault in the electronics. Should this Keyless Push Button Ignition and a RF receiver to prevent occur, have the vehicle serviced as soon as possible by an unauthorized vehicle operation.
Page 36: Vehicle Security Alarm - If Equipped
34 GETTING TO KNOW YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED 2. Perform one of the following methods to lock the vehicle: The vehicle security alarm monitors the vehicle doors, • Push the lock button on the interior power door lock hood, liftgate, and the Keyless Enter-N-Go —...
Page 37: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 35 Rearming Of The System NOTE: • The driver’s door key cylinder and the liftgate button on the If something triggers the alarm, and no action is taken to key fob cannot arm or disarm the vehicle security alarm. disarm it, the vehicle security alarm will turn the horn off after approximately 90 seconds, and then the vehicle •...
Page 38: Doors
36 GETTING TO KNOW YOUR VEHICLE DOORS WARNING! (Continued) Manual Door Locks • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to The power door locks can be manually locked from inside be in a vehicle unattended is dangerous for a number the vehicle by using the door lock knob.
Page 39: Keyless Enter-N-Go - Passive Entry
GETTING TO KNOW YOUR VEHICLE 37 Keyless Enter-N-Go — Passive Entry The Passive Entry system is an enhancement to the vehi- cle’s key fob and a feature of Keyless Enter-N-Go — Passive Entry. This feature allows you to lock and unlock the vehicle’s door(s) and fuel door without having to push the key fob lock or unlock buttons.
Page 40 38 GETTING TO KNOW YOUR VEHICLE To Unlock From The Driver Side To Unlock From The Passenger Side With a valid Passive Entry key fob within 5 ft (1.5 m) of the With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver’s door handle, grab the front driver door handle to passenger door handle, grab the front passenger door unlock the driver’s door automatically.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 • A lock request is made by the door panel switch while To Lock The Vehicle’s Doors And Liftgate the door is open. With one of the vehicle’s Passive Entry key fob within 5 ft •...
Page 42 40 GETTING TO KNOW YOUR VEHICLE • If Passive Entry is disabled using Uconnect System, the NOTE: DO NOT grab the door handle, when pushing the door handle lock button. This could unlock the door(s). key protection described in Preventing Inadvertent Locking of Passive Entry Key Fob in Vehicle remains active/functional.
Page 43: Automatic Unlock Doors On Exit
GETTING TO KNOW YOUR VEHICLE 41 Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. All doors are closed. 3. The transmission gear selector was not in PARK, then is placed in PARK.
Page 44 42 GETTING TO KNOW YOUR VEHICLE • After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • For emergency exit with the system engaged, pull up on the door lock knob (unlocked position), roll down the window, and open the door with the outside door handle.
Page 45: Seats
GETTING TO KNOW YOUR VEHICLE 43 SEATS Manual Adjustment (Front Seats) Seats are a part of the Occupant Restraint System of the WARNING! vehicle. • Adjusting a seat while the vehicle is moving is WARNING! dangerous. The sudden movement of the seat could cause you to lose control.
Page 46 44 GETTING TO KNOW YOUR VEHICLE Manual Front Seats Forward/Rearward Adjustment WARNING! Some models may be equipped with a manual front • Adjusting a seat while driving may be dangerous. passenger seat. The seat can be adjusted forward or rear- Moving a seat while driving could result in loss of ward by using a bar located by the front of the seat cushion, control which could cause a collision and serious...
Page 47 GETTING TO KNOW YOUR VEHICLE 45 Front Passenger Seat Fold-Flat Feature — If Equipped To fold the seatback to the flat load-floor position, lift the recline lever and push the seatback forward. To return to the seating position, raise the seatback and lock it into place.
Page 48: Manual Adjustment (Rear Seats)
46 GETTING TO KNOW YOUR VEHICLE desired position. To return the seatback, lift the lever, lean WARNING! forward and release the lever. • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 49: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 47 Power Adjustment (Front Seats) — If Equipped Adjusting The Seat Forward Or Rearward Some models may be equipped with eight-way power The seat can be adjusted both forward and rearward. Push driver and front passenger seats. The power seat switches the seat switch forward or rearward.
Page 50 48 GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped WARNING! Vehicles equipped with power driver or passenger seats • Adjusting a seat while driving may be dangerous. may also be equipped with power lumbar. The power Moving a seat while driving could result in loss of lumbar switch is located on the outboard side of the power control which could cause a collision and serious seat.
Page 51: Driver Memory Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Driver Memory Seat — If Equipped This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, and power tilt and telescopic steering column (if equipped) and a set of desired radio station presets.
Page 52 50 GETTING TO KNOW YOUR VEHICLE 3. Push and release the set (S) button on the memory To program your key fobs, perform the following: switch. 1. Cycle the vehicle’s ignition to the OFF position. 4. Within five seconds, push and release either of the 2.
Page 53 GETTING TO KNOW YOUR VEHICLE 51 Memory Position Recall driver’s seat and steering column (if equipped) stop mov- ing. A delay of one second will occur before another recall NOTE: The vehicle must be in PARK to recall memory can be selected. positions.
Page 54: Heated Seats - If Equipped
52 GETTING TO KNOW YOUR VEHICLE Each stored memory setting will have an associated Easy WARNING! (Continued) Entry and Easy Exit position. • Do not place anything on the seat or seatback that NOTE: The Easy Entry/Exit feature is not enabled when insulates against heat, such as a blanket or cushion.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 If the HI-level setting is selected, the system will automati- WARNING! cally switch to LO-level after approximately 60 minutes of continuous operation. At that time, the display will change • Persons who are unable to feel pain to the skin from HI to LO, indicating the change.
Page 56 54 GETTING TO KNOW YOUR VEHICLE HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the number of indicator lights changes from two to one, indicating the change.
Page 57: Front Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 55 Front Ventilated Seats — If Equipped Vehicles Equipped With Remote Start Located in the seat cushion and seat back are fans that On models that are equipped with remote start, the venti- draw the air from the passenger compartment and move lated seats can be programmed to come on during a remote air through fine perforations in the seat cover to help keep start.
Page 58 56 GETTING TO KNOW YOUR VEHICLE 1. Pull upward on the release lever to release the seat. 2. Fold the rear seat completely forward. Rear Seat Release Rear Seat Folded NOTE: NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for •...
Page 59: To Raise Rear Seat
GETTING TO KNOW YOUR VEHICLE 57 To Raise Rear Seat HEAD RESTRAINTS Raise the rear seatback and lock it into place. If interference Head restraints are designed to reduce the risk of injury by from the cargo area prevents the seatback from fully restricting head movement in the event of a rear-impact.
Page 60: Supplemental Active Head Restraints - Front Seats
58 GETTING TO KNOW YOUR VEHICLE Supplemental Active Head Restraints — Front To raise the head restraint, pull upward on the head Seats restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push Active Head Restraints are passive, deployable compo- downward on the head restraint.
Page 61 GETTING TO KNOW YOUR VEHICLE 59 For comfort, the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 62: Head Restraints - Rear Seats
60 GETTING TO KNOW YOUR VEHICLE Head Restraints — Rear Seats WARNING! The head restraints on the outboard seats are not adjust- • ALL the head restraints MUST be reinstalled in the able. They automatically fold forward when the rear seat is vehicle to properly protect the occupants.
Page 63 GETTING TO KNOW YOUR VEHICLE 61 NOTE: The center head restraint can be adjusted when occupied, or removed for Child Seat Tethering. To remove the head restraint, raise it as far as it can go by pulling upward. Then, push the release button at the base of the post while pulling the head restraint upward.
Page 64: Steering Wheel
62 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. STEERING WHEEL Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.
Page 65: Power Tilt/Telescoping Steering Column - If Equipped
GETTING TO KNOW YOUR VEHICLE 63 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 66: Heated Steering Wheel - If Equipped
64 GETTING TO KNOW YOUR VEHICLE NOTE: The engine must be running for the heated steering WARNING! wheel to operate. Do not adjust the steering column while driving. Vehicles Equipped With Remote Start Adjusting the steering column while driving or driv- On models that are equipped with remote start, the heated ing with the steering column unlocked, could cause the steering wheel can be programmed to come on during a...
Page 67: Mirrors
GETTING TO KNOW YOUR VEHICLE 65 MIRRORS Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right Inside Day/Night Mirror — If Equipped for various drivers. The mirror should be adjusted to center The mirror head can be adjusted up, down, left, and right on the view through the rear window.
Page 68: Outside Mirrors
66 GETTING TO KNOW YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are.
Page 69: Outside Mirrors Folding Feature
GETTING TO KNOW YOUR VEHICLE 67 Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: • Full forward position • Full rearward position •...
Page 70: Tilt Side Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
68 GETTING TO KNOW YOUR VEHICLE Power Folding Outside Mirrors — If Equipped Heated Mirrors — If Equipped If equipped with power folding mirrors, they can be These mirrors are heated to melt frost or ice. This electrically folded rearward and unfolded into the drive feature will be activated whenever you turn on the position.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 NOTE: The Automatic Fold/Unfold Mirrors feature is not turned on when delivered from the factory. The Automatic Fold/Unfold Mirrors feature can be turned on and off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia”...
Page 72: Illuminated Vanity Mirrors
70 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirrors Sun Visor “Slide-On-Rod” Feature — If Equipped To access an illuminated vanity mirror, flip down one of the The sun visor “Slide-On-Rod” feature allows for additional visors. flexibility in positioning the sun visor to block out the sun. Lift the cover to reveal the mirror.
Page 73: Exterior Lights
GETTING TO KNOW YOUR VEHICLE 71 EXTERIOR LIGHTS light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to Headlight Switch the O (off) position. The headlight switch is located on the left side of the NOTE: instrument panel, next to the steering wheel.
Page 74: Automatic Headlights - If Equipped
72 GETTING TO KNOW YOUR VEHICLE Automatic Headlights — If Equipped Headlights On Automatically With Wipers This system automatically turns the headlights on or off If your vehicle is equipped with Automatic Headlights, it according to ambient light levels. To turn the system on, also has this customer-programmable feature.
Page 75: Headlight Delay
GETTING TO KNOW YOUR VEHICLE 73 Headlight Delay Daytime Running Lights — If Equipped To aid in your exit, your vehicle is equipped with a The Daytime Running Lights (low intensity) come on headlight delay that will leave the headlights on for whenever the engine is running, and the transmission is approximately up to 90 seconds.
Page 76: Fog Lights - If Equipped
74 GETTING TO KNOW YOUR VEHICLE Fog Lights — If Equipped Multifunction Lever The fog lights are turned on by rotating the headlight The multifunction lever is located on the left side of the switch to the parking light or headlight position and steering column.
Page 77: Lane Change Assist - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 Lane Change Assist — If Equipped NOTE: • The Automatic High Beam Headlamp Control can be Tap the lever up or down once, without moving beyond turned on or off using the Uconnect System. Refer to the detent, and the turn signal (right or left) will flash three “Uconnect Settings”...
Page 78: Interior Lights
76 GETTING TO KNOW YOUR VEHICLE Courtesy Lights NOTE: Battery saver mode is canceled if the ignition is The courtesy lights can be turned on by pushing the top If the headlights remain on while the ignition is cycled OFF, corner of the lens.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 Front Map/Reading Lights — If Equipped Each light can be turned on by pushing a switch on either side of the console. These buttons are backlit for night time The front map/reading lights are mounted in the overhead visibility.
Page 80 78 GETTING TO KNOW YOUR VEHICLE Dimmer Controls Ambient Light — If Equipped The brightness of the instrument panel lighting can be The overhead console is equipped with an ambient light regulated by rotating the dimmer control up (brighter) or feature.
Page 81: Windshield Wipers And Washers
GETTING TO KNOW YOUR VEHICLE 79 WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer controls are located on the multifunction lever on the left side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
Page 82 80 GETTING TO KNOW YOUR VEHICLE Intermittent Wiper System Windshield Washer Operation Use one of the four intermittent wiper settings when To use the washer, push on the end of the lever (toward the weather conditions make a single wiping cycle, with a steering wheel) and hold while spray is desired.
Page 83: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE 81 WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind- shield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 84 82 GETTING TO KNOW YOUR VEHICLE The sensitivity of the system can be adjusted with the The Rain Sensing system has protection features for the multifunction lever. Wiper delay position one is the least wiper blades and arms, and will not operate under the sensitive, and wiper delay position four is the most sensi- following conditions: tive.
Page 85: Rear Window Wiper/Washer
GETTING TO KNOW YOUR VEHICLE 83 Rear Window Wiper/Washer Rotating the center portion upward once more will activate the washer pump which will continue to The rear wiper/washer controls are located on the multi- operate as long as the switch is held. Upon release function lever on the left side of the steering column.
Page 86: Headlight Washers - If Equipped
84 GETTING TO KNOW YOUR VEHICLE HEADLIGHT WASHERS — IF EQUIPPED NOTE: After turning the ignition switch and headlights ON, the headlight washers will operate on the first spray of The multifunction lever operates the headlight washers the windshield washer and then every eleventh spray after when the ignition switch is in the ON position and the that.
Page 87 GETTING TO KNOW YOUR VEHICLE 85 Uconnect 5.0 Automatic Climate Controls...
Page 88 86 GETTING TO KNOW YOUR VEHICLE Uconnect 8.4/8.4 NAV Automatic Climate Controls...
Page 89 GETTING TO KNOW YOUR VEHICLE 87 Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 90 88 GETTING TO KNOW YOUR VEHICLE Icon Description AUTO Button Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto- matic modes. Refer to “Automatic Operation” for more information. Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode.
Page 91 GETTING TO KNOW YOUR VEHICLE 89 Icon Description SYNC Button Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica- tor is illuminated when this feature is enabled. SYNC is used to synchronize the passenger tem- perature setting with the driver temperature setting.
Page 92 90 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel out- lets and warmer air from the floor outlets.
Page 93 GETTING TO KNOW YOUR VEHICLE 91 NOTE: CAUTION! • If fog or mist appears on the windshield or side glass, Failure to follow these cautions can cause damage to select Defrost mode, and increase blower speed if the heating elements: needed.
Page 94: Automatic Temperature Control (Atc) - If Equipped
92 GETTING TO KNOW YOUR VEHICLE temperature control buttons. Once the desired tempera- Recirculation ture is displayed, the system will achieve and automati- When outside air contains smoke, odors, or high humidity, cally maintain that comfort level. or if rapid cooling is desired, you may wish to recirculate interior air by pressing the Recirculation control button.
Page 95: Operating Tips
GETTING TO KNOW YOUR VEHICLE 93 Manual Operation Override Winter Operation This system offers a full complement of manual override To ensure the best possible heater and defroster perfor- features. The AUTO symbol in the front ATC display will mance, make sure the engine cooling system is functioning be turned off when the system is being used in the manual properly and the proper amount, type, and concentration mode.
Page 96 94 GETTING TO KNOW YOUR VEHICLE Outside Air Intake Cabin Air Filter Make sure the air intake, located directly in front of the The climate control system filters out dust and pollen from windshield, is free of obstructions, such as leaves. Leaves the air.
Page 97: Windows
GETTING TO KNOW YOUR VEHICLE 95 WINDOWS NOTE: For vehicles equipped with the Uconnect, the power window switches will remain active for up to 10 Power Window Controls minutes after the ignition is cycled to the OFF position. The window controls on the driver’s door control all the Opening either front door will cancel this feature.
Page 98: Auto-Down Feature
96 GETTING TO KNOW YOUR VEHICLE Auto-Down Feature • Any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- The driver door power window switch and the passenger closure. If this happens, pull the switch lightly and hold door power window switches have an Auto-Down feature.
Page 99: Window Lockout Switch
GETTING TO KNOW YOUR VEHICLE 97 Window Lockout Switch Wind Buffeting The window lockout switch on the driver’s door trim panel Wind buffeting can be described as the perception of allows you to disable the window controls on the rear pressure on the ears or a helicopter-type sound in the ears.
Page 100: Power Sunroof - If Equipped
98 GETTING TO KNOW YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, or with visors on the overhead console. access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children.
Page 101: Opening Sunroof
GETTING TO KNOW YOUR VEHICLE 99 Opening Sunroof Manual Express To close the sunroof, push and hold the switch in the forward position. Any release of the switch will stop the Push the switch rearward and release it within one-half movement and the sunroof will remain in a partially closed second and the sunroof will open automatically from any condition until the sunroof switch is pushed again.
Page 102: Pinch Protect Feature
100 GETTING TO KNOW YOUR VEHICLE Pinch Protect Feature Ignition Off Operation This feature will detect an obstruction in the opening of the NOTE: sunroof during Express Close operation. If an obstruction • The power sunroof switch can remain active in Acces- in the path of the sunroof is detected, the sunroof will sory Delay for up to approximately ten minutes after the automatically retract.
Page 103: Commandview Sunroof With Power Shade - If Equipped
GETTING TO KNOW YOUR VEHICLE 101 4. Release the sunroof switch, then push forward and hold the switch again within 5 seconds to begin the relearn process. The sunroof will complete one full cycle and return to the Fully Closed position. NOTE: If the sunroof switch is released anytime during the relearn cycle, the procedure will need to be repeated starting from the first step.
Page 104: Opening Sunroof
102 GETTING TO KNOW YOUR VEHICLE Manual Mode WARNING! (Continued) To open the sunroof, push and hold the switch rearward. • In a collision, there is a greater risk of being thrown The sunroof will stop automatically at the comfort stop from a vehicle with an open sunroof.
Page 105: Opening Power Shade
GETTING TO KNOW YOUR VEHICLE 103 Closing Power Shade Manual Mode To close the sunroof, push and hold the switch in the Express forward position. Any release of the switch will stop the Push the switch forward and release it within one-half movement and the sunroof will remain in a partially closed second and the shade will close automatically from any condition until the sunroof switch is pushed again.
Page 106: Venting Sunroof - Express
104 GETTING TO KNOW YOUR VEHICLE Venting Sunroof — Express Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or Push and release the Vent button within one-half second partially open positions. This is a normal occurrence and and the sunroof will open to the vent position.
Page 107: Hood
GETTING TO KNOW YOUR VEHICLE 105 HOOD To Open The Hood To open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. Safety Latch Location To Close The Hood 1.
Page 108: Liftgate
106 GETTING TO KNOW YOUR VEHICLE To Unlock/Enter The Liftgate WARNING! The liftgate may be released in several ways: Be sure the hood is fully latched before driving your • Key fob vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
Page 109: Closing
GETTING TO KNOW YOUR VEHICLE 107 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passen- gers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Closing Grasp the liftgate closing handle and initiate lowering the liftgate.
Page 110: Power Liftgate - If Equipped
108 GETTING TO KNOW YOUR VEHICLE Power Liftgate — If Equipped WARNING! The power liftgate may also be opened or closed by During power operation, personal injury or cargo pushing the liftgate button located on the front overhead damage may occur. Ensure the liftgate travel path is console.
Page 111: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE 109 Cargo Area Features • If the electronic liftgate release is pushed while the power liftgate is closing, the liftgate will reverse to the Rechargeable Flashlight full open position. The rechargeable flashlight is mounted on the left side of •...
Page 112 110 GETTING TO KNOW YOUR VEHICLE To operate the flashlight, push the switch once for high, Cargo Storage Bins twice for low, and a third time to return to off. There are up to four removable storage bins located in the rear cargo area.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether strap (attached to the bottom of the load floor) to the liftgate opening. Rear Lower Storage Bins Retractable Cargo Area Cover —...
Page 114 112 GETTING TO KNOW YOUR VEHICLE 3. The liftgate may be opened with the cargo cover in Rear Cargo Tie-Downs place. The rear cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving.
Page 115: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE 113 WARNING! WARNING! (Continued) • Place as much cargo as possible in front of the rear • To help protect against personal injury, passengers axle. Too much weight or improperly placed weight should not be seated in the rear cargo area. The rear over or behind the rear axle can cause the rear of the cargo space is intended for load carrying purposes vehicle to sway.
Page 116: Before You Begin Programming Homelink
114 GETTING TO KNOW YOUR VEHICLE To erase the channels, place the ignition in the ON/RUN position, and push and hold the two outside HomeLink buttons (I and III) for up to 20 seconds or until the orange indicator flashes. NOTE: •...
Page 117 GETTING TO KNOW YOUR VEHICLE 115 4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and then rapidly after HomeLink has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.
Page 118 116 GETTING TO KNOW YOUR VEHICLE To program the remaining two HomeLink buttons, repeat 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) each step for each remaining button. DO NOT erase the away from the HomeLink button you wish to program channels.
Page 119: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE 117 Reprogramming A Single HomeLink Button (Non- It may be helpful to unplug the device during the cycling Rolling Code) process to prevent possible overheating of the garage door or gate motor. To reprogram a channel that has been previously trained, follow these steps: 1.
Page 120: Using Homelink
118 GETTING TO KNOW YOUR VEHICLE Using HomeLink NOTE: • If the indicator light stays on constantly, programming To operate, push and release the programmed HomeLink is complete and the garage door/device should acti- button. Activation will now occur for the programmed vate when the HomeLink button is pushed.
Page 121: General Information
GETTING TO KNOW YOUR VEHICLE 119 • Push the LEARN button on the Garage Door Opener to WARNING! (Continued) complete the training for a Rolling Code. use a garage door opener without these safety fea- • Did you unplug the device for programming and re- tures.
Page 122: Internal Equipment
120 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT To open the glove compartment, pull the release handle. Storage Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Opened Glove Compartment Glove Compartment...
Page 123 GETTING TO KNOW YOUR VEHICLE 121 Door Storage Console Features Large storage areas are built into the door panels for easy The center console contains both an upper and a lower access. storage area. Door Panel Storage Storage Compartment...
Page 124 122 GETTING TO KNOW YOUR VEHICLE To open the upper storage compartment, pull upward on the small latch located on the lid. Lower Storage Compartment Your vehicle may have an optional CD or DVD player located in the center console. Storage Compartment Latches Lift upward on the larger of the latches to access the lower storage compartment.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Overhead Console The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink), power liftgate and power sunroof switches may also be included, if equipped. Lower Storage Compartment CD/DVD Player — If Equipped WARNING! Do not operate this vehicle with a console compart-...
Page 126: Cupholders
124 GETTING TO KNOW YOUR VEHICLE Cupholders Sunglasses Bin Door At the front of the console a compartment is provided for There are two cupholders for the front seat passengers the storage of a pair of sunglasses. The storage compart- located in the center console.
Page 127: Electrical Power Outlets
GETTING TO KNOW YOUR VEHICLE 125 Power outlets labeled with a “key” are powered when the ignition is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. NOTE: •...
Page 128 126 GETTING TO KNOW YOUR VEHICLE The front power outlet is located inside the storage area on In addition to the front power outlet, there is also a power the center stack of the instrument panel. Push inward on outlet located in the storage area of the center console. the storage lid to open the compartment and gain access to this power outlet.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 The rear power outlet is located in the right rear cargo area. NOTE: The rear power outlet can be switched from switched “ignition” only to constant “battery” powered all the time. See your local authorized dealer for details. Rear Power Outlet Power Outlet Right Rear Quarter Panel Fuse...
Page 130 128 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 131: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 129 Power Inverter — If Equipped The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the There is a 115 Volt, 150 Watt inverter outlet located on the power inverter will automatically shut down.
Page 132: Roof Luggage Rack - If Equipped
130 GETTING TO KNOW YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED NOTE: • To help control wind noise when the crossbars are not in The crossbars and siderails are designed to carry the use, place the front and rear crossbars approximately weight on vehicles equipped with a luggage rack.
Page 133 GETTING TO KNOW YOUR VEHICLE 131 CAUTION! • To prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface.
Page 135 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....134 WARNING/INDICATOR LIGHTS AND MESSAGES ......149 ▫...
Page 136: Instrument Cluster
134 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Base Instrument Cluster...
Page 137: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 135 Instrument Cluster Descriptions CAUTION! 1. Tachometer Driving with a hot engine cooling system could dam- • Indicates the engine speed in revolutions per minute age your vehicle. If the temperature gauge reads “H” (RPM x 1000).
Page 138: Instrument Cluster Display - If Equipped
136 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY — IF EQUIPPED Instrument Cluster Display Location And Controls Your vehicle may be equipped with an instrument cluster The instrument cluster display is located in the center of display, which offers useful information to the driver. With the instrument cluster.
Page 139 GETTING TO KNOW YOUR INSTRUMENT PANEL 137 • Trip • Up Arrow Button • Stop/Start — If Equipped Push and release the up arrow button to scroll upward through the Main Menu items • Audio • Stored Messages • Down Arrow Button •...
Page 140: Oil Change Reset
138 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Change Reset 2. Navigate to Oil Life submenu in Vehicle Info in the instrument cluster display. Your vehicle is equipped with an engine oil change indi- cator system. The “Oil Change Required” message will 3.
Page 141: Instrument Cluster Display Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 139 Instrument Cluster Display Messages • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” Includes the following, but not limited to: • Service Tire Pressure System • Front Seatbelts Unbuckled • Speed Warning Set To XXX MPH •...
Page 142 140 GETTING TO KNOW YOUR INSTRUMENT PANEL • Remote Start Canceled Too Cold • Service Air Suspension System • Remote Start Canceled Door Open • Normal Ride Height Achieved • Remote Start Canceled Hood Open • Aerodynamic Ride Height Achieved •...
Page 143: Instrument Cluster Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 141 Instrument Cluster Display Menu Items Terrain — If Equipped Push and release the up or down arrow button until the NOTE: The instrument cluster display menu items display Terrain icon/title is highlighted in the instrument cluster in the center of the instrument cluster.
Page 144 142 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Menu — If Equipped The ACC screen may display once again if any ACC activity occurs, which may include any of the following: The instrument cluster display displays the current ACC •...
Page 145 GETTING TO KNOW YOUR INSTRUMENT PANEL 143 Fuel Economy Trip Info Push and release the up or down arrow button until the Push and release the up or down arrow button until the Fuel Economy Icon is highlighted in the instrument cluster Trip menu title is displayed in the instrument cluster display.
Page 146 144 GETTING TO KNOW YOUR INSTRUMENT PANEL Audio Screen Setup Driver Selectable Items Push and release the up or down arrow button until the Gear Display Audio menu title is displayed in the instrument cluster • Full (default setting) display. •...
Page 147 GETTING TO KNOW YOUR INSTRUMENT PANEL 145 Upper Right Favorite Menus — Equipped • None • Speedometer • Compass • Vehicle Info • Outside Temp (default setting) • Terrain (show/hide) • Time • Driver Assist (show/hide) • Range • Fuel Economy (show/hide) •...
Page 148: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
146 GETTING TO KNOW YOUR INSTRUMENT PANEL Speed Warning — If Equipped Load reduction is only active when the engine is running. It will display a message if there is a risk of battery Push and release the up or down arrow button until the depletion to the point where the vehicle may stall due to Speed Warning Menu icon/title is highlighted in the lack of electrical supply, or will not restart after the current...
Page 149 GETTING TO KNOW YOUR INSTRUMENT PANEL 147 The electrical loads that may be switched off (if equipped), • Installing options like additional lights, upfitter electri- and vehicle functions which can be effected by load cal accessories, audio systems, alarms and similar de- reduction: vices.
Page 150: Trip Computer
148 GETTING TO KNOW YOUR INSTRUMENT PANEL TRIP COMPUTER What to do when an electrical load reduction action message is present (“Battery Saver On” or “Battery Saver Push and release the up or down arrow button until the Trip Mode”) A or Trip B icon is highlighted in the instrument cluster During a trip: display (Toggle left or right to select Trip A or Trip B).
Page 151: Warning/Indicator Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 149 Elapsed Time exhaustive and/or alternative to the information contained in the Owner Manual, which you are advised to read Shows the total elapsed time of travel since the last reset carefully in all cases. Always refer to the information in this when the ignition switch is in the ACC position.
Page 152: Red Telltale Lights
150 GETTING TO KNOW YOUR INSTRUMENT PANEL Red Telltale Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight sec- onds as a bulb check.
Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake appli- cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 154 152 GETTING TO KNOW YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by WARNING! turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- Driving a vehicle with the red brake light on is proximately two seconds.
Page 155 GETTING TO KNOW YOUR INSTRUMENT PANEL 153 Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected.
Page 156 154 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Temperature Warning Light Red Telltale What It Means Light Oil Temperature Warning Light This telltale indicates vehicle oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Battery Charge Warning Light Red Telltale What It Means...
Page 157 GETTING TO KNOW YOUR INSTRUMENT PANEL 155 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob- lem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.
Page 158 156 GETTING TO KNOW YOUR INSTRUMENT PANEL Door Open Warning Light Red Telltale What It Means Light Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Liftgate Open Warning Light Red Telltale What It Means...
Page 159 GETTING TO KNOW YOUR INSTRUMENT PANEL 157 Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmis- sion into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 160: Yellow Telltale Lights
158 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Telltale Lights Engine Malfunction Warning Light Yellow Telltale What It Means Light Vehicle Check/Malfunction Indicator Light (MIL) The Vehicle Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors emissions control systems. The light will illuminate when the igni- tion is in the ON position before vehicle start up.
Page 161 GETTING TO KNOW YOUR INSTRUMENT PANEL 159 CAUTION! CAUTION! (Continued) driveability. If the MIL is flashing, severe catalytic Prolonged driving with the Malfunction Indicator converter damage and power loss will soon occur. Light (MIL) on could cause damage to the vehicle Immediate service is required.
Page 162 160 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Telltale What It Means Light • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.
Page 163 GETTING TO KNOW YOUR INSTRUMENT PANEL 161 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
Page 164 162 GETTING TO KNOW YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire CAUTION! maintenance, and it is the driver’s responsibility to main- tain correct tire pressure, even if under-inflation has not Do not continue driving with one or more flat tires as reached the level to trigger illumination of the TPMS low handling may be compromised.
Page 165 GETTING TO KNOW YOUR INSTRUMENT PANEL 163 CAUTION! CAUTION! (Continued) Aftermarket wheels can cause sensor damage. Using The TPMS has been optimized for the original equip- aftermarket tire sealants may cause the Tire Pressure ment tires and wheels. TPMS pressures and warning Monitoring System (TPMS) sensor to become inoper- have been established for the tire size equipped on able.
Page 166 164 GETTING TO KNOW YOUR INSTRUMENT PANEL Service Stop/Start System Indicator Light — If Equipped Yellow Telltale What It Means Light Service Stop/Start System Indicator Light This telltale will turn on to indicate the Stop/Start system is not functioning properly and service is required.
Page 167 GETTING TO KNOW YOUR INSTRUMENT PANEL 165 Low Washer Fluid Indicator Light Yellow Telltale What It Means Light Low Washer Fluid Indicator Light This indicator will illuminate when the windshield washer fluid is low. Service Adaptive Cruise Control (ACC) System Indicator Light Yellow Telltale What It Means Light...
Page 168 166 GETTING TO KNOW YOUR INSTRUMENT PANEL 4WD Low Indicator Light — If Equipped Yellow Telltale What It Means Light 4WD Low Indicator Light This light alerts the driver that the vehicle is in the four-wheel drive LOW mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
Page 169 GETTING TO KNOW YOUR INSTRUMENT PANEL 167 LaneSense Failure Indicator Light — If Equipped Yellow Telltale What It Means Light LaneSense Failure Indicator Light This light will turn on when the LaneSense system is not operating and needs service. Please see your authorized dealer.
Page 170: Blue Telltale Lights
168 GETTING TO KNOW YOUR INSTRUMENT PANEL Service 4WD Indicator Light — If Equipped Yellow Telltale What It Means Light Service 4WD Indicator Light If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.
Page 171: Green Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 169 Green Telltale Lights Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light...
Page 172 170 GETTING TO KNOW YOUR INSTRUMENT PANEL Turn Signal Warning Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction le- ver is moved down (left) or up (right).
Page 173 GETTING TO KNOW YOUR INSTRUMENT PANEL 171 Adaptive Cruise Control (ACC) Set With No Target Detected Light — If Equipped Green Telltale What It Means Light Adaptive Cruise Control (ACC) Set With No Target Detected Light — If Equipped This light will turn on when the Adaptive Cruise Control is SET and there is no target vehicle detected.
Page 174 172 GETTING TO KNOW YOUR INSTRUMENT PANEL Sport Mode Indicator Light Green Telltale What It Means Light Sport Mode Indicator Light This light will turn on when Sport Mode is active. Stop/Start Active Indicator Light — If Equipped Green Telltale What It Means Light Stop/Start Active Indicator Light...
Page 175: White Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 173 LaneSense Indicator Light — If Equipped Green Telltale What It Means Light LaneSense Indicator Light The LaneSense indicator is solid green when both lane markings have been detected and the sys- tem is “armed” to provide visual warnings in the instrument cluster display and a torque warn- ing in the steering wheel if an unintentional lane departure occurs.
Page 176 174 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Ready Light — If Equipped White Telltale What It Means Light Adaptive Cruise Control (ACC) Ready Light — If Equipped This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on and in the READY state.
Page 177 GETTING TO KNOW YOUR INSTRUMENT PANEL 175 LaneSense Indicator Light — If Equipped White Telltale What It Means Light LaneSense Indicator Light When the LaneSense system is ON, the LaneSense indicator is solid white when none or only the left or right lane marking has been detected. The indicator will turn green when both lanes are detected and the system will be ready to provide visual warnings in the instrument cluster dis- play if an unintentional lane departure occurs.
Page 178: Onboard Diagnostic System - Obd Ii
176 GETTING TO KNOW YOUR INSTRUMENT PANEL ONBOARD DIAGNOSTIC SYSTEM — OBD II Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is equipped with a sophisticated Onboard Diag- Your vehicle is required to have an Onboard Diagnostic nostic system called OBD II. This system monitors the perfor- system (OBD II) and a connection port to allow access to mance of the emissions, engine, and transmission control sys- information related to the performance of your emissions...
Page 179: Emissions Inspection And Maintenance Programs
GETTING TO KNOW YOUR INSTRUMENT PANEL 177 EMISSIONS INSPECTION AND MAINTENANCE 2. As soon as you cycle the ignition switch to the ON PROGRAMS position, you will see the “Malfunction Indicator Light (MIL)” symbol come on as part of a normal bulb check. In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
Page 180 178 GETTING TO KNOW YOUR INSTRUMENT PANEL Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running.
Page 181 SAFETY CONTENTS SAFETY FEATURES ..... .180 ▫ Seat Belt Systems ..... .215 ▫...
Page 182: Safety Features
180 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 183: Electronic Brake Control System
SAFETY Electronic Brake Control System WARNING! (Continued) Your vehicle is equipped with an advanced Electronic • The capabilities of an ABS equipped vehicle must never Brake Control system (EBC). This system includes Elec- be exploited in a reckless or dangerous manner that tronic Brake Force Distribution (EBD), Anti-Lock Brake could jeopardize the user’s safety or the safety of others.
Page 184 182 SAFETY Brake System Warning Light WARNING! The red “Brake System Warning Light” will turn on when The Brake Assist System (BAS) cannot prevent the the ignition is turned to the ON/RUN mode and may stay natural laws of physics from acting on the vehicle, nor on for as long as four seconds.
Page 185 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s • The vehicle must be stopped. responsibility to be attentive to distance to other ve- hicles, people, and objects, and most importantly brake •...
Page 186 184 SAFETY For vehicles not equipped with an instrument cluster Towing With HSA display, perform the following steps: HSA will also provide assistance to mitigate roll back while towing a trailer. 1. Center the steering wheel (front wheels pointing straight forward). WARNING! 2.
Page 187 SAFETY Traction Control System (TCS) ESC uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual This system monitors the amount of wheel spin of each of path of the vehicle. When the actual path does not match the driven wheels.
Page 188 186 SAFETY WARNING! WARNING! (Continued) vehicle modification or poor vehicle maintenance • Electronic Stability Control (ESC) cannot prevent the that reduces the effectiveness of the ESC system can natural laws of physics from acting on the vehicle, increase the risk of loss of vehicle control, vehicle nor can it increase the traction afforded by prevailing rollover, personal injury and death.
Page 189 SAFETY To enter the “Partial Off” mode, momentarily push the Full Off — If Equipped “ESC Off” switch and the “ESC Off Indicator Light” will This mode is intended for off-highway or off-road use only illuminate. To turn the ESC on again, momentarily push and should not be used on any public roadways.
Page 190 188 SAFETY ESC Activation/Malfunction Indicator Light And WARNING! ESC OFF Indicator Light • In the ESC “Full Off” mode, the engine torque reduction and stability features are disabled. There- The “ESC Activation/Malfunction Indicator fore, enhanced vehicle stability offered by the ESC Light”...
Page 191 SAFETY NOTE: lessen the chance that wheel lift will occur. ERM can only reduce the chance of wheel lift occurring during severe or • The “ESC Activation/Malfunction Indicator Light” and evasive driving maneuvers; it cannot prevent wheel lift the “ESC OFF Indicator Light” come on momentarily due to other factors, such as road conditions, leaving the each time the ignition is turned ON.
Page 192 190 SAFETY Trailer Sway Control (TSC) Ready Alert Braking (RAB) TSC uses sensors in the vehicle to recognize an excessively Ready Alert Braking may reduce the time required to reach swaying trailer and will take the appropriate actions to full braking during emergency braking situations. It antici- attempt to stop the sway.
Page 193 SAFETY NOTE: The DST feature is only meant to help the driver Enabling HDC realize the correct course of action through small torques HDC is enabled by pushing the HDC switch, but the on the steering wheel, which means the effectiveness of the following conditions must also be met to enable HDC: DST feature is highly dependent on the driver’s sensitivity •...
Page 194 192 SAFETY • D = 0.6 mph (1 km/h) Deactivating HDC • 1st = 0.6 mph (1 km/h) HDC will be deactivated but remain available if any of the following conditions occur: • 2nd = 1.2 mph (2 km/h) • Driver overrides HDC set speed with throttle or brake •...
Page 195 SAFETY • The vehicle is driven greater than 40 mph (64 km/h) WARNING! (HDC exits immediately). HDC is only intended to assist the driver in controlling • HDC detects excessive brake temperature. vehicle speed when descending hills. The driver must Feedback To The Driver remain attentive to the driving conditions and is re- sponsible for maintaining a safe vehicle speed.
Page 196 194 SAFETY Enabling SSC The set speed for SSC is selectable by the driver, and can be adjusted by using the gear shift +/-. Additionally, the SSC SSC is enabled by pushing the SSC switch, but the follow- set speed may be reduced when climbing a grade and the ing conditions must also be met to enable SSC: level of set speed reduction depends on the magnitude of •...
Page 197 SAFETY NOTE: Disabling SSC • During SSC the +/- shifter input is used for SSC target SSC will deactivate and be disabled if any of the following speed selection but will not affect the gear chosen by the conditions occur: transmission.
Page 198: Auxiliary Driving Systems
196 SAFETY • The cluster icon and switch lamp will flash for several seconds then extinguish when SSC disables due to excess speed. • The cluster icon and switch lamp will flash then extin- guish when SSC deactivates due to overheated brakes. WARNING! SSC is only intended to assist the driver in controlling vehicle speed when driving in off road conditions.
Page 199 SAFETY both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detec- tion zones.
Page 200 198 SAFETY Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. Warning Light Location The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.
Page 201 SAFETY Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly with a relative speed less side and enter the rear detection zone with a relative speed than 15 mph (24 km/h) and the vehicle remains in the of less than 30 mph (48 km/h).
Page 202 200 SAFETY Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in adjacent berms, etc.
Page 203 SAFETY Rear Cross Path (RCP) The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed.
Page 204 202 SAFETY RCP monitors the rear detection zones on both sides of the Modes Of Operation vehicle, for objects that are moving toward the side of the Three selectable modes of operation are available in the vehicle with a minimum speed of approximately 3 mph Uconnect System.
Page 205 SAFETY NOTE: Whenever an audible alert is requested by the BSM General Information system, the radio is also muted. This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications When the system is in RCP, the system shall respond with Commission (FCC) rules and with Industry Canada Stan- both visual and audible alerts when a detected object is dards RSS- GEN/210/220/310.
Page 206: Forward Collision Warning (Fcw) With Mitigation
204 SAFETY Forward Collision Warning (FCW) With Mitigation If a Forward Collision Warning with Mitigation event begins at a speed below 26 mph (42 km/h), the system may The Forward Collision Warning (FCW) With Mitigation provide the maximum or partial braking to mitigate the system provides the driver with audible warnings, visual potential forward collision.
Page 207 SAFETY NOTE: WARNING! • The minimum speed for FCW activation is 1 mph Forward Collision Warning (FCW) is not intended to (2 km/h). avoid a collision on its own, nor can FCW detect every • The FCW alerts may be triggered on objects other than type of potential collision.
Page 208 206 SAFETY NOTE: The FCW system state is kept in memory from one Changing the FCW status to the “Near” setting, allows the ignition cycle to the next. If the system is turned off, it will system to warn the driver of a possible collision with the remain off when the vehicle is restarted.
Page 209: Tire Pressure Monitor System (Tpms)
SAFETY FCW Limited Warning The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the If the instrument cluster displays “ACC/FCW Limited outside temperature decreases, the tire pressure will de- Functionality”...
Page 210 208 SAFETY NOTE: When filling warm tires, the tire pressure may need CAUTION! to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order to turn the • The TPMS has been optimized for the original Tire Pressure Monitoring Telltale Light off.
Page 211 SAFETY NOTE: Premium System • The TPMS is not intended to replace normal tire care and The Tire Pressure Monitor System (TPMS) uses wireless maintenance, or to provide warning of a tire failure or technology with wheel rim-mounted electronic sensors to condition.
Page 212 210 SAFETY The Tire Pressure Monitor System (TPMS) consists of the following components: • Receiver Module • Four Tire Pressure Monitoring Sensors • Various Tire Pressure Monitoring System Messages, which display in the instrument cluster, and a graphic displaying tire pressures •...
Page 213 SAFETY The system will automatically update, the graphic display will not be present, and a pressure value will be displayed of the pressure value(s) will return to its original color and instead of dashes. A system fault can occur by any of the the Tire Pressure Monitoring Telltale Light will extinguish following: once the updated tire pressure(s) have been received.
Page 214 212 SAFETY sound, and the instrument cluster display will still display a TPMS Deactivation — If Equipped pressure value in the different color graphic display and an The TPMS can be deactivated if replacing all four wheel “Inflate to XX” message will be displayed. After driving the and tire assemblies (road tires) with wheel and tire assem- vehicle for up to 20 minutes above 15 mph (24 km/h), the Tire blies that do not have TPMS Sensors, such as when...
Page 215: Occupant Restraint Systems
SAFETY OCCUPANT RESTRAINT SYSTEMS The instrument cluster will display the “SERVICE TPM SYSTEM” message and then display pressure values in Some of the most important safety features in your vehicle place of the dashes. On the next ignition cycle the SER- are the restraint systems: VICE TPM SYSTEM message will no longer be displayed Occupant Restraint Systems Features...
Page 216 214 SAFETY Here are some simple steps you can take to minimize the 6. All occupants should always wear their lap and shoul- risk of harm from a deploying air bag: der belts properly. 1. Children 12 years old and under should always ride 7.
Page 217: Seat Belt Systems
SAFETY Seat Belt Systems Initial Indication Buckle up even though you are an excellent driver, even on If the driver is unbuckled when the ignition switch is first short trips. Someone on the road may be a poor driver and in the START or ON/RUN position, a chime will signal for could cause a collision that includes you.
Page 218 216 SAFETY has completed, the Seat Belt Reminder Light will remain on NOTE: If BeltAlert has been deactivated and the driver or until the seat belts are buckled. The BeltAlert warning outboard front seat passenger (if equipped with outboard sequence may repeat based on vehicle speed until the front passenger seat BeltAlert) is unbuckled the Seat Belt driver and occupied outboard front seat passenger seat Reminder Light will turn on and remain on until the driver...
Page 219 SAFETY WARNING! (Continued) WARNING! (Continued) • In a collision, you and your passengers can suffer • Two people should never be belted into a single seat much greater injuries if you are not properly buckled belt. People belted together can crash into one an- up.
Page 220 218 SAFETY Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and adjust • A seat belt that is too loose will not protect you the seat. properly. In a sudden stop, you could move too far forward, increasing the possibility of injury.
Page 221 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen. To remove slack in the with minimal, if any slack so that it is comfortable and lap belt portion, pull up on the shoulder belt.
Page 222 220 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 223 SAFETY NOTE: The adjustable upper shoulder belt anchorage is Seat Belt Extender equipped with an Easy Up feature. This feature allows the If a seat belt is not long enough to fit properly, even when shoulder belt anchorage to be adjusted in the upward the webbing is fully extended and the adjustable upper position without pushing or squeezing the release button.
Page 224 222 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 225 SAFETY Switchable Automatic Locking Retractor (ALR) ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in The seat belts in the passenger seating positions are this case and then carefully pull out only the amount of equipped with a Switchable Automatic Locking Retractor webbing necessary to comfortably wrap around the occu- (ALR) which is used to secure a child restraint system.
Page 226 224 SAFETY How To Engage The Automatic Locking Mode WARNING! (Continued) 1. Buckle the combination lap and shoulder belt. properly when checked according to the procedures in the Service Manual. 2. Grasp the shoulder portion and pull downward until • Failure to replace the seat belt assembly could in- the entire seat belt is extracted.
Page 227 SAFETY How The Active Head Restraints (AHR) Work Active Head Restraint (AHR) Components: The Occupant Restraint Controller (ORC) determines whether the severity or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed.
Page 228 226 SAFETY Resetting Active Head Restraints (AHR) WARNING! (Continued) If the Active Head Restraints are triggered during a collision, restraints are placed in their proper positions in the front half of the head restraint will be extended forward order to minimize the risk of neck injury in the event and separated from the rear half of the head restraint (see of a collision.
Page 229: Supplemental Restraint Systems (Srs)
SAFETY • Instrument Panel WARNING! • Knee Impact Bolsters Deployed AHRs are not able to best protect you in all • Driver and Front Passenger Air Bags types of collisions. Have deployed AHRs reset by an authorized dealer immediately. • Supplemental Side Air Bags •...
Page 230 228 SAFETY The ORC turns on the Air Bag Warning Light in the NOTE: If the speedometer, tachometer, or any engine instrument panel for approximately four to eight seconds related gauges are not working, the Occupant Restraint for a self-check when the ignition switch is first in the Controller (ORC) may also be disabled.
Page 231 SAFETY panel. The Redundant Air Bag Warning Light will stay on until the fault is cleared. In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Light has come on and a fault has been detected. If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately.
Page 232 230 SAFETY This vehicle may be equipped with a driver and/or front WARNING! (Continued) passenger seat belt buckle switch that detects whether the to inflate. Sit back, comfortably extending your arms driver or front passenger seat belt is buckled. The seat belt to reach the steering wheel or instrument panel.
Page 233 SAFETY Front Air Bag Operation The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Front Air Bags are designed to provide additional protec- the air bags inflate to their full size. The front air bags fully tion by supplementing the seat belts.
Page 234 232 SAFETY Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and front air bags.
Page 235 SAFETY SABICs may help reduce the risk of head or other injuries WARNING! to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the Do not use accessory seat covers or place objects injury reduction potential provided by the seat belts and between you and the Side Air Bags;...
Page 236 234 SAFETY WARNING! (Continued) WARNING! • In order for the SABICs to work as intended, do not • Occupants, including children, who are up against or install any accessory items in your vehicle which very close to Side Air Bags can be seriously injured could alter the roof.
Page 237 SAFETY The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side • Being too close to the Side Air Bags during deploy- collisions that do not impact the area of the passenger ment could cause you to be severely injured or compartment.
Page 238 236 SAFETY The SABICs may help reduce the risk of partial or complete If A Deployment Occurs ejection of vehicle occupants through side windows in The front air bags are designed to deflate immediately after certain rollover or side impact events. deployment.
Page 239 SAFETY eyes, nose, or throat. If you have skin or eye irritation, Enhanced Accident Response System rinse the area with cool water. For nose or throat In the event of an impact, if the communication network irritation, move to fresh air. If the irritation continues, remains intact, and the power remains intact, depending see your doctor.
Page 240 238 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 241: Child Restraints
SAFETY These data can help provide a better understanding of the Children 12 years or younger should ride properly buckled circumstances in which crashes and injuries occur. up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear NOTE: EDR data are recorded by your vehicle only if a seats rather than in the front.
Page 242 240 SAFETY • Canadian residents should refer to Transport Canada’s NOTE: website additional information: http:// • For additional information, refer to www.safercar.gov/ www.tc.gc.ca/eng/motorvehiclesafety/safedrivers- parents/index.htm or call: 1–888–327–4236 childsafety-index-53.htm Summary Of Recommendations For Restraining Children In Vehicles Recommended Type of Child Re- Child Size, Height, Weight or Age straint Infants and Toddlers...
Page 243 SAFETY Infant And Child Restraints Older Children And Child Restraints Safety experts recommend that children ride rear-facing in Children who are two years old or who have outgrown the vehicle until they are two years old or until they reach their rear-facing convertible child seat can ride forward- either the height or weight limit of their rear-facing child facing in the vehicle.
Page 244 242 SAFETY should use the seat belt in a rear seat. Use this simple 5-step WARNING! test to decide whether the child can use the vehicle’s seat belt alone: • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. 1.
Page 245 SAFETY WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly.
Page 246 244 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 247 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 248 246 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact.
Page 249 SAFETY Locating The Upper Tether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat. To access them, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages.
Page 250 248 SAFETY Center Seat LATCH WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not ap- proved for installing child seats using the LATCH attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position.
Page 251 SAFETY 3. Raise the armrest and attach the tether hook to the strap 2. Place the child seat between the lower anchorages for located on the front of the arm rest. that seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit.
Page 252 250 SAFETY How To Stow An Unused Switchable-ALR (ALR) WARNING! (Continued) Seat Belt: • Child restraint anchorages are designed to withstand When using the LATCH attaching system to install a child only those loads imposed by correctly-fitted child restraint, stow all ALR seat belts that are not being used by restraints.
Page 253 SAFETY The seat belts in the passenger seating positions are Lap/Shoulder Belt Systems For Installing Child equipped with a Switchable Automatic Locking Retractor Restraints In This Vehicle (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 254 252 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + Weight limit of the Always use the tether anchor when using the weight of the child restraint) for using the Child Restraint seat belt to install a forward facing child re- Tether Anchor with the seat belt to attach a...
Page 255 SAFETY Installing A Child Restraint With A Switchable 3. Slide the latch plate into the buckle until you hear a Automatic Locking Retractor (ALR): “click.” Child restraint systems are designed to be secured in 4. Pull on the webbing to make the lap portion tight vehicle seats by lap belts or the lap belt portion of a against the child seat.
Page 256 254 SAFETY 9. Test that the child restraint is installed tightly by pulling 1. Look behind the seating position where you plan to back and forth on the child seat at the belt path. It should install the child restraint to find the tether anchorage. not move more than 1 inch (25.4 mm) in any direction.
Page 257 SAFETY 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. Top Tether Strap Anchorage (Located On Seatback) 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.
Page 258: Transporting Pets
256 SAFETY SAFETY TIPS WARNING! (Continued) Transporting Passengers • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the NEVER TRANSPORT PASSENGERS IN THE CARGO child. Use only the anchorage position directly be- AREA. hind the child seat to secure a child restraint top tether strap.
Page 259: Exhaust Gas
SAFETY Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the WARNING! vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete Exhaust gases can injure or kill.
Page 260 258 SAFETY Air Bag Warning Light of position and interfere with the pedal assemblies or impair safe operation of your vehicle in other ways. The Air Bag warning light will turn on for four to eight seconds as a bulb check when the ignition switch WARNING! is first turned to ON/RUN.
Page 261: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY WARNING! (Continued) WARNING! (Continued) • ONLY use the driver’s side floor mat on the driver’s • If the vehicle carpet has been removed and re- side floor area. To check for interference, with the installed, always properly attach carpet to the floor vehicle properly parked with the engine off, fully and check the floor mat fasteners are secure to the depress the accelerator, the brake, and the clutch...
Page 262 260 SAFETY Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks.
Page 263 STARTING AND OPERATING CONTENTS STARTING THE ENGINE — GAS ... .265 ENGINE BLOCK HEATER — IF EQUIPPED ..271 ▫ Automatic Transmission ....265 ENGINE BREAK-IN RECOMMENDATIONS —...
Page 264 262 STARTING AND OPERATING ▫ Shift Positions ......286 ▫ To Vary The Speed Setting ....301 ▫...
Page 265 STARTING AND OPERATING 263 ▫ Adaptive Cruise Control (ACC) Menu ..314 ▫ ParkSense Display ..... .335 ▫...
Page 266 264 STARTING AND OPERATING ▫ Towing Requirements ....382 PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED ......369 ▫...
Page 267: Starting The Engine - Gas
STARTING AND OPERATING 265 STARTING THE ENGINE — GAS WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the ignition of a vehicle equipped with Keyless Enter- inside and outside mirrors, fasten your seat belt, and if N-Go in the ACC or ON/RUN mode. A child could present, instruct all other occupants to buckle their seat operate power windows, other controls, or move the belts.
Page 268: Normal Starting
266 STARTING AND OPERATING To Turn Off The Engine Using ENGINE START/STOP CAUTION! (Continued) Button • Shift into or out of REVERSE only after the vehicle 1. Place the gear selector in PARK, then push and release has come to a complete stop and the engine is at idle the ENGINE START/STOP button.
Page 269: If Engine Fails To Start
STARTING AND OPERATING 267 If Engine Fails To Start NOTE: The system will automatically time out and the ignition will cycle to the OFF mode after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine WARNING! not running) mode and the transmission is in PARK.
Page 270: Cold Weather Operation (Below -22°F Or −30°C)
268 STARTING AND OPERATING Cold Weather Operation (Below –22°F Or −30°C) To Activate The Autostop Mode, The Following Must Occur: To ensure reliable starting at these temperatures, use of an • The system must be in STOP/START READY state. A externally powered electric engine block heater (available STOP/START READY message will be displayed in the from your authorized dealer) is recommended.
Page 271: Possible Reasons The Engine Does Not Autostop
STARTING AND OPERATING 269 Possible Reasons The Engine Does Not Autostop • The transmission is not in a forward gear. Prior to engine shut down, the system will check many • Hood is open. safety and comfort conditions to see if they are fulfilled. •...
Page 272: To Start The Engine While In Autostop Mode
270 STARTING AND OPERATING To Start The Engine While In Autostop Mode To Manually Turn Off The Stop/Start System While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is depressed. The transmission will automatically re-engage upon en- gine restart.
Page 273: To Manually Turn On The Stop/Start System
STARTING AND OPERATING 271 4. The STOP/START system will reset itself back to an ON The engine block heater must be plugged in at least one condition every time the ignition is turned off and back hour to have an adequate warming effect on the engine. The engine block heater cord is located: To Manually Turn On The Stop/Start System •...
Page 274: Parking Brake
272 STARTING AND OPERATING PARKING BRAKE While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Before leaving the vehicle, make sure that the parking However, wide-open throttle acceleration in low gear can brake is fully applied and place the gear selector in the be detrimental and should be avoided.
Page 275 STARTING AND OPERATING 273 When the parking brake is applied with the ignition switch WARNING! in the ON mode, the Brake Warning Light in the instru- ment cluster will illuminate. • Never use the PARK position as a substitute for the parking brake.
Page 276: Automatic Transmission
274 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! (Continued) • Be sure the parking brake is fully disengaged before WARNING! driving; failure to do so can lead to brake failure and • Never use the PARK position as a substitute for the a collision.
Page 277 STARTING AND OPERATING 275 WARNING! (Continued) WARNING! (Continued) vehicle could accelerate quickly forward or in re- touch the parking brake, brake pedal or the trans- verse. You could lose control of the vehicle and hit mission gear selector. • Do not leave the key fob in or near the vehicle (or in someone or something.
Page 278: Ignition Park Interlock
276 STARTING AND OPERATING Ignition Park Interlock This vehicle is equipped with an Ignition Park Interlock which requires the transmission to be in PARK before the ignition can be turned to the OFF mode. This helps the driver avoid inadvertently leaving the vehicle without placing the transmission in PARK.
Page 279: Eight-Speed Automatic Transmission
STARTING AND OPERATING 277 Active Noise Cancellation — If Equipped The electronically-controlled transmission adapts its shift schedule based on driver inputs, along with environmental Your vehicle is equipped with an Active Noise Cancellation and road conditions. The transmission electronics are self- System.
Page 280 278 STARTING AND OPERATING Gear Ranges Do not depress the accelerator pedal when shifting from PARK or NEUTRAL into another gear range. NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
Page 281 STARTING AND OPERATING 279 When exiting the vehicle, always: WARNING! (Continued) • Apply the parking brake, that the transmission gear position indicator solidly • Shift the transmission into PARK, indicates PARK (P) without blinking. Ensure that the vehicle is completely stopped, and the PARK posi- •...
Page 282 280 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • When exiting the vehicle, always make sure the • DO NOT race the engine when shifting from PARK ignition is in the OFF mode, remove the key fob from or NEUTRAL into another gear range, as this can the vehicle, and lock the vehicle.
Page 283 STARTING AND OPERATING 281 REVERSE (R) CAUTION! (Continued) This range is for moving the vehicle backward. Shift into Refer to “Recreational Towing” in “Starting And Op- REVERSE only after the vehicle has come to a complete erating” and “Towing A Disabled Vehicle” in “In Case stop.
Page 284 282 STARTING AND OPERATING speed. Normal operation will resume once the transmis- In the event of a momentary problem, the transmission can sion temperature has risen to a suitable level. be reset to regain all forward gears by performing the following steps: MANUAL (M) NOTE: In cases where the instrument cluster message...
Page 285 STARTING AND OPERATING 283 If the transmission cannot be reset, authorized dealer shift the transmission. Tapping the gear selector forward (-) service is required. while in the MANUAL (M) position, or tapping the (-) shift paddle (if equipped) on the steering wheel, will downshift AutoStick the transmission to the next lower gear.
Page 286: Sport Mode - If Equipped
284 STARTING AND OPERATING • You can start out, from a stop, in first or second gear (or To disengage AutoStick, return the gear selector to the third gear, in 4LO range, Snow mode, or Sand mode). DRIVE position, or press and hold the (+) shift paddle (if Tapping (+) (at a stop) will allow starting in second gear.
Page 287: Four Wheel Drive Operation
STARTING AND OPERATING 285 FOUR WHEEL DRIVE OPERATION This transfer case is fully automatic in the 4WD HI mode. When additional traction is required, the 4WD LOW Quadra-Trac I Operating Instructions/ position can be used to lock the front and rear driveshafts Precautions —...
Page 288: Shift Positions
286 STARTING AND OPERATING NEUTRAL WARNING! This range disengages the driveline from the powertrain. It You or others could be injured or killed if you leave the is to be used for flat towing behind another vehicle. Refer vehicle unattended with the transfer case in the NEU- to “Recreational Towing”...
Page 289: Shifting Procedures
STARTING AND OPERATING 287 4WD LOW This range is for low speed four-wheel drive. It provides an additional gear reduction which allows for increased torque to be delivered to both the front and rear wheels while providing maximum pulling power for loose, slip- pery road surfaces only.
Page 290 288 STARTING AND OPERATING NOTE: Shifting Into NEUTRAL (N) • If shift conditions/interlocks are not met, or a transfer WARNING! case motor temperature protection condition exists, a “For 4x4 High Slow Below 3 mph (5 km/h) Put Trans in You or others could be injured or killed if you leave the N push 4 Low”...
Page 291 STARTING AND OPERATING 289 5. Using a ballpoint pen or similar object, push and hold 7. Shift the transmission into REVERSE. the recessed transfer case NEUTRAL (N) button (located 8. Release the brake pedal for five seconds and ensure that by the selector switch) for four seconds.
Page 292: Quadra-Drive Ii System - If Equipped
290 STARTING AND OPERATING Quadra-Drive II System — If Equipped The optional Quadra-Drive II System features two torque transfer couplings. The couplings include an Electronic Limited-Slip Differential (ELSD) rear axle and the Quadra- Trac II transfer case. The optional ELSD axle is fully automatic and requires no driver input to operate.
Page 293: Quadra-Lift - If Equipped
STARTING AND OPERATING 291 QUADRA-LIFT — IF EQUIPPED Description The Quadra-Lift air suspension system provides full time load leveling capability along with the benefit of vehicle height adjustment by the push of a button. The vehicle will automatically raise and lower the ride height to adapt to the appropriate driving conditions.
Page 294 292 STARTING AND OPERATING • Off-Road 1 (OR1) (Raises the vehicle approximately automatically enter Aero Mode when the vehicle speed 1.1 inches (28 mm) – This is the primary position for all remains between 52 mph (83 km/h) and 56 mph off-road driving until OR2 is needed.
Page 295 STARTING AND OPERATING 293 NOTE: Automatic lowering of the vehicle into Entry/Exit The Quadra-Lift air suspension system uses a lifting and Mode can be enabled through the Uconnect Touch-Screen lowering pattern which keeps the headlights from incor- Radio. If this feature is enabled, the vehicle will only lower rectly shining into oncoming traffic.
Page 296: Air Suspension Modes
294 STARTING AND OPERATING NOTE: This mode is intended to be enabled with engine WARNING! running. The air suspension system uses a high pressure vol- Transport Mode ume of air to operate the system. To avoid personal To assist with flat bed towing, the air suspension system injury or damage to the system, see your authorized has a feature which will put the vehicle into Entry/Exit dealer for service.
Page 297: Instrument Cluster Display Messages
STARTING AND OPERATING 295 Wheel Alignment Mode flashing on the “Up” button, the highest flashing indicator lamp is the position the system is working to achieve. Before performing a wheel alignment this mode must be When lowering, if multiple indicators are flashing on the enabled.
Page 298 296 STARTING AND OPERATING Automatic height changes will occur based on vehicle lamp 3 will flash until Entry/Exit Mode is achieved at speed and the current vehicle height. The indicator lamps which point indicator lamp 3 will go solid. If during the and instrument cluster display messages will operate the height change to Entry/Exit Mode, the vehicle speed same for automatic changes and user requested changes.
Page 299: Selec-Terrain - If Equipped
STARTING AND OPERATING 297 SELEC-TERRAIN — IF EQUIPPED minimize wheel slippage. If equipped with air suspen- sion, the default ride height for Snow is Normal Ride Selec-Terrain Mode Selection Height (NRH). Selec-Terrain combines the capabilities of the vehicle con- • Auto – Fully automatic full time four-wheel drive op- trol systems, along with driver input, to provide the best eration can be used on and off road.
Page 300: Instrument Cluster Display Messages
298 STARTING AND OPERATING • Rock – Off road calibration only available in 4WD Low FUEL SAVER TECHNOLOGY 5.7L ENGINE ONLY — IF EQUIPPED range. The vehicle is raised (if equipped with Air Suspension) for improved ground clearance. Traction This feature offers improved fuel economy by shutting off based tuning with improved steer-ability for use on high four of the engine’s eight cylinders during light load and traction off-road surfaces.
Page 301: Speed Control - If Equipped
STARTING AND OPERATING 299 SPEED CONTROL — IF EQUIPPED Alternate electric power steering efforts can be selected through the Uconnect System. Refer to ”Customer Pro- When engaged, the Speed Control takes over accelerator grammable Features” within “Uconnect Settings” in “Mul- operations at speeds greater than 25 mph (40 km/h).
Page 302: To Activate
300 STARTING AND OPERATING NOTE: In order to ensure proper operation, the Speed WARNING! Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If Leaving the Speed Control system on when not in use this occurs, the Speed Control System can be reactivated by is dangerous.
Page 303: To Vary The Speed Setting
STARTING AND OPERATING 301 To Vary The Speed Setting • If the button is continually pushed, the set speed will continue to increase until the button is released, then the To Increase Speed new set speed will be established. When the Speed Control is set, you can increase speed by To Decrease Speed pushing the SET (+) button.
Page 304: To Accelerate For Passing
302 STARTING AND OPERATING Using Speed Control On Hills Metric Speed (km/h) • Pushing the SET (-) button once will result in a 1 km/h The transmission may downshift on hills to maintain the decrease in set speed. Each subsequent tap of the button vehicle set speed.
Page 305: Adaptive Cruise Control (Acc) - If Equipped
STARTING AND OPERATING 303 ADAPTIVE CRUISE CONTROL (ACC) — IF The Cruise Control system has two control modes: EQUIPPED • Adaptive Cruise Control mode for maintaining an ap- propriate distance between vehicles. Adaptive Cruise Control (ACC) increases the driving con- venience provided by cruise control while traveling on •...
Page 306 304 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Will bring the vehicle to a complete stop while operation of the vehicle under all road conditions. following a target vehicle and hold the vehicle for Your complete attention is always required while driving to maintain safe control of your vehicle.
Page 307: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING 305 Adaptive Cruise Control (ACC) Operation NOTE: Any chassis/suspension or tire size modifications to the vehicle will effect the performance of the Adaptive The Speed Control buttons (located on the right side of the Cruise Control and Forward Collision Warning System. steering wheel) operates the ACC system.
Page 308: To Activate/Deactivate
306 STARTING AND OPERATING • When the brakes are overheated. To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button again. At this time, the • When the driver’s door is open at low speeds. system will turn off and the instrument cluster displays •...
Page 309: To Set A Desired Acc Speed
STARTING AND OPERATING 307 To Set A Desired ACC Speed To Cancel When the vehicle reaches the speed desired, push the SET The following conditions cancel the system: (+) button or the SET (-) button and release. The instrument • The brake pedal is applied. cluster display will display the set speed.
Page 310: To Turn Off
308 STARTING AND OPERATING To Turn Off WARNING! The system will turn off and clear the set speed in memory if: The Resume function should only be used if traffic • The Adaptive Cruise Control (ACC) on/off button is and road conditions permit. Resuming a set speed that pushed.
Page 311 STARTING AND OPERATING 309 • If the button is continually pushed, the set speed will The speed decrement shown is dependant on the chosen continue to increase in 5 mph increments until the speed unit of U.S. (mph) or Metric (km/h): button is released.
Page 312: Setting The Following Distance In Acc
310 STARTING AND OPERATING Setting The Following Distance In ACC NOTE: • When you override and push the SET (+) button or The specified following distance for ACC can be set by SET (-) buttons, the new Set Speed will be the current varying the distance setting between four bars (longest), speed of the vehicle.
Page 313 STARTING AND OPERATING 311 Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 314 312 STARTING AND OPERATING The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed. • The vehicle ahead moves out of your lane or view of the sensor. • The distance setting is changed. •...
Page 315: Overtake Aid
STARTING AND OPERATING 313 ACC Operation At Stop If the ACC system brings your vehicle to a standstill while following a target vehicle, if the target vehicle starts moving within two seconds of your vehicle coming to a standstill, your vehicle will resume motion without the need for any driver action.
Page 316: Adaptive Cruise Control (Acc) Menu
314 STARTING AND OPERATING Adaptive Cruise Control Set WARNING! When the SET (+) or the SET (-) button (located on the When the ACC system is resumed, the driver must steering wheel) is pushed, the display will read “ACC ensure that there are no pedestrians, vehicles or objects SET.”...
Page 317: Display Warnings And Maintenance
STARTING AND OPERATING 315 Display Warnings And Maintenance If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of “Wipe Front Radar Sensor In Front Of Vehicle” an obstruction. The sensor is located in the center of the Warning vehicle behind the lower grille.
Page 318 316 STARTING AND OPERATING NOTE: The “ACC/FCW Limited Functionality Clean Front Wind- shield” message can sometimes be displayed while driving • If the “ACC/FCW Unavailable Wipe Front Radar Sen- in adverse weather conditions. The ACC/FCW system will sor” message occurs frequently (e.g. more than once on recover after the vehicle has left these areas.
Page 319: Precautions While Driving With Acc
STARTING AND OPERATING 317 Service ACC/FCW Warning Offset Driving If the system turns off, and the instrument cluster displays ACC may not detect a vehicle in the same lane that is offset “ACC/FCW Unavailable Service Required” or “Cruise/ from your direct line of travel, or a vehicle merging in from FCW Unavailable Service Required”, there may be an a side lane.
Page 320 318 STARTING AND OPERATING Turns And Bends Using ACC On Hills When driving on a curve with ACC engaged, the system When driving on hills, ACC may not detect a vehicle in may decrease the vehicle speed and acceleration for stabil- your lane.
Page 321 STARTING AND OPERATING 319 Lane Changing Narrow Vehicles ACC may not detect a vehicle until it is completely in the Some narrow vehicles traveling near the outer edges of the lane in which you are traveling. In the illustration shown, lane or edging into the lane are not detected until they have ACC has not yet detected the vehicle changing lanes and it moved fully into the lane.
Page 322: General Information
320 STARTING AND OPERATING Stationary Objects And Vehicles Operation is subject to the following two conditions: ACC does not react to stationary objects and stationary 1. The device may not cause harmful interference. vehicles. For example, ACC will not react in situations 2.
Page 323 STARTING AND OPERATING 321 To Vary The Speed Setting WARNING! To Increase Speed In the Normal (Fixed Speed) Cruise Control mode, the When the Normal (Fixed Speed) Cruise Control is set, you system will not react to vehicles ahead. In addition, the can increase speed by pushing the SET (+) button.
Page 324 322 STARTING AND OPERATING • If the button is continually pushed, the set speed will Metric Speed (km/h) continue to decrease in 5 mph decrements until the • Pushing the SET (+) button once will result in a 1 km/h button is released.
Page 325: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING 323 PARKSENSE REAR PARK ASSIST — IF EQUIPPED • The vehicle parking brake is applied. • The braking temperature exceeds normal range (over- The ParkSense Rear Park Assist system provides visual and heated). audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.g.
Page 326: Parksense Sensors
324 STARTING AND OPERATING • The automatic braking function may not be applied fast ParkSense will retain the last system state (enabled or enough for obstacles that move toward the rear of the disabled) from the last ignition cycle when the ignition is vehicle from the left and/or right sides.
Page 327: Parksense Warning Display
STARTING AND OPERATING 325 ParkSense Warning Display The ParkSense Warning screen will only be displayed if Sound and Display is selected from the Customer - Pro- grammable Features section of the Uconnect System. Refer to Uconnect Settings” in “Multimedia” for further infor- mation.
Page 328 326 STARTING AND OPERATING If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or right rear region and the system will produce a tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous.
Page 329 STARTING AND OPERATING 327 Slow Tone Fast Tone...
Page 330 328 STARTING AND OPERATING Fast Tone Continuous Tone...
Page 331 STARTING AND OPERATING 329 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Rear Dis- Greater...
Page 332: Enabling And Disabling Parksense
330 STARTING AND OPERATING Adjustable Chime Volume Settings The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED Rear chime volume settings can be selected from the will be off when the system is enabled. If the ParkSense Customer-Programmable Features section of the Uconnect switch is pushed, and the system requires service, the System, refer to “Uconnect Settings”...
Page 333: Cleaning The Parksense System
STARTING AND OPERATING 331 is clean and clear of snow, ice, mud, dirt or other obstruc- • When you move the gear selector to the REVERSE tion and then cycle the ignition. If the message continues to position and ParkSense is turned off, the instrument appear, see an authorized dealer.
Page 334 332 STARTING AND OPERATING • ParkSense should be disabled when the liftgate is in the WARNING! (Continued) open position and the vehicle is in REVERSE. An open rear fascia when the loudspeaker sounds the con- liftgate could provide a false indication that an obstacle tinuous tone.
Page 335: Parksense Front And Rear Park Assist - If Equipped
STARTING AND OPERATING 333 PARKSENSE FRONT AND REAR PARK ASSIST — • The automatic braking function will not be available if IF EQUIPPED vehicle is in 4LO transfer case mode. The ParkSense Park Assist system provides visual and • The automatic braking function may not be applied fast audible indications of the distance between the rear and/or enough for obstacles that move toward the rear of the front fascia and a detected obstacle when backing up or...
Page 336: Parksense Sensors
334 STARTING AND OPERATING Refer to “ParkSense System Usage Precautions” for limita- The six ParkSense sensors, located in the front fascia/ tions of this system and recommendations. bumper, monitor the area in front of the vehicle that is within the sensors’ field of view. The sensors can detect ParkSense will retain the last system state (enabled or obstacles from approximately 12 inches (30 cm) up to disabled) from the last ignition cycle when the ignition is...
Page 337: Parksense Display
STARTING AND OPERATING 335 ParkSense Display If an object is detected in the left and/or right rear region, the display will show a single arc in the left and/or right The warning display will turn on indicating the system rear region and the system will produce a tone. As the status when the vehicle is in REVERSE or when the vehicle vehicle moves closer to the object, the display will show the is in DRIVE and an obstacle has been detected.
Page 338 336 STARTING AND OPERATING Slow Tone Slow Tone For Rear Only...
Page 339 STARTING AND OPERATING 337 Fast Tone For Rear Only Fast Tone...
Page 340 338 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone WARNING ALERTS FOR REAR Rear Dis-...
Page 341 STARTING AND OPERATING 339 Arcs-Center None 6th Solid 5th Solid 4th Solid Flashing Flashing Flashing Arcs-Right None None None None None Flashing Flashing Radio Vol- ume Re- duced WARNING ALERTS FOR FRONT Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm)
Page 342: Enabling And Disabling Parksense
340 STARTING AND OPERATING Front Park Assist Audible Alerts for further information. When the gear selector is moved to REVERSE and the system is disabled, the instrument ParkSense will turn off the Front Park Assist audible alert cluster display will display the “PARKSENSE OFF” mes- (chime) after approximately 3 seconds when an obstacle sage for as long as the vehicle is in REVERSE.
Page 343: Cleaning The Parksense System
STARTING AND OPERATING 341 instrument cluster display will display a PARKSENSE UN- If the PARKSENSE UNAVAILABLE SERVICE RE- AVAILABLE WIPE REAR SENSORS , PARKSENSE UN- QUIRED message appears in the instrument cluster dis- AVAILABLE WIPE FRONT SENSORS or PARKSENSE UN- play, see your authorized dealer.
Page 344 342 STARTING AND OPERATING • ParkSense, when on, will reduce the volume of the radio WARNING! when it is sounding a tone. • Drivers must be careful when backing up even when • Clean the ParkSense sensors regularly, taking care not to using ParkSense.
Page 345: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING 343 NOTE: CAUTION! • The driver is always responsible for controlling the • ParkSense is only a parking aid and it is unable to vehicle, responsible for any surrounding objects, and recognize every obstacle, including small obstacles. Park- must intervene as required.
Page 346: Enabling And Disabling The Parksense Active Park Assist System
344 STARTING AND OPERATING Enabling And Disabling The ParkSense Active Park The ParkSense Active Park Assist system will turn off Assist System automatically for any of the following conditions: • The parking maneuver is completed. The ParkSense Active Park Assist system can be enabled and disabled with the ParkSense Active Park Assist switch, •...
Page 347: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 345 Parallel Parking Space Assistance Operation/ The ParkSense Active Park Assist system will only operate and search for a parking space when the following condi- Display tions are present: When the ParkSense Active Park Assist system is enabled •...
Page 348 346 STARTING AND OPERATING • When seeking for a parking space, the driver should When an available parking space has been found, and the drive as parallel or perpendicular (depending on the vehicle is not in position, you will be instructed to move type of maneuver) to other vehicles as possible.
Page 349 STARTING AND OPERATING 347 Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 350 348 STARTING AND OPERATING When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. Check Surroundings — Move Backward NOTE: • It is the driver’s responsibility to use the brake and Check Surroundings —...
Page 351 STARTING AND OPERATING 349 • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 352 350 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 353 STARTING AND OPERATING 351 The system will then instruct the driver to check their surroundings and move forward. Check Surroundings — STOP NOTE: It is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- Check Surroundings —...
Page 354 352 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 355 STARTING AND OPERATING 353 The system will then instruct the driver to check their Your vehicle is now in the parallel park position. When the surroundings and move backward. maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satis- fied with the vehicle position, they should shift to PARK.
Page 356: Perpendicular Parking Space Assistance Operation/Display
354 STARTING AND OPERATING Perpendicular Parking Space Assistance Operation/Display When the ParkSense Active Park Assist system is enabled, the “Active ParkSense Searching - Push OK to Switch to Perpendicular” message will show in the instrument clus- ter display. Push the OK button on the left side steering wheel switch to change your parking space setting to a perpendicular maneuver.
Page 357 STARTING AND OPERATING 355 • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc. from surrounding objects/vehicles).
Page 358 356 STARTING AND OPERATING Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 359 STARTING AND OPERATING 357 When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. Check Surroundings — Move Backward NOTE: • It is the driver’s responsibility to use the brake and accel- Check Surroundings —...
Page 360 358 STARTING AND OPERATING • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 361 STARTING AND OPERATING 359 Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 362 360 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move forward. Check Surroundings — STOP NOTE: It is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- Check Surroundings —...
Page 363 STARTING AND OPERATING 361 Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 364 362 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move backward. Active ParkSense Complete — Check Parking Position WARNING! Check Surroundings — Move Backward • Drivers must be careful when performing parallel or Your vehicle is now in the perpendicular park position.
Page 365 STARTING AND OPERATING 363 WARNING! (Continued) CAUTION! continue to pay attention to your surroundings. Fail- • The ParkSense Active Park Assist system is only a ure to do so can result in serious injury or death. parking aid and it is unable to recognize every •...
Page 366: Lanesense - If Equipped
364 STARTING AND OPERATING LANESENSE — IF EQUIPPED When only a single lane marking is detected and the driver unintentionally drifts across the lane marking (no turn LaneSense Operation signal applied), the LaneSense system provides a visual The LaneSense system is operational at speeds above warning through the instrument cluster display to prompt 37 mph (60 km/h) and below 112 mph (180 km/h).
Page 367 STARTING AND OPERATING 365 The LaneSense button is located on the switch panel below the Uconnect display. LaneSense On Message To turn the LaneSense system off, push the LaneSense button once (LED turns on). LaneSense Warning Button To turn the LaneSense system on, push the LaneSense NOTE: The LaneSense system will retain the last system button (LED turns off).
Page 368: Lanesense Warning Message
366 STARTING AND OPERATING LaneSense Warning Message Left Lane Departure — Only Left Lane Detected • When the LaneSense system is on, the LaneSense telltale The LaneSense system will indicate the current lane drift is solid white when only the left lane marking has been condition through the instrument cluster display.
Page 369 STARTING AND OPERATING 367 NOTE: The LaneSense system operates with the similar • When the LaneSense system senses a lane drift situation, behavior for a right lane departure when only the right the left thick lane line and left thin line turn solid yellow. lane marking has been detected.
Page 370: Changing Lanesense Status
368 STARTING AND OPERATING • When the LaneSense system senses the lane has been Changing LaneSense Status approached and is in a lane departure situation, the left The LaneSense system has settings to adjust the intensity of thick lane line flashes yellow (on/off) and the left thin the torque warning and the warning zone sensitivity line remains solid yellow.
Page 371: Parkview Rear Back Up Camera - If Equipped
STARTING AND OPERATING 369 PARKVIEW REAR BACK UP CAMERA — IF out of REVERSE unless the forward vehicle speed exceeds EQUIPPED 8 mph (13 km/h), the transmission is shifted into PARK or the ignition is switched to the OFF position. Your vehicle may be equipped with the ParkView Rear Back Up Camera that allows you to see an on-screen image NOTE: The ParkView Rear Back Up Camera has program-...
Page 372 370 STARTING AND OPERATING NOTE: If snow, ice, mud, or any foreign substance builds WARNING! up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.
Page 373: Refueling The Vehicle - Gasoline
STARTING AND OPERATING 371 REFUELING THE VEHICLE — GASOLINE ENGINE 1. Push the fuel filler door release switch (located under the headlamp switch). Fuel Filler Door Latch NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door Fuel Filler Door Release Switch using the inside release button.
Page 374 372 STARTING AND OPERATING 6. Wait five seconds before removing the fuel nozzle to WARNING! allow fuel to drain from nozzle. • Never have any smoking materials lit in or near the 7. Remove the fuel nozzle and close the fuel door. vehicle when the fuel door is open or the tank is Emergency Gas Can Refueling being filled.
Page 375: Emergency Fuel Filler Door Release
STARTING AND OPERATING 373 Emergency Fuel Filler Door Release If you are unable to open the fuel filler door, use the fuel filler door emergency release. 1. Open the liftgate. 2. Push the inboard edge of the left storage bin to the center, this will pop up the outboard edge.
Page 376: Vehicle Loading
374 STARTING AND OPERATING VEHICLE LOADING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front Certification Label and rear axles. The load must be distributed in the cargo As required by National Highway Traffic Safety Adminis- area so that the GAWR of each axle is not exceeded.
Page 377: Trailer Towing
STARTING AND OPERATING 375 Curb Weight Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way The curb weight of a vehicle is defined as the total weight the brakes operate. of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded CAUTION!
Page 378: Common Towing Definitions
376 STARTING AND OPERATING Common Towing Definitions WARNING! (Continued) The following trailer towing related definitions will assist ensure stable handling of your vehicle. If you use a you in understanding the following information: standard weight-carrying hitch, you could lose control of your vehicle and cause a collision.
Page 379 STARTING AND OPERATING 377 Tongue Weight (TW) Weight-Carrying Hitch The tongue weight is the downward force exerted on the A weight-carrying hitch supports the trailer tongue weight, hitch ball by the trailer. You must consider this as part of just as if it were luggage located at a hitch ball or some other the load on your vehicle.
Page 380: Trailer Hitch Classification
378 STARTING AND OPERATING Trailer Hitch Classification WARNING! The following chart provides the industry standard for the • An improperly adjusted Weight Distributing Hitch maximum trailer weight a given trailer hitch class can tow system may reduce handling, stability, braking per- and should be used to assist you in selecting the correct formance, and could result in a collision.
Page 381: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 379 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain: Max. GTW (Gross Max. Trailer Tongue Engine Model Frontal Area Trailer Wt.) Wt. (See Note) 3.6L (Std Cooling) 55 sq ft (5.11 sq m) 3,500 lbs (1,587 kg)
Page 382: Trailer Hitch Receiver Cover Removal (Summit Models) - If Equipped
380 STARTING AND OPERATING Trailer Hitch Receiver Cover Removal (Summit Models) — If Equipped Your vehicle may be equipped with a trailer hitch receiver cover, this must be removed to access the trailer hitch receiver (if equipped). This hitch receiver cover is located at the bottom center of the rear fascia.
Page 383: Trailer And Tongue Weight
STARTING AND OPERATING 381 Hitch Receiver Cover Weight Distribution To reinstall the hitch receiver cover after towing repeat the Consider the following items when computing the weight procedure in reverse order. on the rear axle of the vehicle: • The tongue weight of the trailer. NOTE: Be sure to engage all tabs of the hitch receiver cover in the bumper fascia prior to installation.
Page 384: Towing Requirements
382 STARTING AND OPERATING NOTE: Remember that everything put into or on the WARNING! trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must Improper towing can lead to a collision. Follow these be considered as part of the total load on your vehicle. guidelines to make your trailer towing as safe as Refer to the “Tire And Loading Information”...
Page 385 STARTING AND OPERATING 383 Towing Requirements — Tires WARNING! (Continued) • Do not attempt to tow a trailer while using a compact • Vehicles with trailers should not be parked on a spare tire. grade. When parking, apply the parking brake on the tow vehicle.
Page 386 384 STARTING AND OPERATING Towing Requirements — Trailer Brakes CAUTION! • Do not interconnect the hydraulic brake system or If the trailer weighs more than 1,000 lbs (453 kg) vacuum system of your vehicle with that of the trailer. loaded, it should have its own brakes and they should This could cause inadequate braking and possible per- be of adequate capacity.
Page 387 STARTING AND OPERATING 385 NOTE: • Disconnect trailer wiring connector from the vehicle before launching a boat (or any other device plugged into vehicle’s electrical connect) into water. • Be sure to reconnect after clear from water area. Seven-Pin Connector 1 —...
Page 388: Towing Tips
386 STARTING AND OPERATING Towing Tips • To prevent excess heat generation, avoid continuous driving at high RPM. Reduce vehicle speed as necessary Before setting out on a trip, practice turning, stopping, and to avoid extended driving at high RPM. Return to a backing up the trailer in an area located away from heavy higher gear or vehicle speed when grade and road traffic.
Page 389: Snow Plow
STARTING AND OPERATING 387 Air Conditioning WARNING! Turn off temporarily. Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. SNOW PLOW This could adversely affect the functioning of the Snow plows, winches, and other aftermarket equipment airbag system and you could be injured.
Page 390: Recreational Towing-Two Wheel Drive Models
388 STARTING AND OPERATING Towing Wheels OFF The Two-Wheel Four-Wheel Four-Wheel Drive Models With 4–LO Condition Ground Drive Models Drive Models Range Without 4–LO Range Dolly Tow Front NOT ALLOWED ALLOWED ALLOWED Rear NOT ALLOWED ALLOWED On Trailer Recreational Towing-Two Wheel Drive Models NOTE: •...
Page 391: Recreational Towing - Quadra-Trac I (Single-Speed Transfer Case) Four-Wheel Drive Models
STARTING AND OPERATING 389 3. Firmly apply the parking brake. Shift the transmission CAUTION! into PARK. Towing this vehicle in violation of the above require- 4. Turn the ignition OFF. ments can cause severe transmission and/or transfer 5. Properly secure the rear wheels to the dolly, following case damage.
Page 392 390 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • Tow only in a forward direction. Towing this vehicle disengages both the front and rear driveshafts from the backwards can cause severe damage to the transfer case. powertrain and will allow the vehicle to roll, even if the •...
Page 393 STARTING AND OPERATING 391 5. Using a ballpoint pen or similar object, push and hold 7. Shift the transmission into REVERSE. the recessed transfer case NEUTRAL (N) button (located 8. Release the brake pedal for five seconds and ensure that by the selector switch) for four seconds.
Page 394 392 STARTING AND OPERATING NOTE: Shifting Out Of NEUTRAL (N) • Steps 1 through 4 are requirements that must be met Use the following procedure to prepare your vehicle for before pushing the NEUTRAL (N) button, and must normal usage. continue to be met until the shift has been completed.
Page 395 STARTING AND OPERATING 393 13. Release the parking brake. 14. Shift the transmission into DRIVE, release the brake pedal, and check that the vehicle operates normally. NOTE: • Steps 1 through 5 are requirements that must be met before pushing the NEUTRAL (N) button, and must continue to be met until the shift has been completed.
Page 396: Driving Tips
394 STARTING AND OPERATING DRIVING TIPS On-Road Driving Tips Utility vehicles have higher ground clearance and a nar- rower track to make them capable of performing in a wide variety of off-road applications. Specific design character- istics give them a higher center of gravity than conven- tional passenger cars.
Page 397 STARTING AND OPERATING 395 3. Continue working your way across the vehicle, separat- 4. Locate the protective connector on the rear of the ing the remaining tabs from the slots in the upper fascia. bumper beam. NOTE: Do not allow the lower fascia to freely hang from the tabs in the opposite corner as damage to lower and upper fascia may result.
Page 398 396 STARTING AND OPERATING 6. Insert the wiring harness connector into the protective Lower Front Fascia Installation connector. NOTE: This will only work if you have a helper. 7. Store sensor and bracket in a safe place. 1. Starting at the center of the vehicle, engage a sufficient NOTE: All cruise control functions will be disabled when number of tabs to support the weight of the lower fascia the radar sensor is disconnected.
Page 399 STARTING AND OPERATING 397 Quadra-Lift — If Equipped WARNING! When off-roading, it is recommended that the lowest Do not drive in 4WD-LOW Range on dry pavement; useable vehicle height that will clear the current obstacle or driveline damage may result. 4WD-LOW Range locks terrain be selected.
Page 400 398 STARTING AND OPERATING Standing Water CAUTION! Avoid driving in standing water deeper than 20 inches When driving through water, do not exceed 5 mph (51 cm), and reduce speed appropriately to minimize wave (8 km/h). Always check water depth before entering as effects.
Page 401 STARTING AND OPERATING 399 Hill Climbing Remember, never drive diagonally across a hill always drive straight up or down. NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain forward motion by Before climbing a steep hill, shift the transmission to a turning the front wheels slowly.
Page 402 400 STARTING AND OPERATING • After extended operation in mud, sand, water, or similar After Driving Off-Road dirty conditions, have the radiator, fan, brake rotors, Off-road operation puts more stress on your vehicle than wheels, brake linings, and axle yokes inspected and does most on-road driving.
Page 403 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .403 ▫ Road Tire Installation ....430 ASSIST AND SOS MIRROR —...
Page 404 402 IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) .......443 EVENT DATA RECORDER (EDR) .
Page 405: Hazard Warning Flashers
IN CASE OF EMERGENCY 403 HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the Hazard Warning flasher.
Page 406 404 IN CASE OF EMERGENCY ASSIST Call WARNING! The ASSIST Button is used to automatically connect you to ALWAYS obey traffic laws and pay attention to the any one of the following support centers: road. ALWAYS drive safely with your hands on the •...
Page 407 IN CASE OF EMERGENCY 405 2. The LED light located between the ASSIST and SOS NOTE: buttons on the Rearview Mirror will turn green once a • Your vehicle may be transmitting data as authorized connection to a SOS operator has been made. by the subscriber.
Page 408 406 IN CASE OF EMERGENCY WARNING! WARNING! (Continued) may prevent your vehicle from sending a signal to • If anyone in the vehicle could be in danger (e.g., fire initiate an emergency call. To avoid interference that or smoke is visible, dangerous road conditions or can cause the SOS Call system to fail, never add location), do not wait for voice contact from an aftermarket equipment (e.g., two-way mobile radio,...
Page 409 IN CASE OF EMERGENCY 407 SOS Call System Limitations WARNING! (Continued) Vehicles sold in Mexico DO NOT have SOS Call system • The Occupant Restraint Control module turns on the capabilities. air bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.
Page 410 408 IN CASE OF EMERGENCY • Equipment malfunction at the SOS operator facility. reception, which can prevent your vehicle from placing an emergency call. An operable LTE (voice/data) or 4G • Operator error by the SOS operator. (data) network connection and a GPS signal is required •...
Page 411: Bulb Replacement
IN CASE OF EMERGENCY 409 BULB REPLACEMENT Replacement Bulbs Interior Bulbs Bulb Number Glove Compartment Lamp Grab Handle Lamp L002825W5W Overhead Console Reading Lamps VT4976 Rear Cargo Lamp 214–2 Visor Vanity Lamp V26377 Underpanel Courtesy Lamps Instrument Cluster (General Illumination) Telltale/Hazard Lamp Exterior Bulbs Bulb Number...
Page 412 410 IN CASE OF EMERGENCY Bulb Number Front Side Marker — If Equipped Premium Front Side Marker — If Equipped LED - (Service At Authorized Dealer) Front Park/Turn Lamp — If Equipped 7444NA (WY27/8W) Rear Body Side Turn Signal Lamps 7440NA (WY21W) Auxiliary Liftgate Tail Lamps LED - (Service At Authorized Dealer)
Page 413: Bulb Replacement
IN CASE OF EMERGENCY 411 Bulb Replacement Halogen Headlamps — If Equipped High Intensity Discharge Headlamps (HID) — If 1. Open the hood. Equipped 2. Turn the low or high beam bulb one–quarter turn The headlamps are a type of high voltage discharge tube. counterclockwise to remove from housing.
Page 414 412 IN CASE OF EMERGENCY CAUTION! CAUTION! (Continued) • Always use the correct bulb size and type for replace- Do not touch the new bulb with your fingers. Oil ment. An incorrect bulb size or type may overheat contamination will severely shorten bulb life. If the and cause damage to the lamp, the socket or the lamp bulb comes in contact with any oily surface, clean the wiring.
Page 415 IN CASE OF EMERGENCY 413 Rear Tail, Stop, and Turn Signal Lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. Rear Of Tail Lamp 1 — Rear Turn/Stop Bulb Socket 2 — LED Tail Connector – Do Not Remove 3 —...
Page 416 414 IN CASE OF EMERGENCY Rear Liftgate Mounted Tail Lamp Liftgate Lower Trim 3. Continue removing the trim. Rear Liftgate Tail Lamps 4. Disconnect the two trim panel lights. 1. Raise the liftgate. 5. Tail lamps are now visible. Rotate socket(s) counter 2.
Page 417 IN CASE OF EMERGENCY 415 Center High-Mounted Stop Lamp (CHMSL) The center high mounted stop lamp is an LED. Service at an authorized dealer. Rear Of Liftgate Tail Lamp 1 — Auxiliary LED Tail Connector – Do Not Remove 2 — Backup Bulb Socket Center High-Mounted Stop Lamp 6.
Page 418: Fuses
416 IN CASE OF EMERGENCY FUSES When a device does not work, you must check the fuse element inside the blade fuse for a break/melt. WARNING! Also, please be aware that when using power outlets for extended periods of time with the engine off may result in •...
Page 419: Underhood Fuses
IN CASE OF EMERGENCY 417 Underhood Fuses The Power Distribution Center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 420 418 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 40 Amp Green – Blower Motor Front 40 Amp Green – Body Controller #4/Exterior Lighting #1 30 Amp Pink – Headlamp Washer — If Equipped 20 Amp Blue – Headrest Solenoid —...
Page 421 IN CASE OF EMERGENCY 419 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Daytime Running Lights/Headlamp Leveling – 20 Amp Yellow Horn – 10 Amp Red Diagnostic Port – 10 Amp Red Integrated Central Stack/Climate Control – 20 Amp Yellow Air Suspension Control Module - If Equipped –...
Page 422 420 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 15 Amp Blue CD/DVD/Bluetooth Hands-free Module — If Equipped – 20 Amp Yellow Rear Wiper Motor – 15 Amp Blue Spotlight Feed — If Equipped – 20 Amp Yellow Fuel Pump Motor –...
Page 423 IN CASE OF EMERGENCY 421 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Air Suspension — If Equipped/Trailer Tow/Steering Column Control Module – 15 Amp Blue Instrument Panel Cluster F90/F91 – 20 Amp Yellow Power Outlet (Rear seats) Selectable –...
Page 424: Jacking And Tire Changing
422 IN CASE OF EMERGENCY CAUTION! WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The • When installing the power distribution center cover, vehicle could slip off the jack and fall on you. You it is important to ensure the cover is properly posi- could be crushed.
Page 425: Jack Location
IN CASE OF EMERGENCY 423 Jack Location Spare Tire Stowage The scissor-type jack and tire changing tools are located in The spare tire is stowed under the load floor in the rear the rear cargo area, below the load floor. cargo area and is secured to the body with a special wing nut.
Page 426: Jacking Instructions
424 IN CASE OF EMERGENCY 5. Turn the ignition OFF. WARNING! (Continued) 6. Block both the front and rear of the wheel • Block the wheel diagonally opposite the wheel to be diagonally opposite of the jacking position. raised. For example, if changing the right front •...
Page 427 IN CASE OF EMERGENCY 425 3. Assemble the jack and jacking tools. Jack Warning Label Jack And Tool Assembly CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1.
Page 428 426 IN CASE OF EMERGENCY Jacking Locations Lift Point Symbol On Sill Molding 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged.
Page 429 IN CASE OF EMERGENCY 427 CAUTION! Do NOT raise the vehicle by the body side sill mold- ing. Be sure the jack is placed in the proper engage- ment location on the inside of the panel. Damage of the vehicle may occur if the procedure is not properly followed.
Page 430 428 IN CASE OF EMERGENCY 8. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. CAUTION! Be sure to mount the inflatable spare tire with the valve stem facing outward.
Page 431 IN CASE OF EMERGENCY 429 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 9.
Page 432: Road Tire Installation
430 IN CASE OF EMERGENCY 5. After 25 miles (40 km), check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
Page 433: Preparations For Jump Start
IN CASE OF EMERGENCY 431 Preparations For Jump Start WARNING! The battery in your vehicle is located under the passenger’s • Take care to avoid the radiator cooling fan whenever front seat. There are remote terminals located under the the hood is raised. It can start anytime the ignition hood to assist in jump starting.
Page 434: Jump Starting Procedure
432 IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, park Connecting The Jumper Cables the vehicle within the jumper cables reach, apply the 1. Connect the positive (+) end of the jumper cable to the parking brake and make sure the ignition is OFF.
Page 435: Refueling In Emergency
IN CASE OF EMERGENCY 433 If frequent jump starting is required to start your vehicle CAUTION! you should have the battery and charging system tested at your authorized dealer. Do not run the booster vehicle engine above 2000 rpm since it provides no charging benefit, wastes fuel and CAUTION! can damage booster vehicle engine.
Page 436: If Your Engine Overheats
434 IN CASE OF EMERGENCY IF YOUR ENGINE OVERHEATS WARNING! In any of the following situations, you can reduce the You or others can be badly burned by hot engine potential for overheating by taking the appropriate action. coolant (antifreeze) or steam from your radiator. If you •...
Page 437: Manual Park Release
IN CASE OF EMERGENCY 435 MANUAL PARK RELEASE Follow these steps to use the Manual Park Release: 1. Firmly apply the parking brake. WARNING! 2. Open the center console and locate the Manual Park Always secure your vehicle by fully applying the Release cover, remove it by snapping the cover away parking brake before activating the Manual Park Re- from the console hinges.
Page 438 436 IN CASE OF EMERGENCY 3. Using a screwdriver or similar tool, push the metal latch in towards the tether strap. Released Position CAUTION! Release Latch Closing the armrest while the Manual Park Release is 4. While the metal latch is in the open position, simulta- activated may damage the Manual Park Release neously pull upwards on the tether strap until the lever mechanism, the transmission, and/or the armrest.
Page 439 IN CASE OF EMERGENCY 437 To Disengage The Manual Park Release Lever: 2. Once the tension has been released and the lever has been unlocked, be sure it is stowed properly and locks 1. To disengage the Manual Park Release, apply tension into position.
Page 440: Freeing A Stuck Vehicle
438 IN CASE OF EMERGENCY FREEING A STUCK VEHICLE WARNING! If your vehicle becomes stuck in mud, sand or snow, it can Fast spinning tires can be dangerous. Forces generated often be moved using a rocking motion. Turn the steering by excessive wheel speeds may cause damage, or even wheel right and left to clear the area around the front failure, of the axle and tires.
Page 441: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 439 NOTE: Vehicles equipped with Quadra-Lift must be CAUTION! (Continued) placed in Transport mode, before tying them down (from • Revving the engine or spinning the wheels too fast the body) on a trailer or flatbed truck. Refer to the section may lead to transmission overheating and failure.
Page 442 440 IN CASE OF EMERGENCY Four-Wheel Towing Wheels OFF Drive Models Four-Wheel Drive Models Two-Wheel Drive Models Condition The Ground Without 4WD With 4WD LOW Range LOW Range Flat Tow NONE IF transmission is operable: See Instructions • Transmission in NEUTRAL •...
Page 443: Two-Wheel Drive Models
IN CASE OF EMERGENCY 441 Without The Key Fob • The transmission must be in NEUTRAL. Refer to Manual Park Release in this section for instructions on Special care must be taken when the vehicle is towed with shifting the transmission to NEUTRAL when the engine the ignition in the LOCK/OFF mode.
Page 444: Four-Wheel Drive Models
442 IN CASE OF EMERGENCY Four-Wheel Drive Models CAUTION! (Continued) The manufacturer recommends towing with all wheels • Towing this vehicle in violation of the above require- OFF the ground. Acceptable methods are to tow the vehicle ments can cause severe transmission and/or transfer on a flatbed or with one end of vehicle raised and the case damage.
Page 445 IN CASE OF EMERGENCY 443 EVENT DATA RECORDER (EDR) CAUTION! This vehicle is equipped with an Event Data Recorder Tow hooks are for emergency use only, to rescue a (EDR). The main purpose of an EDR is to record data that vehicle stranded off road.
Page 447 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING ....447 ▫ Accessory Drive Belt Inspection ... .463 ▫...
Page 448 446 SERVICING AND MAINTENANCE ▫ Spare Tires — If Equipped ....496 ▫ Temperature Grades .....503 ▫...
Page 449: Scheduled Servicing
SERVICING AND MAINTENANCE 447 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 450 448 SERVICING AND MAINTENANCE Required Maintenance Refer to the Maintenance Plans on the following pages for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. •...
Page 451: Maintenance Plan
SERVICING AND MAINTENANCE 449 Maintenance Plan Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 452: Heavy Duty Use Of The Vehicle
450 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change transfer case fluid. Inspect and replace PCV valve if necessary.
Page 453: Engine Compartment
SERVICING AND MAINTENANCE 451 ENGINE COMPARTMENT 3.6L Engine 1 — Remote Jump Start Positive Terminal 6 — Air Cleaner Filter 2 — Power Distribution Center (Fuses) 7 — Washer Fluid Reservoir 3 — Engine Oil Dipstick 8 — Engine Oil Filter Access 4 —...
Page 454: L Engine
452 SERVICING AND MAINTENANCE 5.7L Engine 1 — Remote Jump Start Positive Terminal 6 — Air Cleaner Filter 2 — Power Distribution Center (Fuses) 7 — Washer Fluid Reservoir 3 — Engine Oil Dipstick 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 455: Checking Oil Level - Gasoline Engine
SERVICING AND MAINTENANCE 453 Checking Oil Level — Gasoline Engine Adding Washer Fluid To assure proper lubrication of your vehicle’s engine, the The instrument cluster display will indicate when the washer engine oil must be maintained at the correct level. Check fluid level is low.
Page 456: Maintenance-Free Battery
454 SERVICING AND MAINTENANCE Maintenance-Free Battery CAUTION! Your vehicle is equipped with a maintenance-free battery. • It is essential when replacing the cables on the You will never have to add water, nor is periodic mainte- battery that the positive cable is attached to the nance required.
Page 457: Engine Oil
SERVICING AND MAINTENANCE 455 American Petroleum Institute (API) Engine Oil WARNING! Identification Symbol You can be badly injured working on or around a motor vehicle. Only do service work for which you This symbol means that the oil has have the knowledge and the proper equipment. If you been certified by the American Pe- have any doubt about your ability to perform a service troleum Institute (API).
Page 458 456 SERVICING AND MAINTENANCE Engine Oil Viscosity (SAE Grade) — 3.6L Engine NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil. Failure to do so may result in improper opera- Mopar SAE 0W-20 engine oil approved to FCA Material tion of the Fuel Saver Technology.
Page 459: Engine Oil Filter
SERVICING AND MAINTENANCE 457 Disposing Of Used Engine Oil And Oil Filters WARNING! Care should be taken in disposing of used engine oil and The air induction system (air cleaner, hoses, etc.) can oil filters from your vehicle. Used oil and oil filters, provide a measure of protection in the case of engine indiscriminately discarded, can present a problem to the backfire.
Page 460 458 SERVICING AND MAINTENANCE Engine Air Cleaner Filter Removal 2. Lift the air cleaner cover to access the air cleaner filter. 1. Release the spring clips from the air cleaner cover. Open Air Cleaner Filter Assembly 1 — Air Cleaner Cover Air Cleaner Filter Cover 2 —...
Page 461: Air Conditioner Maintenance
SERVICING AND MAINTENANCE 459 3. Remove the air cleaner filter element from the housing 2. Install the air cleaner cover onto the housing assembly assembly. locating tabs. 3. Latch the spring clips and lock the air cleaner cover to the housing assembly. Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the...
Page 462 460 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — R–1234yf WARNING! (Continued) R–1234yf Air Conditioning Refrigerant is a hydrofluo- • The air conditioning system contains refrigerant un- roolefin (HFO) that is endorsed by the Environmental der high pressure. To avoid risk of personal injury or Protection Agency and is an ozone-friendly substance with damage to the system, adding refrigerant or any a low global-warming potential.
Page 463 SERVICING AND MAINTENANCE 461 The A/C air filter is located in the fresh air inlet behind the 2. There are glove compartment travel stops on both sides glove compartment. Perform the following procedure to of the glove compartment door, partially close the glove replace the filter: compartment door and push inward to release the glove compartment travel stop on one side and repeat this...
Page 464 462 SERVICING AND MAINTENANCE Right Side Of Glove Compartment A/C Air Filter Cover 1 — Glove Compartment Tension Tether 1 — Retaining Tab 2 — Glove Compartment Door 2 — Mid Way Snap 3 — Filter Cover Hinge 5. Remove the filter cover by disengaging the retaining tab 6.
Page 465: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 463 Accessory Drive Belt Inspection CAUTION! WARNING! The cabin air filter is identified with an arrow to indicate airflow direction through the filter. Failure to • Do not attempt to inspect an accessory drive belt properly install the filter will result in the need to with vehicle running.
Page 466: Body Lubrication
464 SERVICING AND MAINTENANCE • Noise (objectionable squeal, squeak, or rumble is heard or felt while drive belt is in operation) Some conditions can be caused by a faulty component such as a belt pulley. Belt pulleys should be carefully inspected for damage and proper alignment.
Page 467: Windshield Wiper Blades
SERVICING AND MAINTENANCE 465 The external lock cylinders should be lubricated twice a The wiper blades and wiper arms should be inspected year, preferably in the Fall and Spring. Apply a small periodically, not just when wiper performance problems amount of a high quality lubricant, such as Mopar Lock are experienced.
Page 468 466 SERVICING AND MAINTENANCE 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position. Wiper Blade With Release Tab In Unlocked Position 1 — Wiper Blade Wiper Blade With Release Tab In Locked Position 2 —...
Page 469 SERVICING AND MAINTENANCE 467 Installing The Front Wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper facing up and away from the wind- shield.
Page 470 468 SERVICING AND MAINTENANCE Rear Wiper Blade Removal/Installation 2. Lift the rear wiper arm fully off the glass. 1. Lift the rear wiper arm pivot cap away from the glass to allow the rear wiper blade to be raised off of the glass. NOTE: The rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first.
Page 471: Exhaust System
SERVICING AND MAINTENANCE 469 NOTE: Resistance will be accompanied by an audible Installing The Rear Wiper snap. 1. Lift the rear wiper arm pivot cap away from the glass to 4. Still grasping the bottom end of the wiper blade, move allow the rear wiper blade to be raised off of the glass.
Page 472 470 SERVICING AND MAINTENANCE If you notice a change in the sound of the exhaust system; CAUTION! or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; • The catalytic converter requires the use of unleaded have an authorized technician inspect the complete ex- fuel only.
Page 473: Cooling System
SERVICING AND MAINTENANCE 471 In unusual situations involving grossly malfunctioning WARNING! (Continued) engine operation, a scorching odor may suggest severe and • You or others can be badly burned by hot engine abnormal catalyst overheating. If this occurs, stop the coolant (antifreeze) or steam from your radiator.
Page 474 472 SERVICING AND MAINTENANCE Engine Coolant Checks Refer to the “Maintenance Plan” in this section for the proper maintenance intervals. Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where appli- Selection Of Coolant cable).
Page 475 SERVICING AND MAINTENANCE 473 Please review these recommendations for using Organic CAUTION! (Continued) Additive Technology (OAT) engine coolant (antifreeze) • Do not use water alone or alcohol-based engine that meets the requirements of FCA Material Standard coolant (antifreeze) products. Do not use additional MS.90032.
Page 476 474 SERVICING AND MAINTENANCE NOTE: WARNING! • It is the owner’s responsibility to maintain the proper • Do not open hot engine cooling system. Never add level of protection against freezing according to the engine coolant (antifreeze) when the engine is over- temperatures occurring in the area where the vehicle is heated.
Page 477 SERVICING AND MAINTENANCE 475 Coolant Level If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be The coolant bottle provides a quick visual method for safely driven. The vapor will soon dissipate. determining that the coolant level is adequate.
Page 478: Brake System
476 SERVICING AND MAINTENANCE • Do not change the thermostat for Summer or Winter Fluid Level Check — Brake Master Cylinder operation. If replacement is ever necessary, install ONLY The fluid level of the master cylinder should be checked the correct type thermostat. Other designs may result in whenever the vehicle is serviced, or immediately if the brake unsatisfactory engine coolant (antifreeze) performance, system warning light is on.
Page 479: Automatic Transmission
SERVICING AND MAINTENANCE 477 Automatic Transmission WARNING! (Continued) Selection Of Lubricant • To avoid contamination from foreign matter or mois- ture, use only new brake fluid or fluid that has been It is important to use the proper transmission fluid to in a tightly closed container.
Page 480 478 SERVICING AND MAINTENANCE Special Additives you notice fluid leakage or transmission malfunction, visit your authorized dealer immediately to have the transmis- The manufacturer strongly recommends against using any sion fluid level checked. Operating the vehicle with an special additives in the transmission. Automatic Transmis- improper fluid level can cause severe transmission dam- sion Fluid (ATF) is an engineered product and its perfor- age.
Page 481: Front/Rear Axle Fluid
SERVICING AND MAINTENANCE 479 Front/Rear Axle Fluid CAUTION! For normal service, periodic fluid level checks are not Do not overtighten the plugs as it could damage them required. When the vehicle is serviced for other reasons the and cause them to leak. exterior surfaces of the axle assembly should be inspected.
Page 482: Raising The Vehicle
480 SERVICING AND MAINTENANCE Drain Tire Markings First remove fill plug, then remove drain plug. Recom- mended tightening torque for drain and fill plugs is 15 to 25 ft lbs (20 to 34 N·m). CAUTION! When installing plugs, do not overtighten. You could damage them and cause them to leak.
Page 483 SERVICING AND MAINTENANCE 481 NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the • P (Passenger) — Metric tire sizing is based on U.S. size designation. Example: LT235/85R16. design standards.
Page 484 482 SERVICING AND MAINTENANCE EXAMPLE: 65, 85, 80 = Aspect ratio in percent (%) – Ratio of section height to section width of tire, or 10.5 = Section width in inches (in) R = Construction code – R means radial construction, or –...
Page 485 SERVICING AND MAINTENANCE 483 Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 486 484 SERVICING AND MAINTENANCE Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 487 SERVICING AND MAINTENANCE 485 Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 488 486 SERVICING AND MAINTENANCE Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 489 SERVICING AND MAINTENANCE 487 Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 490 488 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 491: Tires - General Information
SERVICING AND MAINTENANCE 489 Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 492 490 SERVICING AND MAINTENANCE Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 493 SERVICING AND MAINTENANCE 491 pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 494 492 SERVICING AND MAINTENANCE Run Flat Tires — If Equipped Refer to “Freeing A Stuck Vehicle” in “In Case Of Emer- gency” for further information. Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation WARNING! pressure.
Page 495 SERVICING AND MAINTENANCE 493 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 496 494 SERVICING AND MAINTENANCE Keep dismounted tires in a cool, dry place with as little It is recommended you contact your authorized tire dealer exposure to light as possible. Protect tires from contact with or original equipment dealer with any questions you may oil, grease, and gasoline.
Page 497: Tire Types
SERVICING AND MAINTENANCE 495 Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 498: Spare Tires - If Equipped
496 SERVICING AND MAINTENANCE Spare Tires — If Equipped Snow Tires Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 499 SERVICING AND MAINTENANCE 497 Compact Spare Tire — If Equipped WARNING! The compact spare is for temporary emergency use only. Compact and collapsible spares are for temporary You can identify if your vehicle is equipped with a compact emergency use only. With these spares, do not drive spare by looking at the spare tire description on the Tire more than 50 mph (80 km/h).
Page 500 498 SERVICING AND MAINTENANCE Do not install a wheel cover or attempt to mount a Limited Use Spare — If Equipped conventional tire on the collapsible spare wheel, since the The limited use spare tire is for temporary emergency use wheel is designed specifically for the collapsible spare tire.
Page 501: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 499 Wheel And Wheel Trim Care When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and All wheels and wheel trim, especially aluminum and wheel cleaning chemicals and equipment to prevent dam- chrome plated wheels, should be cleaned regularly using age to the wheels.
Page 502: Tire Chains (Traction Devices)
500 SERVICING AND MAINTENANCE Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 503: Tire Rotation Recommendations
SERVICING AND MAINTENANCE 501 NOTE: The premium Tire Pressure Monitor System will CAUTION! (Continued) automatically locate the pressure values displayed in the • Observe the traction device manufacturer’s instruc- correct vehicle position following a tire rotation. tions on the method of installation, operating speed, The suggested rotation method is the “rearward-cross”...
Page 504: Department Of Transportation Uniform Tire Quality Grades
502 SERVICING AND MAINTENANCE DEPARTMENT OF TRANSPORTATION UNIFORM Traction Grades TIRE QUALITY GRADES The Traction grades, from highest to lowest, are AA, A, The following tire grading categories were established B, and C. These grades represent the tire’s ability to stop by the National Highway Traffic Safety Administration.
Page 505: Temperature Grades
SERVICING AND MAINTENANCE 503 Temperature Grades STORING THE VEHICLE The Temperature grades are A (the highest), B, and C, If you are storing your vehicle for more than 21 days, we representing the tire’s resistance to the generation of recommend that you take the following steps to minimize heat and its ability to dissipate heat, when tested under the drain on your vehicle’s battery: controlled conditions on a specified indoor laboratory...
Page 506: Plastic And Coated Parts
504 SERVICING AND MAINTENANCE Plastic And Coated Parts Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents Use Mopar Total Clean to clean vinyl upholstery. or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. CAUTION! If the belts need cleaning, use a mild soap solution or •...
Page 507: Leather Parts
SERVICING AND MAINTENANCE 505 Leather Parts CAUTION! Mopar Total Clean is specifically recommended for leather Do not use Alcohol and Alcohol-based and/or Ketone upholstery. based cleaning products to clean leather seats, as Your leather upholstery can be best preserved by regular damage to the seat may result.
Page 509 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....508 ▫ Gasoline/Oxygenate Blends ....512 ▫...
Page 510: Identification Data
508 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the wind- shield. This number also is stamped on the right front floor, behind the right front seat.
Page 511: Brake System
TECHNICAL SPECIFICATIONS 509 In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 512 510 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the After 25 miles (40 km), check the lug nut/bolt torque to be tire and remove any corrosion or loose particles. sure that all the lug nuts/bolts are properly seated against the wheel.
Page 513: Fuel Requirements
TECHNICAL SPECIFICATIONS 511 FUEL REQUIREMENTS 5.7L Engine Do not use E-85 flex fuel or ethanol blends greater than 3.6L Engine 15% in this engine. Do not use E-85 flex fuel or ethanol blends greater than This engine is designed to meet all emis- 15% in this engine.
Page 514: Reformulated Gasoline
512 TECHNICAL SPECIFICATIONS Reformulated Gasoline Indiscriminate use of fuel system cleaning agents should be avoided. Many of these materials intended for gum and Many areas of the country require the use of cleaner burning varnish removal may contain active solvents or similar gasoline referred to as “Reformulated Gasoline”.
Page 515: Do Not Use E-85 In Non-Flex Fuel Vehicles
TECHNICAL SPECIFICATIONS 513 Do Not Use E-85 In Non-Flex Fuel Vehicles MMT In Gasoline Non-Flex Fuel Vehicles (FFV) are compatible with gasoline Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is containing up to 15% ethanol (E-15). Use of gasoline with a manganese-containing metallic additive that is blended higher ethanol content may void the New Vehicle Limited into some gasoline to increase octane.
Page 516: Carbon Monoxide Warnings
514 TECHNICAL SPECIFICATIONS Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to Carbon monoxide (CO) in exhaust gases is deadly. overheat. If you notice a pungent burning odor or Follow the precautions below to prevent carbon mon- some light smoke, your engine may be out of tune or oxide poisoning:...
Page 517: Fluid Capacities
TECHNICAL SPECIFICATIONS 515 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 3.6L and 5.7L Engines 24.6 Gallons 93.0 Liters Engine Oil With Filter 3.6L Engine (SAE 0W-20, API Certified) 6 Quarts 5.6 Liters 5.7L Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters Cooling System* 3.6L Engine (Mopar Antifreeze/Engine Coolant 10 Year/150,000 Mile 10.4 Quarts...
Page 518: Fluids And Lubricants
516 TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). Engine Oil – 3.6L Engine We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix.
Page 519 TECHNICAL SPECIFICATIONS 517 CAUTION! CAUTION! (Continued) and refilled with fresh OAT coolant (conforming to • Mixing of engine coolant (antifreeze) other than MS.90032), by an authorized dealer as soon as pos- specified Organic Additive Technology (OAT) en- sible. gine coolant (antifreeze), may result in engine dam- •...
Page 520: Chassis
518 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmis- sion Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion.
Page 521 MULTIMEDIA CONTENTS UCONNECT RADIOS ....521 ▫ Accessory Gauges ..... .573 PERSONALIZED MENU BAR .
Page 522 520 MULTIMEDIA ▫ Important Notes For Dual Video Screen System .583 ▫ Phone .......598 ▫...
Page 523: Uconnect Radios
MULTIMEDIA UCONNECT RADIOS 1. Press the “Apps ” button to open the App screen. For detailed information about your Uconnect radio, refer 2. Press and hold, then drag the selected App to replace an to your Uconnect Owner’s Manual Supplement. existing shortcut in the main menu bar.
Page 524 522 MULTIMEDIA The risk of unauthorized and unlawful access to your NOTE: vehicle systems may still exist, even if the most recent • FCA US LLC or your dealer may contact you directly version of vehicle software (such as Uconnect software) is regarding software updates.
Page 525: Uconnect Settings
MULTIMEDIA UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many fea- tures can vary by vehicle.
Page 526: Buttons On The Faceplate
524 MULTIMEDIA Buttons On The Faceplate Customer Programmable Features — Uconnect 5.0 Personal Settings Buttons on the faceplate are located below the Uconnect system in the center of the instrument panel. In addition, Push the MORE button on the faceplate to display the there is a Scroll/Enter control knob located on the right menu setting screen.
Page 527 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 528 526 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English/Français/Español) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Lan- guage”...
Page 529 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 530 528 MULTIMEDIA Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 531 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- ing On/Off — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is kept in memory from one ignition cycle to the next. If the system is turned OFF, it will re- main off when the vehicle is restarted.
Page 532 530 MULTIMEDIA Setting Name Selectable Options Forward Collision Warning-Plus (FCW+) Ac- tive Braking — If Equipped NOTE: The “Forward Collision Warning Plus (FCW+)” setting includes Advanced Brake Assist (ABA). The ABA applies ad- ditional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. Sound Only Sound and Display ParkSense —...
Page 533 MULTIMEDIA Setting Name Selectable Options Lane Departure Warning Early Medium Late (LDW) — If Equipped NOTE: The “Lane Depature Warning (LDW)” setting determines at what distance the LDW system will warn you, through steering wheel feedback, of a possible lane departure. Lane Departure Strength Medium High...
Page 534 532 MULTIMEDIA Setting Name Selectable Options Paddle Shifters Enable Disable Steering Feel Options Sport Normal Comfort NOTE: The “Steering Feel Options” setting will allow you to adjust the steering effort and feel. Press the “Comfort” button on the touchscreen to provide a balance of steering feel and steering effort. Press the “Normal” button on the touch- screen to provide greater steering feel, requiring greater steering effort.
Page 535 MULTIMEDIA Setting Name Selectable Options Headlight Illumina- 0 sec 30 sec 60 sec 90 sec tion On Approach NOTE: When this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the doors are unlocked with the key fob.
Page 536 534 MULTIMEDIA Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: The “Auto Door Locks” feature locks all doors automatically when the vehicle reaches a speed of 12 mph (20 km/h). Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit”...
Page 537 MULTIMEDIA Setting Name Selectable Options Remote Door Unlock/Door Driver Door All Doors Unlock NOTE: When “Driver” is selected, only the driver’s door will unlock on the first push of the key fob unlock button, you must push the key fob unlock button twice to unlock the passenger’s doors. When “All” is selected, all of the doors will unlock on the first press of the key fob unlock button.
Page 538 536 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 539 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 540 538 MULTIMEDIA Setting Name Selectable Options Auto Entry/Exit If Equipped NOTE: The “Auto Entry/Exit feature automatically lowers the vehicle ride height position when shifted into park, when it is selected. Compass Settings — If Equipped NOTE: Before compass calibration is performed, the com- pass variance zone should be set for best results.
Page 541 MULTIMEDIA Compass Variance Zone Map Compass Calibration Start NOTE: Press “Compass Calibration” on the touchscreen to enter calibration. To start calibration of the compass, press the “Yes” button on the touchscreen and complete one or more 360-degree turns (in an area free from large metal or me- tallic objects).
Page 542 540 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Adjustable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid” and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 543 MULTIMEDIA Setting Name Adjustable Options AUX Volume Offset — If Equipped NOTE: This feature provides the ability to tune the audio level for portable devices connected through the AUX input. Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Paired Phones...
Page 544 542 MULTIMEDIA Suspension After pressing the “Suspension” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto Entry/Exit Suspension NOTE: When the “Auto Entry/Exit Suspension” setting is selected, the vehicle automatically lowers from ride height posi- tion when the vehicle is shifted to park for easy entry/exit.
Page 545 MULTIMEDIA Setting Name Selectable Options Wheel Alignment Mode NOTE: The “Wheel Alignment Mode” setting prevents auto leveling of the air suspension while performing a wheel align- ment service. SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 546 544 MULTIMEDIA Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 547 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected, it will reset all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 548: Customer Programmable Features - Uconnect 8.4 Settings
546 MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options System Information System Software Information Screen NOTE: When this feature is selected, a “System Information” screen will appear, displaying the system software version. Customer Programmable Features —...
Page 549 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 550 548 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa- ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Language”...
Page 551 MULTIMEDIA Setting Name Selectable Options Navigation Turn-By-Turn In Cluster NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Phone Pop-ups Displayed in Cluster Units...
Page 552 550 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 553 MULTIMEDIA Setting Name Selectable Options Set Time Minutes NOTE: The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch- screen must be unchecked. Time Format 12hrs 24hrs Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 554 552 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- Near ing Sensitivity — If Equipped NOTE: The “Forward Collision Warning Plus (FCW+) Sensitivity” setting determines at what relative distance the vehicle directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly in front of you, based on the option is selected.
Page 555 MULTIMEDIA Setting Name Selectable Options Power Steering Sport Normal Comfort NOTE: The “Steering Feel Options” setting will allow you to adjust the steering effort and feel. Press the “Comfort” button on the touchscreen to provide a balance of steering feel and steering effort. Press the “Normal” button on the touch- screen to provide greater steering feel, requiring greater steering effort.
Page 556 554 MULTIMEDIA Setting Name Selectable Options Tilt Side Mirrors in Re- verse NOTE: When this feature is selected, the exterior side view mirrors will tilt downward when the ignition is in the RUN posi- tion and the transmission gear selector is in the REVERSE position. The mirrors will move back to their previous po- sition when the transmission is shifted out of REVERSE.
Page 557 MULTIMEDIA Setting Name Selectable Options ParkView Backup Camera Active Guide Lines — If Equipped NOTE: The “ParkView Backup Camera Active Guide Lines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 558 556 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 559 MULTIMEDIA Setting Name Selectable Options Daytime Running Lights — If Equipped Flash Lights With Lock Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: When the “Auto Door Locks”...
Page 560 558 MULTIMEDIA Setting Name Selectable Options Sound Horn With Lock 1st Press 2nd Press Sound Horn With Remote Start 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When Driver Door is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first press of the key fob unlock button.
Page 561 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked to Key Fob — If Equipped NOTE: This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steer- ing column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle. Power Lift Gate Alert —...
Page 562 560 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seat Engine Off Power 0 sec 45 sec 5 min 10 min Delay Headlight Off Delay 0 sec 30 sec...
Page 563 MULTIMEDIA Setting Name Selectable Options Display Suspension Messages Warings NOTE: The “Suspension Display Messages” setting allows you to choose whether you want the Suspension system to display all suspension messages, or to only display suspension warnings. Tire Jack Mode NOTE: When the “Tire Jack Mode”...
Page 564 562 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 565 MULTIMEDIA Setting Name Selectable Options AutoPlay NOTE: The “AutoPlay” setting, when activated, automatically starts playing music off of a connect device as soon as it is connected. Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Do Not Disturb...
Page 566 564 MULTIMEDIA Setting Name Selectable Options Paired Audio Sources List Of Paired Audio Sources NOTE: This feature shows which Audio Sources are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement. Display Phone Info In Cluster SiriusXM Setup —...
Page 567 MULTIMEDIA Setting Name Selectable Options Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning. This feature allows you to select the channels you would like to skip. Subscription Info Sirius ID NOTE:...
Page 568 566 MULTIMEDIA Radio Setup — If Equipped After pressing the “Radio Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Regional — If Equipped NOTE: When the “Regional” feature is selected, it forces regional service-following enabling automatic switching to network stations.
Page 569 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected it will reset all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 570: Off Road Pages - If Equipped
568 MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options System Information System Software Information Screen NOTE: When this feature is selected, a “System Information” screen will appear, displaying the system software version. OFF ROAD PAGES —...
Page 571: Off Road Pages Status Bar
MULTIMEDIA Off Road Pages has the following selectable pages: • Drivetrain • Suspension • Pitch and Roll — If Equipped • Accessory Gauge • Selec-Terrain — If Equipped Off Road Pages Status Bar The Off Road Pages Status Bar is located along the bottom of Off Road Pages and is present in each of the five selectable page options.
Page 572: Drivetrain
570 MULTIMEDIA • Current Altitude of the vehicle Drivetrain • Status of Hill Descent/Selec-Speed Control and Selected The Drivetrain page displays information concerning the Speed in MPH (km/h) vehicle’s drivetrain. The following information is displayed: • Steering angle in degrees •...
Page 573: Suspension
MULTIMEDIA Suspension The Suspension page displays information concerning the vehicle’s suspension. The following information is displayed: • Suspension Articulation Indicator • Current Ride Height Status — If Equipped • Normal • Off Road 1 • Off Road 2 • Entry/Exit •...
Page 574: Pitch And Roll - If Equipped
572 MULTIMEDIA Pitch And Roll — If Equipped NOTE: The wheel articulation will be represented by a yellow color in the Suspension Articulation Indicator. If Ride Height The Pitch And Roll page displays the vehicle’s current is adjusted, the Ride Height indicator on the screen will switch pitch (angle up and down) and roll (angle side to side) in to the appropriate height and the Suspension Articulation degrees.
Page 575: Accessory Gauges
MULTIMEDIA Accessory Gauges Selec-Terrain — If Equipped The Accessory Gauges page displays the current status of The Selec-Terrain page displays the current Selec-Terrain the vehicle’s Coolant Temperature, Oil Temperature, Oil mode through a high resolution image. Adjusting the Pressure (Gas Vehicles Only), Transmission Temperature, Selec-Terrain mode will alter the image on the screen.
Page 576: Steering Wheel Audio Controls - If Equipped
574 MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — IF NOTE: While in the Selec-Terrain pages, the Off Road EQUIPPED Pages Status Bar will also display the current Selec-Terrain mode. The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
Page 577: Radio Operation
MULTIMEDIA Pushing the center button will make the radio switch If you push the switch up or down twice, it plays the between the various modes available (AM/FM/SXM/CD/ second track; three times, it will play the third, etc. AUX/VES, etc.). IPOD/USB/MP3 CONTROL —...
Page 578: Getting Started
576 MULTIMEDIA Getting Started • Turn on the Rear Seat Entertainment system by pushing the power button on the remote control. • Screen(s) located in the rear of front seats: Open the LCD screen cover by lifting up on cover. •...
Page 579: Dual Video Screen
MULTIMEDIA • With the Dual Video Screen System, Channel 1 (Rear 1) on the remote control and headphones, refers to Screen 1 (driver’s side) and Channel 2 (Rear 2) on the Remote Control and Headphones refers to Screen 2 (passenger side).
Page 580: Blu-Ray Disc Player
578 MULTIMEDIA Blu-ray Disc Player 2. To watch a Blu-ray disc on Rear 1 for driver’s side rear passengers, ensure the Remote Control and Headphone Play A Blu-ray Disc switch is on Rear 1. The Blu-ray disc player is located in the center console. 3.
Page 581 MULTIMEDIA Using The Touchscreen Radio 3. RSE Mute Mute rear headphones for the current ignition cycle. Press- ing mute again will unmute rear headphones. 4. RSE Remote Control Lock Out Press to enable/disable remote control functions. 5. RSE Channel 2 Mode Indicates the current source for Screen 2/Channel 2.
Page 582: Play Video Games
580 MULTIMEDIA Play Video Games 8. RSE Mode Select this button to change source for the active (high- Connect the video game console to the Audio/Video lighted) rear Screen/Channel on the rear media control RCA/HDMI input jacks located on the side of each seat. screen.
Page 583: Play A Dvd/Blu-Ray Disc Using The Touchscreen Radio
MULTIMEDIA When connecting an external source to the AUX/HDMI 3. To watch a DVD/Blu-ray Disc on Rear 2 (passenger’s input, ensure to follow the standard color coding for the side rear passenger), ensure the Remote Control and audio/video jacks: Headphone channel selector switch is on Rear 2. 1.
Page 584 582 MULTIMEDIA Using The Touchscreen Radio Controls 1. Press the Media button on the Uconnect radio touch- screen. 2. Press the Rear Media button to display the Rear Media Control screen. Rear Seat Entertainment Source Screen NOTE: Pressing the screen on the radio while a DVD or Blu-ray Disc is playing, brings up the basic remote control functions for DVD play such as scene selection, Play, Pause, FF, RW, and Stop.
Page 585: Important Notes For Dual Video Screen System
MULTIMEDIA Important Notes For Dual Video Screen System Blu-ray Disc Player Remote Control — If Equipped • The Rear Seat Entertainment System is able to transmit two channels of stereo audio and video simultaneously. • The Blu-ray Disc Player can play CDs, DVDs and Blu-ray Discs.
Page 586 584 MULTIMEDIA 3. SOURCE — Push to enter Source Selection screen. 11. KEYPAD — Push to navigate chapters or titles. 4. Channel/Screen Selector Switch — Indicates which 12. ▪ (Stop) — Stops disc play. channel is being controlled by the remote control. When —...
Page 587: Headphones Operation
MULTIMEDIA Headphones Operation Controls The headphones receive two separate channels of audio The headphone power indicator and controls are located using an infrared transmitter from the video screen. on the right ear cup. If no audio is heard after increasing the volume control, NOTE: The rear video system must be turned on before verify that the screen is turned on, the channel is not muted sound can be heard from the headphones.
Page 588: Replacing The Headphone Batteries
586 MULTIMEDIA Accessibility — If Equipped 2. Push the SOURCE button on the remote control. Accessibility is a feature of the DVD/Blu-ray system that 3. Pushing the SOURCE button will advance to the next announces a function prior to performing the action. For mode.
Page 589 MULTIMEDIA What Does This Warranty Not Cover? This warranty does replace any discontinued Product with a comparable model. not cover any damage or defect that results from misuse, THIS WARRANTY IS THE SOLE WARRANTY FOR THIS abuse or modification of the Product other than by Un- PRODUCT, SETS FORTH YOUR EXCLUSIVE REMEDY RE- wired.
Page 590 588 MULTIMEDIA Display Settings To change the settings, push the remote control’s naviga- tion buttons ( , ) to select an item, then push the remote control’s navigation buttons ( , ) to change the value for the currently selected item. To reset all values back to the original settings, select the Default Settings menu option and push the remote control’s ENTER/OK button.
Page 591 MULTIMEDIA If the screen is closed and there is no audio heard, verify DVD Audio Support that the headphones are turned on (the ON indicator is When a DVD-Audio disc is inserted in the Blu-ray Disc illuminated) and the headphone selector switch is on the player, the DVD-Audio title on the disc is played by default desired channel.
Page 592 590 MULTIMEDIA • Open sessions are ignored. Only sessions that are closed Compressed Audio Files (MP3 and WMA) are playable. The Blu-ray Disc player is capable of playing MP3 • For multi-session CDs that contain only multiple CD- (MPEG-1 Audio Layer 3) and WMA (Windows Media Audio sessions, the player will renumber the tracks so Audio) files from a CD Data disc (usually a CD-R or each track number is unique.
Page 593 MULTIMEDIA • If you are creating your own files, the recommended The Blu-ray Disc player may shut down during extremely fixed bit rate for MP3 files is between 96 and 192Kbps hot conditions, such as when the vehicle’s interior tem- and the recommended fixed bit rate for WMA files is perature is above 120°...
Page 594: Radio Operation And Mobile Phones
592 MULTIMEDIA RADIO OPERATION AND MOBILE PHONES The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is Under certain conditions, the mobile phone being on in far less than the electromagnetic energy emitted by wire- your vehicle can cause erratic or noisy performance from less devices such as mobile phones.
Page 595: Tips
MULTIMEDIA UCONNECT VOICE RECOGNITION QUICK TIPS NOTE: • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 596: Get Started
594 MULTIMEDIA Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions. 2. Reduce background noise. Wind and passenger conver- sations are examples of noise that may impact recogni- tion.
Page 597: Basic Voice Commands
MULTIMEDIA Push the VR button . After the beep, say • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands • Repeat to listen to the system prompts again Notice the visual cues that inform you of your voice recognition system’s status.
Page 598: Radio
596 MULTIMEDIA Push the VR button . After the beep, say • Tune to ninety-five-point-five FM • Tune to Satellite Channel Hits 1 TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say “Help.”...
Page 599: Media
MULTIMEDIA • Change source to Bluetooth • Change source to AUX • Change source to USB • Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play genre Classical TIP: Press the Browse button on the touchscreen to see all of the music on your AUX or USB device.
Page 600: Phone
598 MULTIMEDIA • Call John Smith • Dial 123-456-7890 and follow the system prompts • Redial (call previous outgoing phone number) • Call back (call previous incoming phone number) TIP: When providing a Voice Command, push the Phone button and say “Call,” then pronounce the name exactly as it appears in your phone book.
Page 601: Voice Text Reply
MULTIMEDIA 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay. Where are you? I will be <number>...
Page 602: Climate (8.4/8.4 Nav)
600 MULTIMEDIA Climate (8.4/8.4 NAV) Apple iPhone iOS 6 or later supports reading incoming text messages only. To enable this feature on your Apple Too hot? Too cold? Adjust vehicle temperatures hands-free iPhone, follow these four simple steps: and keep everyone comfortable while you keep moving ahead.
Page 603: Navigation (8.4 /8.4 Nav)
MULTIMEDIA Navigation (8.4 /8.4 NAV) TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice The Uconnect navigation feature helps you save time and Command will not work to adjust the heated seats or become more productive when you know exactly how to steering wheel if equipped.
Page 604: Uconnect Access (8.4/8.4 Nav)
602 MULTIMEDIA Uconnect Access (8.4/8.4 NAV) TIP: To start a POI search, push the VR button . After the beep, say: “ Find nearest coffee shop.” WARNING! ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X(voice/data) or 3G(data) network connection.
Page 605: Register (8.4/8.4 Nav)
MULTIMEDIA Register (8.4/8.4 NAV) NOTE: Uconnect Access is available only on equipped vehicles purchased within the continental United States, To unlock the full potential of Uconnect Access in your Alaska and Hawaii. Services can only be used where vehicle, you first need to register with Uconnect Access. coverage is available;...
Page 606: Vehicle Health Alert
604 MULTIMEDIA Signing up is easy! Simply follow the steps above. Or, press the “Apps ” button on the touchscreen to “Register By Web” to complete the process using your smartphone or computer. For further information, please visit DriveUconnect.com. Vehicle Health Alert Your vehicle will send you an email alert if it senses a problem under the hood with one of your vehicles key systems.
Page 607: Voice Texting (8.4/8.4 Nav)
MULTIMEDIA • Press the “Location” button on the bottom menu bar of Apple iPhone iOS6 or later supports reading incoming text the app to bring up a map to locate your vehicle or send messages only. To enable this feature on your Apple a location to your Uconnect Navigation using Vehicle iPhone, follow these four simple steps: Finder and Send ‘n Go , if equipped.
Page 608: Yelp (8.4/8.4 Nav)
606 MULTIMEDIA TIP: TIP: Once you perform a search, you can reorganize the results by selecting either the Best Match, Rating or Dis- • Voice Texting is not compatible with iPhone, but if your tance tab on the top of the touchscreen display. vehicle is equipped with Siri Eyes Free, you can use your voice to send a text message.
Page 609: Siriusxm Travel Link (8.4/8.4 Nav)
MULTIMEDIA SiriusXM Travel Link (8.4/8.4 NAV) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4 NAV system.
Page 610 608 MULTIMEDIA To enable Siri push and hold, then release the Uconnect Getting Started Voice Recognition (VR) button on the steering wheel. After Ensure Siri is enabled on your iPhone. you hear a double beep you can ask Siri to play podcasts and music, get directions, read text messages and many other useful requests.
Page 611 MULTIMEDIA • Read text message from Sarah • Take me to the nearest coffee shop NOTE: • Speak clearly at a normal pace and volume while facing straight ahead to ensure your command is understood. • Siri is available on iPhone 4S and later. Voice Recognition/Siri Buttons 1 —...
Page 612: Do Not Disturb
610 MULTIMEDIA Do Not Disturb General Information With Do Not Disturb, you can disable notifications from The following regulatory statement applies to all Radio incoming calls and texts, allowing you to keep your eyes Frequency (RF) devices equipped in this vehicle: on the road and hands on the wheel.
Page 613: Additional Information
MULTIMEDIA Additional Information 3. Do not apply paper or tape to the disc; avoid scratching the disc. © 2017 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner 4. Do not use solvents such as benzene, thinner, cleaners, Connect is a trademark of FCA US LLC.
Page 615 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ......614 Impaired (TDD/TTY) .
Page 616: Suggestions For Obtaining Service For Your Vehicle
614 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 617: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 615 In Mexico Contact Any communication to the manufacturer’s customer center should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 618: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
616 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech and an Owner Identification Card in the mail within three Impaired (TDD/TTY) weeks of the vehicle delivery date. If you have any questions about the service contract, call the manufactur- To assist customers who have hearing difficulties, the er’s Service Contract National Customer Hotline at 1-800- manufacturer has installed special TDD (Telecommunica-...
Page 619: Warranty Information
CUSTOMER ASSISTANCE 617 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 620: In Canada
618 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 621 INDEX...
Page 622 620 INDEX About Your Brakes ......509 Air Conditioning Filter ....94, 457, 460 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 623 INDEX 621 Adding Fluid ......478, 518 Anti-Lock (ABS) ......509 Fluid And Filter Changes .
Page 624 622 INDEX Chains, Tire ......500 Compact Spare Tire ......497 Changing A Flat Tire .
Page 625 INDEX 623 Dipsticks Hazard Warning Flasher ....403 Oil (Engine) ......453 Jacking .
Page 626 624 INDEX Starting ......265, 266 Folding Rear Seat......43, 46 Engine Oil Viscosity.
Page 627: Introduction
INDEX 625 Fuses ........416 Hitches Trailer Towing ......378 Garage Door Opener (HomeLink) .
Page 628 626 INDEX Key Fob Brake Assist Warning ..... .188 Arm The Alarm ......34 Brake Warning .
Page 629 INDEX 627 Vanity Mirror ......70 Mini-Trip Computer......148 Warning (Instrument Cluster Description) .
Page 630 628 INDEX Identification Logo ..... . .455 Power Materials Added To ..... . .456 Brakes .
Page 631 INDEX 629 Radial Ply Tires ......491 Programming Additional Key Fobs ..24, 32 Radiator Cap (Coolant Pressure Cap).
Page 632 630 INDEX Seat Belt Untwisting Procedure .....220 Adjustable Upper Shoulder Belt Anchorage ..220 Seats .......43, 47, 52 Automatic Locking Retractor (ALR) .
Page 633 INDEX 631 Automatic Transmission ....274, 277 Starting And Operating ....265, 266 Shoulder Belts .
Page 634 632 INDEX Tire Markings ......480 Trailer Towing ......383 Tires .
Page 635 INDEX 633 Transfer Case ......479 Vehicle Loading ......374, 486 Maintenance .
Page 636 634 INDEX Fluid ....... . .453 Windshield Wiper Blades .....465 Windshield Wipers .
Page 637 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Jeep Grand Cherokee 2017 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Grand Cherokee 2017

Summary of Contents for Jeep Grand Cherokee 2017