1. Manuals
  2. Brands
  3. Dell Manuals
  4. Laptop
  5. Venue Pro 11-7139
  6. Disassembly manual

Dell Venue Pro 11-7139 Disassembly Manual

Hide thumbs Also See for Venue Pro 11-7139:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Dell Venue Pro 11-7139
Disassembly Guide
Regulatory Model: T07G
Regulatory Type: T07G001

Advertisement

Table of Contents
loading

Related Manuals for Dell Venue Pro 11-7139

Summary of Contents for Dell Venue Pro 11-7139

  • Page 1 Dell Venue Pro 11-7139 Disassembly Guide Regulatory Model: T07G Regulatory Type: T07G001...

  • Page 3: Table Of Contents

    Contents 1 Recommended Tools......................4 2 Venue Pro 11–7139 Disassembly..................5 ............................5 Steps to remove the Back Cover .............................. 6 Steps to remove the Battery ............................8 Steps to remove the Base Cover ..........................13 Steps to remove the Coin-cell Battery ..........................14 Steps to remove the Docking Board ..........................16 Steps to remove the Fingerprint reader...

  • Page 4: Recommended Tools

    NOTE: The Venue 11 Pro–7139 does not contain any user serviceable components. All repairs need to be performed by an authorized Dell technician only. Dell is not responsible for any damage to the tablet due to unauthorized component disassembly or repairs. This document is developed to meet the EPEAT regulatory compliance...

  • Page 5: Venue Pro 11-7139 Disassembly

    Venue Pro 11–7139 Disassembly Steps to remove the Back Cover Use a scribe to pry up the recess hole on the back cover. Lift to remove the back cover. The following image shows the inside of the system after the back cover is removed.

  • Page 6: Steps To Remove The Battery

    Steps to remove the Battery NOTE: Discharge the battery as much as possible before removing from the system. This can be done by disconnecting the A/C adapter from the system (while the system is turned on) to allow the system to drain the battery. Slide the battery release latch into the unlock position.
  • Page 7 Do not apply pressure to the surface of the battery • Do not bend • Do not use tools of any kind to pry on or against the battery • If a battery cannot be removed within the constraints above, please contact Dell technical support...

  • Page 8: Steps To Remove The Base Cover

    Battery removal complete. Steps to remove the Base Cover Remove the two connector covers from the bottom case.
  • Page 9 Disconnect the docking FPC (1) and docking board cable (2) from the system board.
  • Page 12 Base removal complete.

  • Page 13: Steps To Remove The Coin-Cell Battery

    Steps to remove the Coin-cell Battery Disconnect the coin-cell battery connector from the system board. Remove the coin-cell battery.

  • Page 14: Steps To Remove The Docking Board

    Coin-cell battery removal complete. Steps to remove the Docking Board Unthread the docking board cable from the bottom case.
  • Page 15 Remove the screws securing the docking board in place. Lift to remove the docking board from the bottom case. Docking board removal complete.

  • Page 16: Steps To Remove The Fingerprint Reader

    Steps to remove the Fingerprint reader Remove the two connector covers from the bottom case. Disconnect the docking FPC (1), docking board cable (2) and fingerprint reader cable (3) from the system board.
  • Page 17 Pull up the docking FPC from the back of the LCD panel. Remove the screws from the bottom case. Use a plastic scribe to insert to the gap between the top case and bottom case, pry all edges of the tablet to release all hooks.
  • Page 18 From the back of the bottom case, peel off the cables on top of the fingerprint reader. Peel off the fingerprint reader cable from the bottom case and remove the reader. Fingerprint reader removal complete.

  • Page 19: Steps To Remove The Front Camera

    Steps to remove the Front Camera Disconnect the rear camera cable from the front camera. Lift to separate the front camera.

  • Page 20: Steps To Remove The I/O Board

    Front camera removal complete. Steps to remove the I/O Board Disconnect the HDMI FPC from the system board and tear it off from the back of the LCD panel.
  • Page 21 Remove the I/O board. I/O Board removal complete.

  • Page 22: Steps To Remove The Micro-Sim Board

    Steps to remove the micro-SIM board Press in the micro SIM card and release. Slide out the SIM card from its slot using a pair of tweezer.

  • Page 23: Steps To Remove The Power Switch Board

    micro-SIM board removal complete. Steps to remove the Power switch board Disconnect the power cable from the power switch board.
  • Page 24 Remove the screw from the power switch board. Remove the power switch board. Power switch board removal complete.

  • Page 25: Steps To Remove The Rear Camera

    Steps to remove the Rear camera Disconnect the rear camera cable from the front camera. Lift to separate the rear camera.

  • Page 26: Steps To Remove The Sd Card

    Rear camera removal complete. Steps to remove the SD card Insert an unfolded paper clip into the small hole on the micro SD card cap and release.
  • Page 27 Slide the micro SD card cap out of the system. SD card removal complete.

  • Page 28: Steps To Remove The Smartcard Reader

    Steps to remove the SmartCard reader Remove the screws securing the SmartCard reader. Lift up the SmartCard reader and flip it over.
  • Page 29 Disconnect the cables from the SmartCard reader using a pair of tweezer. Remove the SmartCard reader from the tablet. SmartCard removal complete.

  • Page 30: Steps To Remove The Speakers

    Steps to remove the Speakers Lift up the speaker from the adhesive tape on the right and unthread its cable.
  • Page 31 Remove the adhesive tapes on the speaker cables and remove the speaker module from the system. Speaker removal complete.

  • Page 32: Steps To Remove The Solid State Drive (Ssd)

    Steps to remove the Solid state drive (SSD) Remove the screw from the SSD. SSD removal complete.

  • Page 33: Steps To Remove The System Board

    Steps to remove the System Board Unthread all the antenna cables from its routing channel.
  • Page 34 Remove all the cables connected to the system board - thermal fan cable, vibration motor cable, HDMI cable, power cable, camera cable, speaker cable, USB cable and LCM FPC (on the LCD assembly). Remove the screws securing the system board. Remove the system board from the system.

  • Page 35: Steps To Remove The Thermal Fan

    System board removal complete. Steps to remove the Thermal Fan Tear off the adhesive tape.
  • Page 36 Lift up the thermal fan cable. Disconnect the thermal fan cable from the system board. Remove the screws securing the thermal fan.
  • Page 37 Remove the thermal fan from the system. Thermal fan removal complete.

  • Page 38: Steps To Remove The Usb Board

    Steps to remove the USB Board Disconnect the USB cable from the system board and tear it off from the back of LCD panel. Remove the screw securing the USB board.
  • Page 39 Remove the USB board. USB board removal complete.

  • Page 40: Steps To Remove The Wwan Card

    Steps to remove the WWAN card Disconnect the antenna cables from the WWAN card using a pair of tweezer. Remove the screw from the WWAN card.

  • Page 41: Steps To Remove The Wlan Card

    WWAN card removal complete. Steps to remove the WLAN Card Tear off the mylar tape covering the WLAN card.
  • Page 42 Disconnect the antenna cables from the WLAN card using a pair of tweezer. Remove the screw from the WLAN card. Remove the WLAN card from the system.
  • Page 43 WLAN card removal complete.

Table of Contents