Dual Mono Setup; Lfe Attenuator Setup; Sr+ Setup For Pioneer Plasma Displays; Video Converter Setup - Pioneer VSX-1016TXV-K Operating Instructions Manual

Other Settings
09

Dual Mono Setup

• Default setting: CH1
You can specify how dual mono encoded Dolby Digital
and DTS soundtracks should be played. Dual mono is not
widely used, but is sometimes necessary when two
languages need to be sent to separate channels.
1 Select 'Dual Mono Setup' from the Other Setup
menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
e.Video Conv. Setup
2 Choose the setting that you want.
• CH1 – Only channel 1 is played
• CH2 – Only channel 2 is played
• CH1 CH2 – Both channels are played through the
front speakers
3 When you're finished, press RETURN .
You return to the Other Setup menu.

LFE Attenuator Setup

• Default setting: ATT 0dB
Some Dolby Digital and DTS audio sources include ultra-
low bass tones. Set the LFE attenuator as necessary to
prevent the ultra-low bass tones from distorting the
sound from the speakers.
1 Select 'LFE ATT Setup' from the Other Setup menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
e.Video Conv. Setup
2 Choose the setting that you want.
• ATT 0dB – No limiting (recommended)
• ATT 10dB – 10 dB of limiting
• LFE OFF – No sound from LFE channel
3 When you're finished, press RETURN .
You return to the Other Setup menu.

SR+ Setup for Pioneer plasma displays

• Default setting: OFF (all settings)
Make the following settings if you have connected a
Pioneer plasma display to this receiver using an SR+
cable. Note that the number of settings available will
depend on the plasma display you've connected.
See also Using this receiver with a Pioneer plasma display
on page 44.
48
En
6b.Dual Mono Setup
Dual Mono [ CH1
:Return :Finish
6c. LFE ATT Setup
LFE ATT ATT 0dB
:Return :Finish
1 Select 'SR+ Setup' from the Other Setup menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
e.Video Conv. Setup
:Return
2 Select the 'PDP Volume Control' setting you want.
• OFF – The receiver does not control the volume of the
plasma display
• ON – When the receiver is switched to one of the inputs
that use the plasma display (DVD/LD, or another
function below), the volume on the plasma display is
muted so only sound from the receiver is heard.
3 Assign any input source connected to the plasma
display to the corresponding input number.
This matches the receiver's input source with a numbered
video input on the plasma display. For example, assign
DVD/LD to input-2 if you have connected your DVD video
output to video input 2 on the plasma display.
• The Monitor Out should be set to the input that you've
used to connect this receiver to your plasma display.
6d.SR + Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD OFF
TV/SAT [ OFF ]
DVR 1 [ OFF ]
DVR 2 [ OFF ]
VIDEO [ OFF ]
Monitor Out [ OFF ]
:Finish
4 When you're finished, press RETURN .
You return to the Other Setup menu.

Video Converter Setup

• Default setting: ON
The video converter allows you to see analog video
sources through all of this receiver's MONITOR VIDEO
OUT jacks. Note that the converter gives priority to
component, S-video, then composite (in that order). See
About the video converter on page 12 for more on this.
1 Select 'Video Conv. Setup' from the Other Setup
menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
e.Video Conv. Setup
:Return
2 Choose the setting that you want.
• ON – All analog video signals are output from the
MONITOR VIDEO OUT jacks.
• OFF – No conversion between video formats.
3 When you're finished, press RETURN .
You return to the Other Setup menu.
6d.SR + Setup
PDP Volume Control
OFF
PDP Input Select
DVD/LD [ OFF ]
TV/SAT [ OFF ]
DVR 1 [ OFF ]
DVR 2 [ OFF ]
VIDEO [ OFF ]
Monitor Out [ OFF ]
:Finish
6d.SR + Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-2
TV/SAT [ OFF ]
DVR 1 [ OFF ]
DVR 2 [ OFF ]
VIDEO [ OFF ]
Monitor Out [ OFF ]
:Finish
6e. Video Converter Setup
Video Conv. ON
:Finish