Page 1
TH-A75 SERVICE MANUAL DVD DIGITAL CINEMA SYSTEM 22009 2003 TH-A75 SP-XSA75 AUDIO VCR/DBS FM/AM VCR 1 AUDIO ANGLE SUBTITLE DECODE TOP MENU MENU RETURN DIGEST SP-XCA75 SURROUND SOUND CONTROL EFFECT S.WFR CENTER TEST Ð Ð SLEEP SETTING SURR-L S-BACK SURR-R Ð...
TH-A75 SECTION 1 Important Safety Precautions 1.1 Safety Precautions (1) This design of this product contains special hardware and exposed metal part and a known good earth ground. many circuits and components specially for safety purposes. Measure the AC voltage across the resistor with the AC For continued protection, no changes should be made to the voltmeter.
Page 3
TH-A75 1.5 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
Page 4
TH-A75 1.8 Important for laser products (1) CLASS 1 LASER PRODUCT (5) CAUTION : If safety switches malfunction, the laser is able (2) DANGER : Invisible laser radiation when open and inter to function. lock failed or defeated. Avoid direct exposure to beam.
TH-A75 SECTION 2 Disassembly method 2.1 Main body section 2.1.1 Removing the top cover (See Figs.1 to 4.) (1) From the right and left sides of the main body, remove the four screws A attaching the top cover. (See Figs.1 and 2.) (2) From the back side of the main body, remove the two screws B attaching the top cover.
Page 6
TH-A75 2.1.2 Removing the front panel assembly (See Figs.5 to 8.) • Remove the top cover. Chassis base (1) From the left side of the main body, push the section b of the slide cam using the screw driver, etc. (See Fig.5.) (2) Pull out the tray.
Page 7
TH-A75 2.1.3 Removing the DVD mechanism assembly (See Fig.9.) 2.1.4 Removing the DSP board (See Figs.10 and 11.) • Remove the top cover. • Remove the top cover. • Remove the front panel assembly. (1) From the top side of the main body, disconnect the card (1) From the top side of the main body, remove the barrier.
Page 8
TH-A75 2.1.6 Removing the main board (See Figs.12 and 13.) 2.1.7 Removing the amplifier board (See Figs.14 to 16.) • Remove the top cover. • Remove the top cover. • Remove the DSP board. (1) From the top side of the main body, disconnect the card •...
TH-A75 2.1.8 Removing the fan motor (See Figs.17 and 18.) 2.1.9 Removing the power board (See Fig.19.) • Remove the top cover. • Remove the top cover. • Remove the amplifier board. • Remove the amplifier board. (1) From the top side of the main body, remove the fan cover.
Page 10
TH-A75 2.2 Front panel assembly section 2.3 DVD mechanism section • Remove the top cover. • Remove the top cover. • Remove the front panel assembly. • Remove the DVD mechanism assembly. 2.2.1 Removing the jack board (See Fig.1.) 2.3.1 Removing the tray (See Figs.1 and 2.)
TH-A75 2.3.3 Removing the tray (See Fig.3.) 2.3.4 Removing the clamper base (See Fig.4.) (1) From the bottom side of the DVD mechanism assembly, (1) From the top side of the DVD mechanism assembly, re- disconnect the card wires from the connectors CN201 and move the four screws A attaching the clamper base.
Page 12
TH-A75 2.3.6 Removing the motor (See Fig.6.) 2.3.8 Removing the DVD pickup unit (See Figs.8 to 10.) • Remove the clamper base. • Remove the DVD servo board. • Remove the tray drive board. • Remove the clamper base. (1) From the top side of the DVD mechanism assembly, re- •...
Page 13
TH-A75 DVD pickup unit Section i Section h Section i Shaft Shaft Section h Section g Fig.9 SW. actuator Section DVD traverse mechanism assembly DVD pickup unit Fig.11 Shaft Section k Section j Lead screw Fig.10 DVD pickup unit Fig.12...
Page 14
TH-A75 2.3.10 Removing the spindle motor board (See Figs.13 and 2.3.11 Removing the feed motor (See Figs.15 to 17.) 14.) • Remove the DVD servo board. • Remove the DVD servo board. • Remove the clamper base. • Remove the clamper base.
(1) Power to on then mode to DVD. (2) Set the recorded disc. (Down loaded the up grade program "TH-A75 -Firmware Update Procedure" from Audio Products DIV. Technological Material of JS-Net .) (3) FL indicate "UPGRADE", press cursol key of the remote controller.
TH-A75 SECTION 4 Description of major ICs UPD784215AGC194 (IC531) : CPU • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function HREQ I HREQ - Not use O Slave select - +3.0V 50,51 - Not use...
Page 23
TH-A75 4.8 AN8703FH-V (IC101) : Frontend processor for DVD • Pin layout • Pin function Pin No. Symbol Description Pin No. Symbol Description GND3 Connect to GND LPC1 Laser input terminal (DVD) RFDIFO Non connect LPC01 O Laser drive signal output terminal (DVD)
Page 24
TH-A75 BA6664FM-X (IC251) : Motor driver • Pin layout • Block diagram DRIVER GAIN SWITCH GAIN CONTROL CURRENT SENSE AMP HALL AMP TOROUE SENSE AMP SHORT BRAKE CK Q BRAKE MODE Hall Bias 1-24 (No.22009)
Page 25
TH-A75 • Pin function Pin No. Symbol Description Non connect Output 3 for spindle motor Non connect Output 2 for spindle motor Non connect Non connect Output 1 for spindle motor Connect to ground Positive input for hall input AMP 1...
Page 27
TH-A75 4.11 BA5983FM-X (IC201) : 4-channel driver • Block diagram STAND BY Level Shift Level Shift Level Shift Level Shift STAND BY CH1/2/3 • Pin function Pin No. Symbol Description Pin No. Symbol Description VO4(-) O Inverted output of CH4...
Page 28
TH-A75 4.12 DSPC56367PV150 (IC521) : DSP • Pin layout • Block diagram MEMORY EXPANSION AREA PROGRAM HOST ESAI TRIPLE X MEMORY /INSTR. Y MEMORY (SPDIF Tx) INTER- INTER- TMER INTER- CACHE INTER-FA FACE FACE FACE 3K x 24 13K x 24...
Page 29
TH-A75 • Pin function Pin No Symbol Function SCK/SCL I/O SPI serial clock / I2C serial clock SS/HA2 SPI slave select / I2C slave address 2 HREQ I/O Host request SDO0/SDO0_1 Serial data output 0 SDO1/SDO1_1 Serial data output 1...
Page 30
TH-A75 Pin No Symbol Function FSR_1 I/O Frame sync for receiver SCKR_1 I/O Receiver serial clock_1 PINIT/NMI PLL initial / Nonmaskable interrupt Transfer acknowledge Bus request I/O Bus busy VCCC Bus control power GNDC Bus control ground Write enable Read enable...
Page 32
TH-A75 4.15 K4S643232E-TC60 (IC505) : 512K x 32 bit x 4 banks synchronous DRAM • Pin layout • Block diagram Data Input Register Bank Select LDQM 512K x 32 512K x 32 512K x 32 512K x 32 Column Decoder Latency &...
Page 33
TH-A75 • Pin function Pin No. Symbol Function Power for the input buffers and core logic. Data input/output are multiplexed on the same pin. VDDQ Isolated power supply for the output buffers to provide improved noise immunity. DQ1,DQ2 Data inputs/outputs are multiplexed on the same pins.
Page 34
TH-A75 Pin No. Symbol Function 53,54 DQ29,DQ30 Data inputs/outputs are multiplexed on the same pins. VDDQ Isolated power supply for the output buffers to provide improved noise immunity. DQ31 Data input/output are multiplexed on the same pin. This pin is recommended to be left no connection on the device.
Page 38
TH-A75 4.21 M61516FP (IC551) : Sound controller • Pin layout & Block diagram TRE R DVDD OUTPUT GAIN BASS R2 TINT CONTROL OUTPUT GAIN ZERO CROSS CONTROL DETECTOR & BASS R1 VOLGND2 TIMER DETECTOR TONE OUTPUT SELECTOR FRIN2 FLVIN FL VOL...
Page 39
TH-A75 • Pin function Pin No. Symbol Function INLH,INLI,INLJ Lch input REC L1,REC L2,REC L3,REC L4 REC output VOLGND1 Analog GND for vol. 9~12 FLIN1,SLIN1,SBLIN1,CIN1 FLch,SLch,SBLch,Cch input 13~16 SWIN1,SBRIN1,SRIN1,FRIN1 SWch,SBRch,SRch,FRch input 17,18 BASS L1,BASS L2 Tone path frequency characteristic setup...
Page 40
TH-A75 4.22 MM1561KF-X (IC593) : Regulator • Pin layout (TOP VIEW) • Block diagram Bias Cont Thermal Current Driver Reference shutdown limiter • Pin function Pin No. Symbol Function Output pin Not connect Ground Noise decrease pin CONT Control pin...
Page 41
TH-A75 4.23 MM1563DF-X (IC592) : Regulator • Pin layout (TOP VIEW) • Block diagram Bias Cont Thermal Current Driver Reference shutdown limiter • Pin function Pin No. Symbol Function Output pin Not connect Ground Noise decrease pin CONT Control pin...
Page 42
TH-A75 4.24 MN101C49GKR (IC271) : System micom • Pin layout • Pin function Pin No. Symbol Function VREF- Connect to ground NTSEL(RGB--SEL) NTSC/PAL discrimination (RGB/YC switching discrimination) signal VCR-S/C VCR S/Composite detection signal DBS-S/C DBS S/Composite detection signal TH-DET Heat sink temp. detection...
Page 43
TH-A75 Pin No. Symbol Function Not used INT/PROG Video driver filter select RELAT-CTL Speaker control BASS Bass boost control 52,53 Not used VIDEO-MUTE1 Video driver mute1 control VIDEO-MUTE2 Video driver mute2 control VIDEO-YCMIX Video driver YCMIX control VIDEO-RGB Video driver RGB control...
Page 45
TH-A75 4.27 MN102L62GLF3 (IC401) : Unit CPU • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function SWUPDN - Not connect. WAIT I Micro computer wait signal input MECHA_H/V I Disc detection O Read enable DISCSET...
Page 46
TH-A75 4.28 MN103S26EGA (IC301) : Optical disc controller • Pin layout • Pin function Pin No. Symbol Function NINT0 System control interruption 0 NINT1 System control interruption 1 VDD3 Power supply (3.3V) Ground NINT2 System control interruption 2 WAITODC System control wait control NMRST System control reset (Not connect.)
Page 47
TH-A75 Pin No. Symbol Function TILT Not connect. TILTN Not connect. Not connect. DTRD Not connect. IDGT Not connect. VDD18 Power supply (1.8V) Ground VDD3 Power supply (1.8V) OSCI1 16.9MHz clock input OSCO1 Not connect. Ground TSTSG Calibration signal VFOSHORT...
Page 48
TH-A75 Pin No. Symbol Function AS: Full adder signal RF envelope input DVD laser current control terminal Tracking drive IC input offset CD laser current control terminal TECAPA Not connect. VDD3 Power supply (3.3V) Ground 127~130 MONI0 - 3 Internal goods title monitor (Connect to TP306 - TP309)
Page 49
TH-A75 4.29 NC7S04P5-X (IC533) : Invereter • Pin layout & Block diagram • Truth table INPUT OUTPUT H : HIGH logic level L : LOW logic level 4.30 NC7ST32P5-X (IC532) : 2-Input OR Gate • Pin layout & Block diagram •...
Page 50
TH-A75 4.33 NDV8601VWA-BE (IC501) : DVD on a chip processor • Pin layout • Block diagram digital audio Video I/O port audio DAC NTSC Audio MPEG Video Audio digital audio output Video output Video SCART processor decoder processor encoder Serial...
Page 51
TH-A75 Pin No. Symbol Description 25,26 MA2,1 SDRAM Address bus terminal VDDio Power supply terminal 3.3V SDRAM Address bus terminal MA10 SDRAM Address bus terminal MA11 Non connect VSSio Connect to ground 32,33 MA12,13 SDRAM Address bus, reserved for terminal compatibility with 64Mb SDRAM Power supply terminal 1.8V...
Page 52
TH-A75 Pin No. Symbol Description VSSio Connect to ground RXD1 UART1 Serial data input from external serial device, used for IR receiver SSPIN1 I/O SSP1 Data in or 16X clock for USART function in UART1 Connect to ground SSPOUT1 I/O SSP1 Data out or UART1 data-terminal-ready signal...
Page 53
TH-A75 Pin No. Symbol Description 133,134 VI01,00 Non connect Power supply terminal 1.8V 136~139 AD31~28 I/O Multiplexed address / data bus terminal VDDio Power supply terminal 141~144 AD27~24 I/O Multiplexed address / data bus terminal PWE3 I/O Byte write enable for FLASH,EEPROM,SRAM or peripherals terminal...
Page 54
TH-A75 Pin No. Symbol Description DREQ DVD Parallel mode data request DCLK Data sampling clock DSTB Parallel mode data valid, serial mode left/right clock DVD0 DVD Drive parallel data port VSSio Connect to ground 219~223 DVD1~5 DVD Drive parallel data port VDDio Power supply terminal 3.3V...
Page 59
TH-A75 • Pin function Symbol Function A15-A8,A19 I Address inputs : To provide memory addresses. During Sector-Erase A19-A11 address lines will select the sector. During Block-Erase, A19-A15 address line will select the block. - No connection : Unconnected pins I Write Enable : To control the Write operations...
Page 61
TH-A75 4.41 STR-G6651 (IC121) : Switching regulator • Block diagram • Pin function Pin No. Symbol Description Function Drain terminal MOS FET drain Source terminal MOS FET source Ground terminal Ground Power supply terminal Input of power supply for control circuit O.C.P/F.B Over current / Feedback terminal...
Page 62
TH-A75 4.42STR-F6667B (IC101) : Switching regulator • Pin layout • Pin function Pin No Symbol Function O.C.P/F.B Over current/Feedback terminal Source terminal Drain terminal Power supply terminal Ground terminal O.V.P Overvoltage protection circuit T.S.D Thermal shutdown circuit • Block diagram START O.V.P...
Page 63
TH-A75 4.43 STR-F6668B (IC101) : Switching regulator • Pin layout • Pin function Pin No Symbol Function O.C.P/F.B Over current/Feedback terminal Source terminal Drain terminal Power supply terminal Ground terminal O.V.P Overvoltage protection circuit T.S.D Thermal shutdown circuit • Block diagram START O.V.P...
Page 64
TH-A75 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.22009) Printed in Japan 200302WPC...
TH-A75 SCHEMATIC DIAGRAMS DVD DIGITAL CINEMA SYSTEM TH-A75 CD-ROM No.SML200302 Area suffix US ---------------------- Singapore UP ---------------------------- Korea UT --------------------------- Taiwan UX ------------------- Saudi Arabia SP-XSA75 AUDI O VCR/DBS FM/AM VCR 1 VC R AUDI O ANGL E SUBTITLE DECOD E...
Page 66
TH-A75 In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "...
TH-A75 Block diagrams Overall block diagram System control section FROM/TO LVA10375-A1 Main board CN591 OF FROM/TO LVA10377-A1 TUNER UNIT (DSP) CN205 CN203 TU-R TU-R TU-L TU-L Q2801 B/E/EN/EV Q2802 IC201 8,9,10 S-MUTING version S-MUTE only RDS DECODER DRIVER CN701 TU-DTO...
Page 68
TH-A75 TH-A75 DVD servo section Video input/output section LVA10375-A1 Main board J2891 AVVLR AV COMPULINK S2401 PAL/NTSC PAL/NTSC J2402 System control IC231 J2201 VIDEO DRIVER J2401 S/COMPOSITE VIDEO IN 1 IC211 S/COMPOSITE VIDEO VIDEO OUT IC221 VIDEO S/COMPOSITE VIDEO IN 2...
Page 69
TH-A75 Audio input/output section Power supply section TO CN703 OF TO CN203 OF LVA10378-A1 Power board LVA10379-A1 LVA10375-A1 D101 LVA10377-A1 DSP board (System control) (Power amplifier) CN591 CN101 F101 CN171 TUNER_L L101 +37V AC IN L103 +37V L102 T101 +22V...
Page 70
TH-A75 TH-A75 Standard schematic diagrams System control section To Power amplifier section CN702 To DSP section CN591 To tuner unit QGF1016C2-29W QGF1205C1-06 QGF1205C1-11 CN203 CN204 CN205 NJM78M05FA IC291 D2826 D2821 TU-R C2602 R2823 TU-L D2828 C2601 Q2821 KRC102S-X R2824 EP202...
Page 88
TH-A75 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.22009SCH) 2003/02...