Zone Audio Setup; Sr+ Setup For Pioneer Flat Panel Tvs; Flicker Reduction Setup - Pioneer Elite SC-07 Operating Instructions Manual

Other Settings

ZONE Audio Setup

If you've made MULTI-ZONE connections (see MULTI-
ZONE listening on page 66), you may need to specify your
volume setting.
1 Select 'ZONE Audio Setup' from the Other Setup
menu.
4d.Other Setup
A/V RECEIVER
1. Multi Ch In Setup
2. ZONE Audio Setup
3. SR+ Setup
4. HDMI Control Setup

5. Flicker Reduction Setup

Exit Return
2 Select the volume level setting of ZONE 2 and
1
ZONE 3.
• Variable – Use this setting if you've connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receiver's controls to adjust the volume.
• Fixed – Use this setting if you've connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receiver's volume controls.
With the Fixed setting, the source is sent from this
receiver at maximum volume, so make sure the volume is
quite low in the sub zone at first, and then experiment to
find the correct level.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.

SR+ Setup for Pioneer flat panel TVs

Make the following settings if you have connected a
Pioneer flat panel TV to this receiver using an SR+ cable.
Note that the number of function settings available will
depend on the flat panel TV you've connected.
See also Using this receiver with a Pioneer flat panel TV on
page 70 and Using the SR+ mode with a Pioneer flat panel
TV on page 71.
1 Select 'SR+ Setup' from the Other Setup menu.
4d.Other Setup
A/V RECEIVER
1. Multi Ch In Setup
2. ZONE Audio Setup
3. SR+ Setup
4. HDMI Control Setup
5. Flicker Reduction Setup
Exit Return
2 Select the 'PDP Volume Control' setting you want.
• OFF – The receiver does not control the volume of the
flat panel TV.
Note
1 If you selected ZONE 2 in the Surround back speaker setting on page 56, you won't be able to change the volume level.
4d2.ZONE Audio Setup
A/V RECEIVER
ZONE 2 Volume Level : Variable
ZONE 3 Volume Level : Variable
Exit Finish
4d3.SR+ Setup
A/V RECEIVER
PDP Volume Control : OFF
Monitor Out Connect : OFF
Exit Finish
• ON – When the receiver is switched to one of the
inputs that use the flat panel TV (DVD, for example),
the volume on the flat panel TV is muted so only
sound from the receiver is heard.
3 Assign any input source connected to the flat panel
TV to the corresponding input number.
This matches the receiver's input source with a
numbered video input on the flat panel TV. For example,
assign DVD to input-2 if you have connected the your
DVD video output to video input 2 on the flat panel TV.
• The Monitor Out Connect should be set to the input
that you've used to connect this receiver to your flat
panel TV.
4d3.SR+ Setup
A/V RECEIVER
PDP Volume Control :
Monitor Out Connect :
Exit
4 When you're finished, press RETURN.
You will return to the Other Setup menu.
Flicker Reduction Setup
• Default setting: 4
The OSD's resolution can be increased. If you feel the
OSD is hard to see, try changing this setting. Note that
the resolution in this setting only affects the OSD; it has
no influence on the video output.
1 Select 'Flicker Reduction Setup' from the Other
Setup menu.
4d.Other Setup
A/V RECEIVER
1. Multi Ch In Setup
2. ZONE Audio Setup
3. SR+ Setup
4. HDMI Control Setup
5. Flicker Reduction Setup
Exit Return
2 Select the Flicker Reduction setting you want.
3 When you're finished, press RETURN.
You will return to the Other Setup menu.
OFF
OFF
Finish
4d5.Flicker Reduction Setup
A/V RECEIVER
Flicker Reduction : 4
Exit Finish
12
95
En