Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dodge Durango 2015
Summary of Contents for Dodge Durango 2015
- Page 1 Durango 2 0 1 5 O P E R A T I N G I N F O R M A T I O N 15WD01-126-ARA-AA...
-
Page 4: Table Of Contents
Table of Contents ..............3 INTRODUCTION . -
Page 6: Introduction
INTRODUCTION • INTRODUCTION .......4 • ROLLOVER WARNING ......4 •... -
Page 7: Introduction
INTRODUCTION Operating this vehicle at excessive speeds may ROLLOVER WARNING result in loss of control, collision with other Congratulations on selecting your new Chrysler Utility vehicles have a significantly higher roll- vehicles or objects, going off the road, or over- Group LLC vehicle. -
Page 8: Important Notice
IMPORTANT NOTICE ucts without imposing any obligations upon itself to install them on products previously ALL MATERIAL CONTAINED IN THIS PUBLI- manufactured. CATION IS BASED ON THE LATEST INFOR- MATION AVAILABLE AT TIME OF PUBLICA- The Owner’s Manual illustrates and describes TION APPROVAL. -
Page 9: How To Use This Manual
the attachment or installation of such parts, it Original MOPAR® parts and accessories and HOW TO USE THIS MANUAL cannot be implicitly assumed that the driving other products approved by the manufacturer, Consult the Table of Contents to determine safety of your vehicle is unimpaired. Therefore, including qualified advice, are available at your which section contains the information you de- neither experts nor official agencies are liable. -
Page 11: Warnings And Cautions
WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ This Owners Manual contains WARNINGS ALTERATIONS against operating procedures that could result in a collision or bodily injury. It also contains WARNING! CAUTIONS against procedures that could re- sult in damage to your vehicle. If you do not Any modifications or alterations to this ve- read this entire Owners Manual, you may miss hicle could seriously affect its roadworthi-... -
Page 12: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • A WORD ABOUT YOUR KEYS ..... .12 • Keyless Ignition Node (KIN) ..... .12 •... - Page 13 • REMOTE KEYLESS ENTRY (RKE) .....17 • To Unlock The Doors And Liftgate .....18 •...
- Page 14 • Safety Checks You Should Make Inside The Vehicle ..62 • Periodic Safety Checks You Should Make Outside The Vehicle ........63...
-
Page 15: A Word About Your Keys
A WORD ABOUT YOUR KEYS NOTE: Key Fob In case the ignition switch does not change The Key Fob also contains the Remote Keyless Your vehicle uses a keyless ignition system. with the push of a button, the RKE transmit- Entry (RKE) transmitter and an emergency key, This system consists of a Key Fob with Remote ter (Key Fob) may have a low or dead bat-... -
Page 16: Ignition Or Accessory On Message
NOTE: WARNING! (Continued) With the Uconnect® system, the power win- • Allowing children to be in a vehicle unat- dow switches, radio, power sunroof (if tended is dangerous for a number of rea- equipped), and power outlets will remain sons. A child or others could be seriously active for up to 10 minutes after the ignition is placed in the OFF position. -
Page 17: Steering Wheel Lock - If Equipped
To Release The Steering Wheel Lock After placing the ignition to the ON/RUN posi- CAUTION! tion, the Vehicle Security Light will turn on for Cycle the ignition and start the engine. An unlocked car is an invitation to thieves. three seconds for a bulb check. If the light NOTE: Always remove the Key Fob from vehicle, remains on after the bulb check, it indicates that... -
Page 18: Replacement Keys
General Information CAUTION! (Continued) CAUTION! The Sentry Key® operates on a carrier fre- • The Sentry Key® Immobilizer system is • Always remove the Key Fobs from the quency of 433.92 MHz. The Sentry Key® Im- not compatible with some aftermarket re- vehicle and lock all doors when leaving the mobilizer system is subject to the following mote starting systems. -
Page 19: To Arm The System
• For vehicles not equipped with Keyless To Arm The System "Keyless Enter-N-Go™" in "Things To Know Before Starting Your Vehicle" for further Enter-N-Go™, insert a valid key into the Follow these steps to arm the Vehicle Security information). ignition switch and turn the key to the ON Alarm: position. -
Page 20: Tamper Alert
you are in the vehicle or not. If you remain in the ILLUMINATED ENTRY REMOTE KEYLESS ENTRY vehicle and open a door, the alarm will sound. If The courtesy lights will turn on when you use (RKE) this occurs, disarm the Vehicle Security Alarm. the Remote Keyless Entry (RKE) transmitter to The RKE system allows you to lock or unlock unlock the doors or open any door. -
Page 21: To Unlock The Doors And Liftgate
1st Push Of Key Fob Unlocks To Lock The Doors And Liftgate This feature lets you program the system to Press and release the LOCK button on the RKE unlock either the driver’s door or all doors on the transmitter to lock all doors and liftgate. The turn first push of the UNLOCK button on the RKE signal lights will flash to acknowledge the sig- transmitter. -
Page 22: General Information
1. Remove the emergency key by sliding the General Information mechanical latch on the back of the RKE Transmitter and receivers operate on a carrier frequency of 433.92 MHz. Operation is subject transmitter sideways with your thumb and to the following conditions: then pull the key out with your other hand. -
Page 23: Door Locks
DOOR LOCKS Power Door Locks WARNING! The power door lock switch is located on each • For personal security and safety in the front door panel. Push the switch to lock or Manual Door Locks event of an collision, lock the vehicle doors unlock the doors. -
Page 24: Child-Protection Door Lock System - Rear Doors
If a rear door is locked, it cannot be opened from To Engage Or Disengage The Child- inside the vehicle without first unlocking the Protection Door Lock System door. The door may be unlocked manually by 1. Open the rear door. raising the lock knob. -
Page 25: Keyless Enter-N-Go
KEYLESS ENTER-N-GO™ To Unlock From The Driver’s Side: NOTE: If “Unlock All Doors 1st Press” is pro- The Passive Entry system is an enhancement With a valid Passive Entry RKE transmitter grammed, all doors will unlock when you to the vehicle’s Remote Keyless Entry (RKE) within 5 ft (1.5 m) of the driver’s door handle, grab hold of the driver’s front door handle. - Page 26 Preventing Inadvertent Locking Of Passive for a power open on vehicles equipped with To Lock The Liftgate Entry RKE Transmitter In Vehicle Power Liftgate. Push the electronic liftgate With a valid Passive Entry RKE transmitter handle and lift for Manual Liftgate vehicles. To minimize the possibility of unintentionally within 3 ft (1.0 m) of the liftgate, push the locking a Passive Entry RKE transmitter inside...
-
Page 27: Windows
WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON/RUN or ACC position. - Page 28 Auto-Down Auto Up Feature With Anti-Pinch NOTE: Both the driver and front passenger window Protection — Driver And Front Passenger If the window runs into any obstacle during switches have an “Auto-Down” feature. Push Door Only Auto Up, it will reverse direction and then go the window switch past the first detent, release, Lift the window switch fully upward to the sec- back down.
-
Page 29: Wind Buffeting
Resetting The Auto Up Feature LIFTGATE Should the Auto Up feature stop working, the To Unlock/Enter The Liftgate window probably needs to be reset. To reset The liftgate passive entry unlock feature is built Auto Up: into the electronic liftgate handle. With a valid 1. -
Page 30: Power Liftgate - If Equipped
NOTE: pushing the LIFTGATE button located on left WARNING! rear trim panel, near the liftgate opening. Push- The liftgate passive entry lock button will Driving with the liftgate open can allow poi- ing the LIFTGATE button located on left rear only lock the liftgate;... - Page 31 • There are also pinch sensors attached to • If your liftgate is power closing and you WARNING! the side of the liftgate. Light pressure put the vehicle in gear, the liftgate will During power operation, personal injury or anywhere along these strips will cause continue to power close.
-
Page 32: Occupant Restraint Systems
OCCUPANT RESTRAINT 4. Never allow children to slide the shoulder belt behind them or under their arm. SYSTEMS 5. You should read the instructions provided Some of the most important safety features in your vehicle are the restraint systems: with your child restraint to make sure that you are using it properly. -
Page 33: Seat Belt Systems
Enhanced Seat Belt Use Reminder System The outboard front passenger seat BeltAlert is WARNING! (BeltAlert) not active when the outboard front passenger • Never place a rear-facing child restraint in BeltAlert is a feature intended to remind the seat is unoccupied. BeltAlert may be triggered front of an air bag. - Page 34 feature allows the shoulder part of the seat belt WARNING! (Continued) WARNING! (Continued) to move freely with you under normal condi- • It is dangerous to ride in a cargo area, • Two people should never be belted into a tions.
- Page 35 2. The seat belt latch plate is above the back of WARNING! (Continued) WARNING! (Continued) the front seat, and next to your arm in the • A seat belt that is buckled into the wrong • A shoulder belt placed behind you will not rear seat (for vehicles equipped with a rear buckle will not protect you properly.
- Page 36 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180°...
- Page 37 Adjustable Upper Shoulder Belt Anchorage NOTE: move slack from the seat belt in the event of a In the driver and front passenger seats, the top collision. These devices may improve the per- The adjustable upper shoulder belt anchor- of the shoulder belt can be adjusted upward or formance of the seat belt by removing slack age is equipped with an Easy Up feature.
- Page 38 Automatic Locking Retractor (ALR) — In Automatic Locking Mode, the shoulder belt is If Equipped automatically pre-locked. The seat belt will still The seat belts in the passenger seating posi- retract to remove any slack in the shoulder belt. tions may be equipped with a Switchable Auto- Use the Automatic Locking Mode anytime a matic Locking Retractor (ALR) which is used to child restraint is installed in a seating position...
- Page 39 How To Engage The Automatic Locking Supplemental Active Head Restraints WARNING! Mode (AHR) • The seat belt assembly must be replaced if These head restraints are passive, deployable 1. Buckle the combination lap and shoulder the switchable Automatic Locking Retrac- components, and vehicles with this equipment belt.
- Page 40 NOTE: WARNING! The Active Head Restraints (AHR) may or All occupants, including the driver, should may not deploy in the event of a front or side not operate a vehicle or sit in a vehicle’s seat impact. However, if during a front impact, a until the head restraints are placed in their secondary rear impact occurs, the AHR may proper positions in order to minimize the risk...
-
Page 41: Supplemental Restraint System (Srs)
4. The AHR front soft foam and trim half should Supplemental Restraint System lock into the back decorative plastic half. (SRS) Air Bag System Components Your vehicle may be equipped with the following air bag system components: • Occupant Restraint Controller (ORC) •... - Page 42 Advanced Front Air Bags WARNING! This vehicle has Advanced Front Air Bags for • Being too close to the steering wheel or both the driver and front passenger as a supple- instrument panel during Advanced Front ment to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in Air Bag deployment could cause serious the center of the steering wheel.
- Page 43 Advanced Front Air Bag Features Advanced Front Air Bag Operation WARNING! The Advanced Front Air Bag system has multi- Advanced Front Air Bags are designed to pro- • No objects should be placed over or near stage driver and front passenger air bags. This vide additional protection by supplementing the the air bag on the instrument panel or system provides output appropriate to the se-...
- Page 44 When the ORC detects a collision requiring the Supplemental Driver Knee Air Bag Advanced Front Air Bags, it signals the inflator This vehicle is equipped with a Supplemental units. A large quantity of non-toxic gas is gen- Driver Knee Air Bag mounted in the instrument erated to inflate the Advanced Front Air Bags.
- Page 45 Children are at an even greater risk of injury and seated properly, or if items are positioned in from a deploying air bag. the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag.
- Page 46 including children, who are up against or very WARNING! (Continued) WARNING! (Continued) close to Side Air Bags can be seriously injured • Your vehicle is equipped with SABICs. In • Being too close to the Side Air Bags during or killed. Occupants, including children, should order for the SABICs to work as intended, deployment could cause you to be se- never lean on or sleep against the door, side...
- Page 47 Side Air Bags deploy independently; a left side faster-developing event may deploy the seat you haven’t healed significantly within a few impact deploys the left Side Air Bags only and a belt pretensioners as well as the SABs and days, or if you have any blistering, see your right side impact deploys the right Side Air Bags SABICs on both sides of the vehicle.
- Page 48 • Turn on the interior lights, which remain on as The ORC contains a backup power supply WARNING! (Continued) long as the battery has power or until the system that may deploy the air bags even if the and the seat belt retractor assemblies re- ignition is placed in the “OFF”...
- Page 49 • The Air Bag Warning Light remains on after Maintaining Your Air Bag System WARNING! (Continued) the four to eight-second interval. • Do not attempt to modify any part of your • The Air Bag Warning Light comes on inter- WARNING! air bag system.
-
Page 50: Child Restraints
Event Data Recorder (EDR) NOTE: WARNING! This vehicle is equipped with an event data EDR data are recorded by your vehicle only if In a collision, an unrestrained child can be- recorder (EDR). The main purpose of an EDR is a non-trivial crash situation occurs;... - Page 51 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger Either an Infant Carrier or a Convertible Child Infants and Toddlers and who have not reached the height or Restraint, facing rearward in the rear seat of weight limits of their child restraint the vehicle...
- Page 52 Infants And Child Restraints All children whose weight or height is above the WARNING! Safety experts recommend that children ride forward-facing limit for the child seat should use • Never place a rear-facing child restraint in rear-facing in the vehicle until they are two a belt-positioning booster seat until the vehicle’s front of an air bag.
- Page 53 Children Too Large For Booster Seats If the answer to any of these questions was WARNING! (Continued) Children who are large enough to wear the “no,” then the child still needs to use a booster • After a child restraint is installed in the shoulder belt comfortably, and whose legs are seat in this vehicle.
- Page 54 Recommendations For Attaching Child Restraints Restraint Type Combined Weight Use any attachment method shown with an “X” Below of the Child + Child LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Restraint Anchors Only Anchors + Top Tether Anchor Tether Anchor Rear-Facing Child...
- Page 55 Lower Anchors And Tethers For Children these seating positions, the seat belt must be (LATCH) Restraint System used with the top tether anchorage to install the child restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle Captains Chairs Second Row (6 Passenger) Lower Anchorage Symbol 2 anchorages per...
- Page 56 What is the weight limit (child’s weight + weight of the 65 lbs (29.5 kg) Use the LATCH anchorage system until the combined child restraint) for using the LATCH anchorage system to weight of the child and the child restraint is 65 lbs attach the child restraint? (29.5 kg).
- Page 57 Locating LATCH Anchorages Locating Tether Anchorages — 2nd Row There are tether strap anchorages The lower anchorages are round behind each rear seating position bars that are found at the rear of located on the back of the seat. the seat cushion where it meets the seatback.
- Page 58 LATCH-compatible child restraint systems will WARNING! (Continued) be equipped with a rigid bar or a flexible strap • Never use the same lower anchorage to on each side. Each will have a hook or connec- attach more than one child restraint. tor to attach to the lower anchorage and a way to tighten the connection to the anchorage.
- Page 59 1. Loosen the adjusters on the lower straps 5. Tighten all of the straps as you push the child and on the tether strap of the child seat so restraint rearward and downward into the seat. that you can more easily attach the hooks or Remove slack in the straps according to the connectors to the vehicle anchorages.
- Page 60 the webbing retract back into the retractor. If it is WARNING! locked, the ALR will make a clicking noise while • Improper installation of a child restraint to the webbing is pulled back into the retractor. the LATCH anchorages can lead to failure For additional information on ALR, refer to the of the restraint.
- Page 61 What is the weight limit (child’s weight + weight Always use the tether anchor when using the of the child restraint) for using the Tether seat belt to install a forward facing child Weight limit of the Child Restraint Anchor with the seat belt to attach a forward restraint, up to the recommended weight limit facing child restraint? of the child restraint.
- Page 62 6. Try to pull the webbing out of the retractor. If Installing Child Restraints Using the Top Tether Anchorage it is locked, you should not be able to pull out any webbing. If the retractor is not locked, repeat step 5. 1.
- Page 63 3. Route the tether strap to provide the most 6. Remove slack in the tether strap according to direct path for the strap between the anchor the child restraint manufacturer’s instructions. and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise WARNING! the head restraint, and where possible, route...
-
Page 64: Transporting Pets
Transporting Pets The engine oil installed in the engine at the SAFETY TIPS factory is a high-quality energy conserving type Air Bags deploying in the front seat could harm lubricant. Oil changes should be consistent with your pet. An unrestrained pet will be thrown Transporting Passengers anticipated climate conditions under which ve- about and possibly injured, or injure a passen-... -
Page 65: Exhaust Gas
Exhaust Gas The best protection against carbon monoxide Front seat belt assemblies must be replaced entry into the vehicle body is a properly main- after a collision. Rear seat belt assemblies must tained engine exhaust system. be replaced after a collision if they have been WARNING! damaged (i.e., bent retractor, torn webbing, Whenever a change is noticed in the sound of... - Page 66 Floor Mat Safety Information Periodic Safety Checks You Should WARNING! (Continued) Always use floor mats designed to fit the foot- Make Outside The Vehicle • Never put floor mats or other floor cover- well of your vehicle. Use only floor mats that Tires ings on top of already installed floor mats.
-
Page 68: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • MIRRORS ........71 •... - Page 69 • Passenger’s Power Seat — If Equipped ....80 • Power Lumbar — If Equipped ..... . .81 •...
- Page 70 • Interior Lights .......98 • Lights-On Reminder ......98 •...
- Page 71 • To Accelerate For Passing ......107 • ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED ..107 •...
- Page 72 • ParkSense® Display ......125 • Enabling And Disabling ParkSense® ....127 •...
- Page 73 • Door Storage....... . .140 • Front Center Console......141 •...
-
Page 74: Inside Day/Night Mirror — If Equipped
MIRRORS NOTE: • The Automatic Dimming Mirror feature is Inside Day/Night Mirror — disabled when the vehicle is in reverse If Equipped gear to improve rear view viewing. A single ball joint mirror is provided in the • The Automatic Dimming Mirror feature can vehicle. -
Page 75: Outside Mirrors Folding Feature
Outside Mirrors Folding Feature Press the switch once and the mirrors will fold CAUTION! in, pressing the switch a second time will return All outside mirrors are hinged and may be To avoid damage to the mirror during clean- the mirrors to the normal driving position. moved either forward or rearward to resist dam- ing, never spray any cleaning solution di- age. - Page 76 Heated Mirrors — If Equipped NOTE: The Tilt Mirrors in Reverse feature is not These mirrors are heated to melt frost turned on when delivered from the factory. or ice. This feature can be activated The Tilt Mirrors in Reverse feature can be whenever you turn on the rear window turned on and off using the Uconnect®...
-
Page 77: Sun Visor Extension — If Equipped
vehicle speed has reached approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones. •... - Page 78 the area of the rear fascia where the radar Entering From The Side sensors are located with foreign objects (bum- Vehicles that move into your adjacent lanes per stickers, bicycle racks, etc.). from either side of the vehicle. BSM Warning Light The BSM system monitors the detection zone from three different entry points (Side, Rear, Sensor Location (Driver Side Shown)
- Page 79 Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle If you pass another vehicle slowly (with a rela- on either side and enter the rear detection zone tive speed of less than 15 mph (24 km/h) and with a relative speed of less than 30 mph the vehicle remains in the blind spot for approxi- (48 km/h).
-
Page 80: Rear Cross Path (Rcp)
Rear Cross Path (RCP) The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. -
Page 81: Modes Of Operation
objects moving a maximum of approximately Blind Spot Alert Lights/Chime WARNING! (Continued) 20 mph (32 km/h), such as in parking lot situa- When operating in Blind Spot Alert Lights/ mals, other vehicles, obstructions, and blind tions. Chime mode, the BSM system will provide a spots before backing up. -
Page 82: Power Seats — If Equipped
is reduced. Turn/hazard signal status is ignored; WARNING! (Continued) the RCP state always requests the chime. • Do not allow people to ride in any area of Blind Spot Alert Off your vehicle that is not equipped with seats When the BSM system is turned off there will be and seat belts. -
Page 83: Passenger's Power Seat - If Equipped
Adjusting The Seat Up Or Down Passenger’s Power Seat — WARNING! The height of the seats can be adjusted up or If Equipped • Adjusting a seat while driving may be dan- down. Pull upward or push downward on the Some models are equipped with a six-way gerous. -
Page 84: Power Lumbar - If Equipped
Power Lumbar — If Equipped Manual Front Passenger Seat WARNING! Vehicles equipped with power driver or passen- Forward/Rearward Adjustment • Adjusting a seat while driving may be ger seats may also be equipped with power Some models may be equipped with a manual dangerous. -
Page 85: Front Passenger Seat Fold-Flat Feature - If Equipped
Front Passenger Seat Fold-Flat Heated Seats — If Equipped Feature — If Equipped On some models, the front and rear seats may be equipped with heaters located in the seat To fold the seatback to the flat load-floor posi- cushions and seat backs. tion, lift the recline lever and push the seatback forward. - Page 86 Front Heated Seats NOTE: The front heated seats control buttons are lo- • Once a heat setting is selected, heat will cated within the climate or controls screen of the be felt within two to five minutes. touchscreen. • The engine must be running for the You can choose from HI, LO or OFF heat heated seats to operate.
-
Page 87: Front Ventilated Seats - If Equipped
When the HIGH-level setting is selected, the The front ventilated seats control buttons are WARNING! (Continued) heater will provide a boosted heat level during located within the Uconnect® system. You can • Do not place anything on the seat or the first four minutes of operation. - Page 88 front passenger in certain types of rear impacts. Push rearward on the bottom of the head re- WARNING! Refer to “Occupant Restraints” in “Things To straint to move the head restraint away from The head restraints for all occupants must be Know Before Starting Your Vehicle”...
- Page 89 Head Restraints — Rear Seats WARNING! The head restraints on the outboard seats are • Do not place items over the top of the not adjustable. They automatically fold forward Active Head Restraint, such as coats, seat when the rear seat is folded to a load floor covers or portable DVD players.
-
Page 90: 60/40 Split Rear Seat
NOTE: WARNING! • The head restraints can only be folded Sitting in a seat with the head restraint in its downward using the Headrest button. The lowered position could result in serious injury head restraints must be raised manually or death in a collision. Always make sure the when occupying the third row. -
Page 91: Rear Captain Chairs - If Equipped
To Raise Rear Seat Tumbled the seat rearward and lock it into place. WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. - Page 92 Easy Access For Third Row Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1. Pull upward on the release lever to release the seat. Release Lever Tumble Strap WARNING! Do not drive the vehicle with the second row seats in the tumbled position.
-
Page 93: Folding Third Row
Folding Third Row Both third row seats can be folded forward to increase the cargo area. To lower either seat pull on the release handle located on back of the seat and lower the seat using the pull strap located next to the release handle. Mini Console Stepping Pad Third Row Folded To Raise Rear Seat... -
Page 94: Driver Memory Seat - If Equipped
NOTE: Programming The Memory Feature WARNING! (Continued) Your vehicle is equipped with two RKE trans- NOTE: securely locked into position the seat will not mitters, one RKE transmitter can be linked to To create a new memory profile, perform the provide the proper stability for child seats memory position 1 and the other transmitter following:... -
Page 95: Linking And Unlinking The Remote Keyless Entry Transmitter To Memory
Vehicles Not Equipped With Keyless “Customer-Programmable Features — NOTE: Uconnect® Access 8.4 Settings ” in “Un- Enter-N-Go™ If a memory profile has not already been set, derstanding Your Instrument Panel” for refer to Programming The Memory Feature 1. Insert the ignition key fob, and turn the further information. -
Page 96: Memory Position Recall
• When you remove the Key Fob from the Memory Position Recall A recall can be cancelled by pressing any of the MEMORY buttons during a recall (S, 1, or 2). ignition (or change the ignition to OFF, for NOTE: When a recall is cancelled, the driver’s seat, vehicles equipped with Keyless Enter-N- The vehicle must be in PARK to recall... -
Page 97: To Open And Close The Hood
NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the fac- tory. The Easy Entry/Exit feature is enabled (or later disabled) through the program- mable features in the Uconnect® system. Refer to “Uconnect® Settings/Customer Programmable Features” in “Understanding Your Instrument Panel”... -
Page 98: Lights
Plastic is not as scratch resistant as glass WARNING! and therefore different lens cleaning pro- Be sure the hood is fully latched before cedures must be followed. driving your vehicle. If the hood is not fully • To minimize the possibility of scratching latched, it could open when the vehicle is in the lenses and reducing light output, motion and block your vision. -
Page 99: Headlights On Automatically With Wipers
• To opt out of the Advanced Auto High- NOTE: Automatic High Beam — If Equipped Beam Sensitivity Control (default) and en- The engine must be running before the The automatic high beam system provides in- ter Reduced High-Beam Sensitivity Con- creased forward lighting at night by automating headlights will come on in the automatic trol (not recommended), toggle highbeam... -
Page 100: Daytime Running Lights - If Equipped
To Deactivate Headlight Delay Parking Lights And Panel Lights To aid in your exit, your vehicle is equipped with 1. Pull the multifunction lever toward you (or a headlight delay that will leave the headlights To turn on the parking lights and instru- rearward in car) to manually deactivate the on for approximately up to 90 seconds. -
Page 101: Lights-On Reminder
The fog lights will operate only when the parking The brightness of the instrument panel lighting Lights-On Reminder lights are on or when the vehicle headlights are can be regulated by rotating the dimmer control If the headlights, parking lights, or cargo lights on low beam. - Page 102 Front Map/Reading Lights Each light can be turned on by pressing a switch Courtesy Lights on either side of the console. These buttons are The front map/reading lights are mounted in the The courtesy lights can be turned on by press- backlit for night time visibility.
-
Page 103: Ambient Light
Ambient Light Turn Signals Lane Change Assist The overhead console is equipped with an Move the multifunction lever up or down and the Tap the lever up or down once, without moving ambient light feature. This light casts illumina- arrows on each side of the instrument cluster beyond the detent, and the turn signal (right or tion for improved visibility of the floor and center flash to show proper operation of the front and... -
Page 104: Windshield Wipers And Washers
WINDSHIELD WIPERS AND Windshield Wiper Operation CAUTION! (Continued) Rotate the end of the lever to one of the first four WASHERS blades cannot return to the “park” position, detent positions for intermittent settings, the fifth The windshield wiper/washer controls are lo- damage to the wiper motor may occur. -
Page 105: Windshield Washer Operation
NOTE: If the end of the lever is pushed while the wipers NOTE: are in the off position, the wipers will operate for If the vehicle is moving less than 10 mph The mist feature does not activate the several wipe cycles, then turn off. (16 km/h), delay times will be doubled. -
Page 106: Rain Sensing Wipers — If Equipped
• Use of Rain-X® or products containing Rain Sensing Wipers — If Equipped TILT/TELESCOPING STEERING wax or silicone may reduce Rain Sensing This feature senses moisture on the windshield COLUMN performance. and automatically activates the wipers for the This feature allows you to tilt the steering col- driver. -
Page 107: Heated Steering Wheel — If Equipped
steering column in position, push the lever WARNING! upward until fully engaged. Do not adjust the steering column while driving. Adjusting the steering column while WARNING! driving or driving with the steering column Do not adjust the steering column while unlocked, could cause the driver to lose driving. -
Page 108: Electronic Speed Control — If Equipped
• Press the heated steering wheel button ELECTRONIC SPEED NOTE: once to turn the heating element ON. In order to ensure proper operation, the CONTROL — IF EQUIPPED • Press the heated steering wheel button Electronic Speed Control System has been When engaged, the Electronic Speed Control designed to shut down if multiple Speed second time to turn the heating element OFF. -
Page 109: To Deactivate
To Deactivate increment shown is dependant on the chosen WARNING! speed unit of U.S. (mph) or Metric (km/h): A soft tap on the brake pedal, pushing the Leaving the Electronic Speed Control sys- CANCEL button, or normal brake pressure U.S. Speed (mph) tem on when not in use is dangerous. -
Page 110: To Accelerate For Passing
• If the button is continually pressed, the set To Decrease Speed WARNING! (Continued) speed will continue to decrease until the When the Electronic Speed Control is set, you speed. Your vehicle could go too fast for the button is released, then the new set speed can decrease speed by pushing the SET - button. - Page 111 NOTE: You can change the mode by using the Cruise WARNING! (Continued) Control buttons. The two control modes function • If the sensor does not detect a vehicle • The ACC system: differently. Always confirm which mode is se- ahead of you, ACC will maintain a fixed •...
-
Page 112: Adaptive Cruise Control (Acc) Operation
WARNING! (Continued) WARNING! (Continued) • Will bring the vehicle to a complete stop • When circumstances do not allow safe while following a target vehicle and hold driving at a constant speed. the vehicle for 2 seconds in the stop position. -
Page 113: Activating Adaptive Cruise Control (Acc)
• When the automatic transmission is in NOTE: To turn the system OFF, push and release the PARK, REVERSE or NEUTRAL. Adaptive Cruise Control (ACC) ON/OFF button Any chassis/suspension or tire size modifi- again. At this time, the system will turn off and cations to the vehicle will effect the perfor- •... -
Page 114: To Set A Desired Acc Speed
• The Normal (Fixed Speed) Electronic Speed To Set A Desired ACC Speed To Cancel Control ON/OFF button is pressed. When the vehicle reaches the speed desired, The following conditions cancel the system: push the SET + button or the SET - button and •... -
Page 115: To Vary The Speed Setting
for more information. The speed increment shown To Decrease Speed WARNING! is dependant on the chosen speed unit of U.S. While ACC is set, the set speed can be de- The Resume function should only be used if (mph) or Metric (km/h): creased by pressing the SET - button. -
Page 116: Setting The Following Distance In Acc
Metric Speed (km/h) vehicle will release the vehicle brakes two seconds after coming to a full stop. • Pressing the SET - button once will result in • The ACC system maintains set speed a 1 km/h decrease in set speed. Each sub- when driving up hill and down hill. - Page 117 lease. Each time the button is pressed, the The maximum braking applied by ACC is lim- distance setting increases by one bar (longer). ited; however, the driver can always apply the brakes manually, if necessary. To decrease the distance setting, press the Distance Setting —...
-
Page 118: Overtake Aid
NOTE: the left side until it determines that the vehicle WARNING! has moved back to a location with left hand The “Brake!” Screen in the DID is a warning When the ACC system is resumed, the driver drive traffic. for the driver to take action and does not must ensure that there are no pedestrians, necessarily mean that the Forward Collision ACC Operation At Stop... -
Page 119: Display Warnings And Maintenance
Adaptive Cruise Control Ready Display Warnings And Maintenance NOTE: If the “ACC/FCW Unavailable Wipe Front When ACC is activated but the vehicle speed “Wipe Front Radar Sensor In Front Of Radar Sensor” warning is active Normal setting has not been selected, the display will Vehicle”... - Page 120 • If the sensor or front end of the vehicle is “Clean Front Windshield” Warning When the condition that created limited func- damaged due to a collision, see your autho- The “ACC/FCW Limited Functionality Clean tionality is no longer present, the system will rized dealer for service.
-
Page 121: Precautions While Driving With Acc
Precautions While Driving With ACC NOTE: In certain driving situations, ACC may have On tight turns ACC performance may be detection issues. In these cases, ACC may limited. brake late or unexpectedly. The driver needs to stay alert and may need to intervene. Towing A Trailer Towing a trailer is not advised when using ACC. - Page 122 Using ACC On Hills Lane Changing Narrow Vehicles When driving on hills, ACC may not detect a ACC may not detect a vehicle until it is com- Some narrow vehicles traveling near the outer vehicle in your lane. Depending on the speed, pletely in the lane in which you are traveling.
-
Page 123: Normal (Fixed Speed) Electronic Speed Control Mode
Stationary Objects And Vehicles Normal (Fixed Speed) Electronic WARNING! ACC does not react to stationary objects and Speed Control Mode In the normal Cruise Control mode, the sys- stationary vehicles. For example, ACC will not In addition to Adaptive Cruise Control mode, a tem will not react to vehicles ahead. - Page 124 To Vary The Speed Setting Metric Speed (km/h) decrement shown is dependant on the speed of To Increase Speed U.S. (mph) or Metric (km/h) units: • Pressing the SET + button once will result in When the Normal (Fixed Speed) Electronic U.S.
-
Page 125: Forward Collision Warning (Fcw) With Mitigation - If Equipped
To Cancel To Turn Off NOTE: The following conditions will cancel the Normal The system will turn off and erase the set speed FCW monitors the information from the for- (Fixed Speed) Electronic Speed Control without in memory if: ward looking sensors as well as the Elec- clearing the memory: •... -
Page 126: Turning Fcw On Or Off
• It is unsafe to test the FCW system. To Turning FCW ON Or OFF prevent such misuse of the system, after NOTE: four Active Braking events within an igni- The default status of FCW is “On”, this tion cycle, the Active Braking portion of allows the system to warn you of a possible FCW will be deactivated until the next collision with the vehicle in front of you. -
Page 127: Changing Fcw And Active Braking Status
NOTE: Changing the FCW status to the “Near” setting, FCW Limited Warning allows the system to warn you of a possible The FCW system state is kept in memory If the DID displays “ACC/FCW Limited Func- collision with the vehicle in front of you when tionality”... -
Page 128: Parksense® Rear Park Assist - If Equipped
PARKSENSE® REAR PARK ParkSense® Sensors ParkSense® Display The four ParkSense® sensors, located in the When the vehicle is in REVERSE, the DID will ASSIST — IF EQUIPPED rear fascia/bumper, monitor the area behind the display the park assist ready system status. The ParkSense®... - Page 129 arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous. Slow Tone Continuous Tone The vehicle is close to the obstacle when the warning display shows one flashing arc and Single 1/2 Second Tone sounds a continuous tone.
-
Page 130: Enabling And Disabling Parksense
WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous Chime Second Tone None 4th Solid Solid... - Page 131 • When you turn ParkSense® OFF, the in- Service The ParkSense® Rear Park struction and then cycle the ignition. If the message continues to appear, see an autho- strument cluster will display Assist System rized dealer. “PARKSENSE OFF” Furthermore, once During vehicle start up, when the ParkSense®...
- Page 132 • Use the ParkSense® switch to turn the CAUTION! (Continued) WARNING! (Continued) ParkSense® system OFF if objects such • The vehicle must be driven slowly when • Before using ParkSense®, it is strongly as bicycle carriers, trailer hitches, etc. are using ParkSense®...
-
Page 133: Parkview® Rear Back Up Camera — If Equipped
PARKVIEW® REAR BACK UP When the vehicle is shifted out of REVERSE and its projected backup path based on the (with camera delay turned ON), the rear view steering wheel position. A dashed center line CAMERA — IF EQUIPPED image with dynamic grid lines will be displayed overlay indicates the center of the vehicle to Your vehicle may be equipped with the for up to 10 seconds after shifting out of "RE-... -
Page 134: Overhead Console
OVERHEAD CONSOLE WARNING! CAUTION! (Continued) The overhead console contains courtesy/ • To avoid vehicle damage, the vehicle must Drivers must be careful when backing up reading lights and storage for sunglasses. even when using the ParkView® Rear Back be driven slowly when using ParkView® to Power sunroof switches may also be included, if Up Camera. - Page 135 Front Map/Reading Lights Each light can be turned on by pressing a switch Courtesy Lights on either side of the console. These buttons are The front map/reading lights are mounted in the The courtesy lights can be turned on by press- backlit for night time visibility.
-
Page 136: Power Sunroof — If Equipped
Sunglasses Bin Door POWER SUNROOF — WARNING! At the front of the console a compartment is IF EQUIPPED • Never leave children unattended in a ve- provided for the storage of a pair of sunglasses. The power sunroof switch is located between hicle, or with access to an unlocked ve- The storage compartment access is a “push/ the sun visors on the overhead console. -
Page 137: Closing Sunroof — Express
Closing Sunroof — Express NOTE: WARNING! (Continued) Press the switch forward and release it within If three consecutive sunroof close attempts • Do not allow small children to operate the one-half second and the sunroof will close result in Pinch Protect reversals, the fourth sunroof. -
Page 138: Electrical Power Outlets
Wind Buffeting NOTE: NOTE: Wind buffeting can be described as the percep- Ignition Off time is programmable through the • All accessories connected to the “bat- tion of pressure on the ears or a helicopter-type Uconnect® System. Refer to “Uconnect® tery”... - Page 139 The front power outlet is located inside the In addition to the front power outlet, there is also If your vehicle is equipped with a rear full center storage area on the center stack of the instru- a power outlet located in the storage area of the console, there is also a power outlet located in ment panel.
- Page 140 The rear cargo power outlet is located in the NOTE: right rear cargo area. The rear cargo power outlet can be changed to “battery” powered all the time by switch- ing the power outlet right rear quarter panel fuse in the fuse panel from fuse location F90 to F91.
-
Page 141: Front Seat Cupholders
CUPHOLDERS WARNING! CAUTION! (Continued) • Accessories that draw higher power (i.e., To avoid serious injury or death: Front Seat Cupholders • Only devices designed for use in this type coolers, vacuum cleaners, lights, etc.) will There are two cupholders for the front seat of outlet should be inserted into any 12 Volt degrade the battery even more quickly. -
Page 142: Rear Cupholders
Rear Cupholders Rear Full Console Cupholders — The rear full console cupholders are equipped If Equipped with a light ring that illuminates the cupholders Rear Center Arm Rest Cupholders — for the rear passengers. The light ring is con- There are two cupholders for the rear seat If Equipped trolled by the Dimmer Control. -
Page 143: Door Storage
Rear Mini Console Cupholders — STORAGE Door Storage If Equipped Large storage areas are built into the door panels for easy access. Glove Compartment There are two cupholders for the rear seat The glove compartment is located on the right passengers located in the front of the rear mini side of the instrument panel. -
Page 144: Front Center Console
Front Center Console Rear Full Center Console — To open the upper storage compartment, pull upward on the small latch located on the front of The front center console contains both an upper If Equipped the lid. and a lower storage area. The rear full center console contains both an upper and a lower storage area. - Page 145 Lift upward on the larger of the latches to When lifted forward there is access to the lower CAUTION! access the lower storage compartment. storage compartment. Remove any items stored in the console NOTE: cupholders or devices with cords routing Lower storage compartment light is always through upper storage area.
-
Page 146: Rear Mini Center Console - If Equipped
NOTE: Open storage areas, or cubby bins with remov- Rear Mini Center Console — able liners, are located rearward of the cuphold- When the lower storage compartment is If Equipped ers and in the lower front of the console. accessed it allows the armrest to flip for- An open storage area, or cubby bin with remov- ward for “fold flat mode”. -
Page 147: Cargo Area Features
CARGO AREA FEATURES To operate the flashlight, press the switch once Cargo Storage for high, twice for low, and a third time to return There is a removable storage bin located on the to off. left side of the rear cargo area. Rechargeable Flashlight The rechargeable flashlight is mounted on the Additional storage can be found in the load... -
Page 148: Retractable Cargo Area Cover - If Equipped
Retractable Cargo Area Cover — WARNING! (Continued) WARNING! If Equipped • To help protect against personal injury, cargo floor or in the passenger compartment. NOTE: Remove the cover from the vehicle when passengers should not be seated in the The purpose of this cover is for privacy, not taken from its mounting. -
Page 149: Rear Window Features
Once the switch is released it will return to the WARNING! (Continued) OFF position and the wipers will cycle several • Always place cargo evenly on the cargo times before returning to the parked position. floor. Put heavier objects as low and as far NOTE: forward as possible. -
Page 150: Roof Luggage Rack - If Equipped
NOTE: ROOF LUGGAGE RACK — To prevent excessive battery drain, use the IF EQUIPPED rear window defroster only when the engine The crossbars and side rails are designed to is operating. carry weight on vehicles equipped with a lug- gage rack. The load must not exceed 150 lbs CAUTION! (68 kg), and should be uniformly distributed over the luggage rack crossbars. -
Page 151: Deploying The Crossbars
Deploying the Crossbars Remove the crossbar from the stowed position Starting with one crossbar, bend down the pivot by sliding the crossbar towards the center of the supports at each end. Starting with one crossbar, completely loosen roof. Repeat with crossbar on the opposite side. the thumb screws at both ends of the crossbar. -
Page 152: Stowing The Crossbars
Position the crossbars across the roof making Stowing The Crossbars sure the letters on the crossbars align with the Starting with one crossbar, completely loosen matching letters on the side rail. the thumb screws at both ends. Slide the cross- bar away from the matching letter to remove it from the deployed position. - Page 153 Then, position the crossbar along the correct Repeat the procedure to stow the second cross- side rail. Make sure the letters on the crossbar bar on the opposite side. align with the matching letters on the side rail. Crossbar To Side Rail Once the driver’s side crossbar is in place, Stowed Crossbars tighten the thumb screws completely.
- Page 154 WARNING! CAUTION! (Continued) CAUTION! (Continued) • To avoid damage to the roof rack and • Travel at reduced speeds and turn corners Cargo must be securely tied before driving your vehicle. Improperly secured loads can vehicle, do not exceed the maximum roof carefully when carrying large or heavy fly off the vehicle, particularly at high speeds, rack load capacity of 150 lb (68 kg).
-
Page 156: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL • INSTRUMENT PANEL FEATURES ....156 • INSTRUMENT CLUSTER ......157 •... - Page 157 • Customer Programmable Features — Uconnect® 8.4 Settings . . .181 • Uconnect® RADIOS — IF EQUIPPED ....192 • iPod®/USB/MP3 CONTROL — IF EQUIPPED ....192 •...
- Page 158 • Climate Control Functions..... . .210 • Automatic Temperature Control (ATC) ....211 •...
-
Page 159: Instrument Panel Features
INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Lower Switch Bank 2 — Instrument Cluster 7 — Hazard Switch 3 — Radio 8 — Ignition Start/Stop Button 4 — Glove Compartment 9 — Dimmer Switch 5 — Climate Controls 10 —... -
Page 160: Instrument Cluster
INSTRUMENT CLUSTER... -
Page 161: Instrument Cluster Descriptions
INSTRUMENT CLUSTER turned to the ON/RUN position and may stay on 6. Selectable DID Information for as long as four seconds. DESCRIPTIONS This area of the cluster will display selectable If the ABS light remains on or turns on while information such as compass, outside tempera- 1. - Page 162 9. Selectable DID Information 11. Electronic Park Brake Failure Indicator CAUTION! — If Equipped This area of the cluster will display selectable Prolonged driving with the Malfunction Indi- information such as compass, outside tempera- This light indicates the Electronic cator Light (MIL) on could cause damage to ture, etc.
- Page 163 13. Brake Warning Light Brake Warning Light, which will turn on when CAUTION! (Continued) the brake fluid level in the master cylinder has This light monitors various brake func- ture gauge reads “H” pull over and stop the dropped below a specified level. tions, including brake fluid level and vehicle.
- Page 164 Vehicles equipped with the Anti-Lock Brake 14. Fuel Gauge/Fuel Door Reminder the low tire pressure telltale illuminates, you System (ABS), are also equipped with Elec- should stop and check your tires as soon as The fuel pump symbol points to the tronic Brake Force Distribution (EBD).
- Page 165 able to detect or signal low tire pressure as 18. Air Bag Warning Light CAUTION! (Continued) intended. TPMS malfunctions may occur for a This light will turn on for four to able. After using an aftermarket tire sealant it variety of reasons, including the installation of eight seconds as a bulb check is recommended that you take your vehicle replacement or alternate tires or wheels on the...
- Page 166 20. Electronic Stability Control (ESC) OFF NOTE: 23. Rear Fog Light Indicator Indicator Light — If Equipped • The “ESC Off Indicator Light” and the This indicator will illuminate when the “ESC Activation/Malfunction Indicator rear fog lights are on. (Refer to “Lights” This light indicates the Electronic Light”...
-
Page 167: Driver Information Display (Did)
• Audio • DOWN Arrow Button DRIVER INFORMATION • Stored Messages DISPLAY (DID) Push and release the DOWN but- ton to scroll downward through the • Screen Setup The Driver Information Display (DID) features a main menu. driver-interactive display that is located in the The system allows the driver to select informa- instrument cluster. -
Page 168: Did Displays
• Unstored Messages Until RUN DID Displays The main display area will normally display the main menu or the screens of a selected feature The DID displays are located in the center portion These messages deal primarily with the Re- of the main menu. -
Page 169: Did Messages
• Service Tire Pressure System ON/RUN position. To turn off the message DID Messages temporarily, push and release the OK button. To • Speed Warning Set • Front Seatbelts Unbuckled reset the oil change indicator system (after • Speed Warning Exceeded •... -
Page 170: Did White Telltales
• Doors Open • Windshield Washer Fluid Low Indicator The Reconfigurable Telltales section is divided into the white telltales area on the right, amber • Liftgate Open This telltale will turn on to indicate telltales in the middle, and red telltales on the the windshield washer fluid is low. -
Page 171: Did Red Telltales
refer to “Adaptive Cruise Control (ACC)” in driving, stop the vehicle and shut off the engine If jump starting is required, refer to “Jump “Understanding The Features Of Your Vehicle.” as soon as possible. A chime will sound when Starting Procedures” in “What To Do In this light turns on. -
Page 172: Did Green Telltales
• Engine Temperature Warning Light • Electric Power Steering Malfunction – DID Selectable Menu Items If Equipped Push and release the UP or DOWN arrow This light warns of an overheated en- buttons until the desired Selectable Menu icon/ gine condition. As temperatures rise This telltale is on when the Electric title is highlighted in the DID. - Page 173 • If the Tire Pressure system requires service, Vehicle Info Driver Assist — If Equipped “Service Tire Pressure System” is displayed. Push and release the UP or DOWN Push and release the UP or DOWN arrow button until the Vehicle Info arrow button until the Driver Assist Tire PSI is an information only function and icon/title is highlighted in the DID.
-
Page 174: Screen Setup Driver Selectable Items
Trip Stored Messages Screen Setup Driver Selectable Push and release the UP or DOWN Items arrow button until the Messages Push and release the UP or DOWN Current Gear Menu icon/title is highlighted in the arrow button until the Trip icon/title •... -
Page 175: Uconnect® Settings
• Time CAUTION! • Range To Empty (RTE) Do not attach any object to touchscreen, • Fuel Economy Average doing so can result in damage to the touch- screen. • Fuel Economy Current • Trip A • Trip B Restore To Defaults (Restores All Settings To Default Settings) Uconnect®... -
Page 176: Buttons On The Touchscreen
Your Uconnect® system may also have Screen NOTE: status, press and release the “Auto” or “Manual” Off and Back buttons located below the button on the touchscreen. Then press the Only one touchscreen area may be selected Uconnect® system. arrow back button on the touchscreen. at a time. - Page 177 • Display Brightness With Headlights OFF • Units back arrow button on the touchscreen to return to the previous menu, or push the back button When in this display, you may select the overall When in this display, you may select to have the on the faceplate.
- Page 178 Clock & Date Safety/Assistance position. The mirrors will move back to their After pressing the “Clock” button on the touch- After pressing the “Safety/Assistance” button on previous position when the transmission is screen the following settings will be available: the touchscreen the following settings will be shifted out of REVERSE.
- Page 179 • ParkView® Backup Camera Delay Press the back arrow button on the touchscreen Press the back arrow button on the touchscreen to return to the previous menu. to return to the previous menu. When the vehicle is shifted out of REVERSE •...
- Page 180 • Auto Dim High Beams — If Equipped • Sound Horn With Lock with the Remote Keyless Entry (RKE) transmit- ter. This feature may be selected with or without When this feature is selected, the high beam When this feature is selected, the horn will the sound horn on lock feature selected.
- Page 181 • Power Lift Gate Alert — If Equipped NOTE: the touchscreen to return to the previous menu. Refer to “Keyless Enter-N-Go™” in “Things To If the vehicle is programmed 1st Push Of This feature plays an alert when the power lift Know Before Starting Your Vehicle”...
- Page 182 Starts.” Press the back arrow button on the minutes” button on the touchscreen. Then press NOTE: touchscreen to return to the previous menu. the arrow back button on the touchscreen. Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile •...
- Page 183 • AUX Volume Match — If Equipped is new, the compass may appear erratic and between the “+” and “–” buttons on the touch- may need to be calibrated. You may calibrate screen. Then press the back arrow button on This feature provides the ability to tune the the compass by selecting the “Calibration”...
-
Page 184: Customer Programmable Features - Uconnect® 8.4 Settings
• Paired Audio Sources the box when selected. Then press the back Clear Personal Data arrow button on the touchscreen. After pressing the “Clear Personal Data Set- This feature shows which audio devices are tings” button on the touchscreen the following •... - Page 185 Radio Setup, Restore Settings, Clear Personal Display NOTE: Data and System Information. After pressing the “Display” button on the touch- To make changes to the Display Brightness screen the following settings will be available. with Headlights ON setting, the headlights NOTE: •...
- Page 186 • Navigation Turn-By-Turn In Cluster — Español/Français/Italiano/Nederlands/Polski/ Voice Português/Türk/Pусский) for all display nomen- After pressing the “Voice” button on the touch- If Equipped clature, including the trip functions and the screen the following settings will be available: When this feature is selected, the turn-by-turn navigation system (if equipped).
- Page 187 • Set Time Minutes Clock check-mark appears next to setting, indicating After pressing the “Clock” button on the touch- that the setting has been selected. To return to This feature will allow you to adjust the minutes. screen the following settings will be available: the previous menu, press the back arrow button The “Sync with GPS Time”...
- Page 188 • ParkSense® status, press and release the “Near” or “Far” been selected. Press the back arrow button on button. Then press the back arrow button on the the touchscreen to return to the previous menu. The ParkSense® system will scan for objects touchscreen.
- Page 189 mirrors will move back to their previous position NOTE: ting had been selected. Press the back arrow when the transmission is shifted out of RE- button on the touchscreen to return to the If your vehicle has experienced any damage VERSE.
- Page 190 • Rain Sensing Auto Wipers • Auto Dim High Beams — If Equipped Lights After pressing the “Lights” button on the touch- When this feature is selected, the system will When this feature is selected, the high beam screen the following settings will be available: automatically activate the windshield wipers if it headlights will deactivate automatically under •...
- Page 191 • Flash Lights With Lock Doors & Locks must push the RKE transmitter UNLOCK button After pressing the “Doors & Locks” button on twice to unlock the passenger’s doors. When When this feature is selected, the front and rear the touchscreen the following settings will be Unlock “All Doors”...
- Page 192 Remote Keyless Entry (RKE) transmitter lock or NOTE: showing that the setting has been selected. unlock buttons. To make your selection, press Press the back arrow button on the touchscreen The seat will return to the memorized seat the “Passive Entry” button on the touchscreen to return to the previous menu.
- Page 193 • Equalizer • AUX Volume Offset — If Equipped Engine Off Power Delay status, press the “0 seconds,” “45 seconds,” “5 minutes” or “10 When in this display you may adjust the Bass, This feature provides the ability to tune the minutes”...
- Page 194 • Paired Audio Sources the box when selected. Then press the back select “Yes” to restore, or “Cancel” to exit. Once arrow button on the touchscreen. the settings are restored, a pop up appears This feature shows which audio devices are stating "settings reset to default."...
-
Page 195: Uconnect® Radios - If Equipped
Uconnect® RADIOS — Connecting The iPod® Or External NOTE: USB Device If the audio device battery is completely IF EQUIPPED Use the connection cable to connect an iPod® discharged, it may not communicate with For detailed information about your Uconnect® or external USB device to the vehicles USB/ the iPod®/USB/MP3 control system until a radio, refer to your Uconnect®... -
Page 196: Second Row Usb Charging Port
NOTE: Getting Started For further information, refer to the Uconnect® • Screen(s) located in the rear of front User’s Manual. seats: Open the LCD screen cover by lifting up on cover. Second Row USB Charging Port Second row USB connector ports can be used for charging purposes only. -
Page 197: Dual Video Screen
• When the Video Screen(s) are open and a • The system can be controlled by the front DVD/Blu-ray™ Disc is inserted into the Disc seat occupants utilizing either the touch- player, the screen(s) turn(s) ON automati- screen radio, or by the rear seat occupants cally, the headphone transmitters turn ON using the remote control. -
Page 198: Blu-Ray™ Disc Player
Blu-ray™ Disc Player Using The Touchscreen Radio 3. RSE Mute Play A Blu-ray™ Disc Mute rear headphones for the current ignition The Blu-ray™ Disc player is located in the cycle. Pressing mute again will unmute rear center console. headphones. 4. RSE Remote Control Lock Out Press to enable/disable Remote Control func- tions. -
Page 199: Play Video Games
8. RSE Mode Play Video Games When connecting an external source to the AUX/HDMI input, ensure to follow the standard Connect the video game console to the Audio/ Select this button to change source for the color coding for the audio/video jacks: Video RCA/HDMI input jacks located on the active (highlighted) rear Screen/Channel on the side of each seat. - Page 200 2. To watch a DVD/Blu-ray™ Disc on Rear 1 (driver side rear passenger) ensure the Remote Control and Headphone channel selector switch is on Rear 1. 3. To watch a DVD/Blu-ray™ Disc on Rear 2 (passenger side rear passenger) ensure the Remote Control and Headphone channel selector switch is on Rear 2.
-
Page 201: Important Notes For Dual Video Screen System
Important Notes For Dual Video Blu-ray™ Disc Player Remote Screen System Control — If Equipped • The Rear Seat Entertainment System is able to transmit two channels of stereo audio and video simultaneously. • The Blu-ray™ Disc Player can play CDs, DVDs and Blu-ray™... -
Page 202: Replacing The Remote Control Batteries
3. SOURCE — Push to enter Source Selection 10. POPUP/MENU — Push to bring up repeat Replacing The Remote Control screen. and shuffle options, the Blu-ray™ Disc Batteries popup menu, the DVD title menu or to The remote control requires two AAA batteries 4. -
Page 203: Controls
• When both the headphone and the remote Controls control channel selector switches are on The headphone power indicator and controls Channel 2, the Remote is controlling are located on the right ear cup. Channel 2 and the headphones are tuned NOTE: to the audio on Channel 2. -
Page 204: Replacing The Headphone Batteries
Replacing The Headphone Batteries What Does This Warranty Cover? Except as warranty gives you specific legal rights. You specified below, this warranty covers any Prod- may also have other rights, which vary from Each set of headphones requires two AAA uct that in normal use is defective in workman- jurisdiction to jurisdiction. - Page 205 • To change the current audio mode, push the System Information the video on the screen. The factory default settings are already set for optimum viewing, so remote control’s SOURCE button. This will Disc Menu there is no need to change these settings under automatically select the next available audio When listening to a CD Audio or CD Data disc, normal circumstances.
- Page 206 • DVD: DVD-Video, DVD-Audio, AVCREC, • The player recognizes a maximum of 512 Recorded Discs AVCHD, DVD-VR files and 99 folders per CD-R and CD-RW The Blu-ray™ Disc player will play CD-R and disc. • CD: CD-DA, VCD, CD-TEXT CD-RW discs recorded in CD-Audio or •...
- Page 207 • To change the current file, use the remote always end with the extension ".wma" or (48.9° C). When this occurs, the player will ".WMA". To prevent incorrect playback, do control’s or Blu-ray™ Disc player’s button display "High Temp" and will shut off the Rear not use these extensions for any other types to advance to the next file, or the button to...
-
Page 208: Steering Wheel Audio Controls - If Equipped
STEERING WHEEL AUDIO Pushing the center button will make the radio current track, or to the beginning of the previous switch between the various modes available track if it is within eight seconds after the current CONTROLS — IF EQUIPPED (AM/FM/CD/AUX, etc.). -
Page 209: Radio Operation And Mobile Phones
4. Do not use solvents such as benzene, thin- RADIO OPERATION AND General Overview ner, cleaners, or anti-static sprays. Buttons On The Faceplate MOBILE PHONES The buttons on the faceplate are located below 5. Store the disc in its case after playing. Under certain conditions, the mobile phone the Uconnect®... - Page 210 Buttons On The Touchscreen 2. A/C Button buttons on the touchscreen are accessible on Press and release to change the current setting, the Uconnect® system screen. the indicator illuminates when A/C is ON. Per- forming this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
- Page 211 5. Front Defrost Button 8. Passenger Temperature Control CAUTION! Up Button Press and release to change the current airflow Failure to follow these cautions can cause setting to Defrost mode. The indicator illumi- Provides the passenger with independent tem- damage to the heating elements: nates when this feature is ON.
- Page 212 • Bi-Level Mode NOTE: blower setting. The blower speed decreases as you turn the blower control knob counterclock- Pressing this button while in Sync mode will Air comes from the instrument wise. automatically exit Sync. panel outlets and floor outlets. A slight amount of air is directed Buttons On The Touchscreen 10.
- Page 213 13. Climate Control OFF Button perature bar towards the red arrow button on improved fuel economy, press the A/C button to the touchscreen for warmer temperature set- turn off the air conditioning and manually adjust Press and release this button to turn the Cli- tings.
- Page 214 MAX A/C NOTE: 2. Next, adjust the temperature you would like In cold weather, use of Recirculation mode the system to maintain by adjusting the MAX A/C sets the control for maximum cooling may lead to excessive window fogging. The driver and passenger temperature buttons performance.
- Page 215 To provide you with maximum comfort in the NOTE: Automatic mode, during cold start-ups the Each of these features operates indepen- blower fan will remain on low until the engine dently from each other. If any feature is warms up. The blower will increase in speed controlled manually, temperature control and transition into Auto mode.
- Page 216 Controlling The Rear Climate Controls From The Front ATC Panel The Three-Zone ATC system allows for adjust- ment of the rear climate controls from the front ATC panel. To change the rear system settings: • Press "REAR" button to change control to rear control mode, Rear display will appear.
- Page 217 Once the desired temperature is displayed, the Headliner Mode CAUTION! (Continued) ATC System will automatically achieve and Air comes from the outlets in the head- cated in the right side trim panel behind the maintain that comfort level. When the system is liner.
- Page 218 Operating Tips Vacation Storage Outside Air Intake Any time you store your vehicle or keep it out of Make sure the air intake, located directly in front NOTE: service (i.e., vacation) for two weeks or more, of the windshield, is free of obstructions such as Refer to the chart at the end of this section run the air conditioning system at idle for about leaves.
- Page 219 Control Setting Suggestions For Various Weather Conditions...
-
Page 220: Starting And Operating
STARTING AND OPERATING • STARTING PROCEDURES ..... . .222 • Automatic Transmission ..... . .222 •... - Page 221 • ON-ROAD DRIVING TIPS ......236 • OFF-ROAD DRIVING TIPS ......237 •...
- Page 222 • TIRES — GENERAL INFORMATION ....249 • Tire Pressure ......249 •...
- Page 223 • Materials Added to Fuel ......264 • Carbon Monoxide Warnings ..... . .265 •...
- Page 224 • Recreational Towing — All-Wheel Drive Models (Single-Speed Transfer Case) ......280 •...
-
Page 225: Starting Procedures
STARTING PROCEDURES WARNING! (Continued) CAUTION! (Continued) Before starting your vehicle, adjust your seat, • Do not leave the Key Fob in or near the • Shift into PARK only after the vehicle has adjust the inside and outside mirrors, fasten vehicle (or in a location accessible to chil- come to a complete stop. -
Page 226: Keyless Enter-N-Go
Keyless Enter-N-Go™ 4. If you wish to stop the cranking of the engine twice to the OFF position. If the shift lever/ prior to the engine starting, push the button gear selector is not in PARK and the EN- This feature allows the again. -
Page 227: Extreme Cold Weather (Below -20°F Or −29°C)
• Press the ENGINE START/STOP button If Engine Fails To Start Clearing A Flooded Engine (Using ENGINE once to place the ignition to the ACC position START/STOP Button) (DID will display “ACC”). If the engine fails to start after you have followed WARNING! the “Normal Starting”... -
Page 228: Engine Block Heater - If Equipped
ENGINE BLOCK HEATER — AUTOMATIC TRANSMISSION WARNING! (Continued) IF EQUIPPED • Unintended movement of a vehicle could WARNING! The engine block heater warms the engine, and injure those in or near the vehicle. As with permits quicker starts in cold weather. Connect •... -
Page 229: Key Ignition Park Interlock
This system also locks the transmission in WARNING! (Continued) CAUTION! PARK whenever the ignition switch is in the • Never leave children alone in a vehicle, or Damage to the transmission may occur if the OFF position. with access to an unlocked vehicle. Allow- following precautions are not observed: •... -
Page 230: Eight-Speed Automatic Transmission
Eight-Speed Automatic Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the Transmission vehicle is stopped. Be sure to keep your foot on The transmission is controlled using a rotary the brake pedal when shifting between these electronic gear selector located on the center gears. - Page 231 PARK (P) WARNING! This range supplements the parking brake by • Never use the PARK position as a substi- locking the transmission. The engine can be tute for the parking brake. Always apply started in this range. Never attempt to use the parking brake fully when parked to PARK while the vehicle is in motion.
- Page 232 • DO NOT race the engine when shifting WARNING! (Continued) WARNING! (Continued) from PARK or NEUTRAL into another gear • Unintended movement of a vehicle could • Never leave children alone in a vehicle, or range, as this can damage the drivetrain. injure those in or near the vehicle.
- Page 233 shifts through all forward gears. The DRIVE Transmission Limp Home Mode WARNING! position provides optimum driving characteris- Transmission function is monitored electroni- Do not coast in NEUTRAL and never turn off tics under all normal operating conditions. cally for abnormal conditions. If a condition is the ignition to coast down a hill.
- Page 234 2. Shift the transmission into PARK, if possible. AutoStick condition would result. It will remain in the AutoStick is a driver-interactive transmission selected gear until another upshift or downshift If not, shift the transmission to NEUTRAL. feature providing manual shift control, giving is chosen, except as described below.
-
Page 235: All-Wheel Drive Operation
• Transmission shifting will be more noticeable ALL-WHEEL DRIVE Electronically Shifted Transfer Case when AutoStick is engaged. (Three-Position Switch) — OPERATION • The system may revert to automatic shift If Equipped This is an electronic shift transfer case and it is mode if a fault or overheat condition is Single-Speed Operating operated by the AWD Control Switch, which is... - Page 236 This electronically shifted transfer case is de- Transfer Case Position Indicator Messages If One Or More Shift Conditions Are Not Met: signed to be driven in the AWD AUTO position The Transfer Case Position Indicator messages 1. The indicator light for the current position will for normal street and highway conditions on dry (AWD AUTO and LOW RANGE) are located in remain ON.
-
Page 237: Shifting Procedure
turning and stopping speeds. Do not go faster LOW Range WARNING! than road conditions permit. All-Wheel Drive Low Range – This range pro- Always engage the parking brake when pow- vides low speed all-wheel drive. Locks the front ering down the vehicle if the “SERV AWD WARNING! and rear driveshafts together forcing the front Warning Light”... - Page 238 the selected position have been met. To Shifting can be performed with the vehicle roll- 4. After the desired position indicator light is retry a shift: return the control knob back ing 2 to 3 mph (3 to 5 km/h) or completely ON (not flashing), shift the transmission to the original position, make certain all stopped.
-
Page 239: On-Road Driving Tips
NEUTRAL Shift Procedure ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance 1. Bring the vehicle to a complete stop with the and a narrower track to make them capable of engine running. performing in a wide variety of off-road applica- 2. -
Page 240: Off-Road Driving Tips
OFF-ROAD DRIVING TIPS Driving Through Water Flowing Water Although your vehicle is capable of driving If the water is swift flowing and rising (as in through water, there are a number of precau- When To Use LOW Range — storm run-off), avoid crossing until the water tions that must be considered before entering If Equipped level recedes and/or the flow rate is reduced. -
Page 241: Driving In Snow, Mud And Sand
Driving In Snow, Mud And Sand If you stall or begin to lose forward motion while Remember, never drive diagonally across a climbing a steep hill, allow your vehicle to come hill always drive straight up or down. In heavy snow, when pulling a load, or for to a stop and immediately apply the brakes. -
Page 242: After Driving Off-Road
• After extended operation in mud, sand, wa- After Driving Off-Road POWER STEERING ter, or similar dirty conditions, have the radia- Off-road operation puts more stress on your tor, fan, brake rotors, wheels, brake linings, vehicle than does most on-road driving. After 3.6L Engine and axle yokes inspected and cleaned as going off-road, it is always a good idea to check... -
Page 243: L Engine
• Upon initial start-up in cold weather, the If the “SERVICE POWER STEER- there will be a substantial increase in ING” message and a flashing icon steering effort, especially at very low ve- power steering pump may make noise for are displayed on the DID screen, it hicle speeds and during parking maneu- a short amount of time. -
Page 244: Power Steering Fluid Check
Power Steering Fluid Check If necessary, add fluid to restore to the proper PARKING BRAKE indicated level. With a clean cloth, wipe any Checking the power steering fluid level at a de- Before leaving the vehicle, make sure that the spilled fluid from all surfaces. - Page 245 When the parking brake is applied with the WARNING! WARNING! (Continued) ignition switch in the ON position, the “Brake” • Never use the PARK position as a substi- • Do not leave the Key Fob in or near the Warning Light in the instrument cluster will tute for the parking brake.
-
Page 246: Electronic Brake Control System
Anti-Lock Brake System (ABS) ping wheel(s) and engine power is reduced to CAUTION! provide enhanced acceleration and stability. This system aids the driver in maintaining ve- If the “Brake” Warning Light remains on with hicle control under adverse braking conditions. A feature of the TCS system, Brake Limited the parking brake released, a brake system The system controls hydraulic brake pressure... -
Page 247: Electronic Roll Mitigation (Erm)
system, you must apply continuous braking Electronic Roll Mitigation (ERM) WARNING! (Continued) pressure during the stopping sequence (do not This system anticipates the potential for wheel rollovers, especially those that involve leav- “pump” the brakes). Do not reduce brake pedal lift by monitoring the driver’s steering wheel ing the roadway or striking objects or other pressure unless braking is no longer desired. - Page 248 appropriate wheel to assist in counteracting the AUTO Range (All-Wheel Drive Models) Or WARNING! oversteer or understeer condition. Two-Wheel Drive Models Electronic Stability Control (ESC) cannot • Oversteer - when the vehicle is turning more prevent the natural laws of physics from than appropriate for the steering wheel posi- This is the normal operating mode for ESC in acting on the vehicle, nor can it increase the...
-
Page 249: Trailer Sway Control (Tsc)
traction. To turn ESC on again, momentarily Trailer Sway Control (TSC) WARNING! press the “ESC OFF” switch. This will restore TSC uses sensors in the vehicle to recognize • When in “Partial Off” mode, the TCS func- the normal “ESC On” mode of operation. an excessively swaying trailer and will take the tionality of ESC, (except for the limited slip appropriate actions to attempt to stop the sway. -
Page 250: Hill Start Assist (Hsa)
HSA Activation Criteria WARNING! The following criteria must be met in order for HSA will provide assistance when starting on a If TSC activates while driving, slow the ve- HSA to activate: grade when pulling a trailer. hicle down, stop at the nearest safe location, •... -
Page 251: Ready Alert Braking
Ready Alert Braking ESC Activation/Malfunction Indicator WARNING! (Continued) Ready Alert Braking may reduce the time re- Light And ESC OFF Indicator Light • HSA is not a parking brake. Always apply quired to reach full braking during emergency the parking brake fully when leaving your braking situations. -
Page 252: Tires - General Information
erator and apply as little throttle as possible. Be TIRES — GENERAL WARNING! (Continued) sure to adapt your speed and driving to the INFORMATION • Over-inflation reduces a tire’s ability to prevailing road conditions. cushion shock. Objects on the road and NOTE: Tire Pressure chuckholes can cause damage that result... -
Page 253: Tire Inflation Pressures
NOTE: At least once a month: cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire • Check and adjust tire pressure with a good • Unequal tire pressures from side to side sidewall. quality pocket-type pressure gauge. Do not may cause erratic and unpredictable make a visual judgement when determining Check tire pressures more often if subject to a... -
Page 254: Tire Pressures For High Speed Operation
Tire Pressures For High Speed Radial Ply Tires of identical size and service description (Load Index and Speed Symbol). Operation The manufacturer advocates driving at safe WARNING! Tire Types speeds and within posted speed limits. Where Combining radial ply tires with other types of speed limits or conditions are such that the All Season Tires —... -
Page 255: Run Flat Tires - If Equipped
Summer tires do not contain the all season If you need snow tires, Run Flat Tires — If Equipped designation or mountain/snowflake symbol on select tires equivalent in Run Flat tires allow you the capability to drive 50 the tire sidewall. Use summer tires only in sets size and type to the origi- miles (80 km) at 50 mph (80 km/h) after a rapid of four;... - Page 256 letter “T” or “S” preceding the size designation. CAUTION! WARNING! (Continued) Example: T145/80D18 103M. Because of the reduced ground clearance, which apply to your spare. Failure to do so T, S = Temporary Spare Tire do not take your vehicle through an auto- could result in spare tire failure and loss of Since this tire has limited tread life, the original matic car wash with a compact or limited-use...
-
Page 257: Tire Spinning
use spare tire affects vehicle handling. Since it Tire Spinning Tread Wear Indicators is not the same as your original equipment tire, When stuck in mud, sand, snow, or ice condi- Tread wear indicators are in the original equip- replace (or repair) the original equipment tire tions, do not spin your vehicle’s wheels above ment tires to help you in determining when your and reinstall on the vehicle at the first opportu-... -
Page 258: Life Of Tire
Life Of Tire Loading Information placard or the Vehicle Cer- WARNING! tification Label for the size designation of your The service life of a tire is dependent upon Tires and the spare tire should be replaced tire. The Load Index and Speed Symbol for your varying factors including, but not limited to: after six years, regardless of the remaining tire will be found on the original equipment tire... -
Page 259: Tire Chains (Traction Devices)
• Install on Rear Tires Only. WARNING! WARNING! (Continued) • Due to limited clearance, use reduced size • Do not use a tire, wheel size or rating other • Failure to equip your vehicle with tires snow chains or traction devices with a maxi- than that specified for your vehicle. -
Page 260: Tire Rotation Recommendations
Refer to the “Service and Warranty Handbook” CAUTION! CAUTION! (Continued) for the proper maintenance intervals. More fre- • Observe the traction device manufactur- To avoid damage to your vehicle or tires, quent rotation is permissible if desired. The observe the following precautions: er’s instructions on the method of installa- reasons for any rapid or unusual wear should •... -
Page 261: Tire Pressure Monitor System (Tpms)
TIRE PRESSURE MONITOR The Tire Pressure Monitoring System (TPMS) The TPMS will continue to warn the driver of low will warn the driver of a low tire pressure based tire pressure as long as the condition exists, SYSTEM (TPMS) on the vehicle recommended cold tire placard and will not turn off until the tire pressure is at or The Tire Pressure Monitor System (TPMS) pressure. - Page 262 For example, your vehicle has a recommended NOTE: CAUTION! cold (parked for more than three hours) tire • The TPMS is not intended to replace nor- • The TPMS has been optimized for the placard pressure of 33 psi (227 kPa). If the mal tire care and maintenance, or to pro- original equipment tires and wheels.
-
Page 263: Tire Pressure Monitoring Low Pressure Warnings
Tire Pressure Monitoring Low The system will automatically update, the Pressure Warnings graphic display of the pressure value(s) will return to its original color and the Tire Pressure The Tire Pressure Monitoring Telltale Monitoring Telltale Light will extinguish once the Light will illuminate in the instrument updated tire pressure(s) have been received. -
Page 264: Tpms Deactivation - If Equipped
will not be present, and a pressure value will be NOTE: place of the pressure value. Once you repair displayed instead of dashes. A system fault can or replace the original road tire, and reinstall There is no tire pressure monitoring sensor occur by any of the following: it on the vehicle in place of the spare tire, the in the spare tire. -
Page 265: Fuel Requirements
flash on and off for 75 seconds and then remain FUEL REQUIREMENTS Besides using unleaded gasoline with the on and the Driver Information Display (DID) will proper octane rating, gasolines that contain display the “SERVICE TPM SYSTEM” message detergents, corrosion and stability additives are 3.6L Engine and then display dashes (--) in place of the recommended. -
Page 266: Methanol
as hard starting, stalling, and hesitations. If you Methanol noted that an increase in fuel consumption experience these symptoms, try another brand should be expected when using ethanol- (Methyl) is used in a variety of concentrations of gasoline before considering service for the blended fuels, due to the lower energy content when blended with unleaded gasoline. -
Page 267: Usage In Non-Flex Fuel Vehicles
E-85 Usage In Non-Flex Fuel More extensive repairs will be required for pro- Indiscriminate use of fuel system cleaning longed exposure to E-85 fuel. agents should be avoided. Many of these ma- Vehicles terials intended for gum and varnish removal Non-Flex Fuel Vehicles (FFV) are compatible MMT In Gasoline may contain active solvents or similar ingredi-... -
Page 268: Carbon Monoxide Warnings
FLEXIBLE FUEL (3.6L ENGINE WARNING! (Continued) WARNING! (Continued) ONLY) — IF EQUIPPED • Guard against carbon monoxide with • Do not inhale exhaust gases. They contain proper maintenance. Have the exhaust carbon monoxide, a colorless and odor- E-85 General Information system inspected every time the vehicle is less gas, which can kill. -
Page 269: Ethanol Fuel (E-85)
Observing these precautions will avoid possible WARNING! hard starting and/or significant deterioration in Ethanol vapors are extremely flammable and driveability during warm up. could cause serious personal injury. Never NOTE: have any smoking materials lit in or near the • When the ambient temperature is above vehicle when removing the fuel filler tube cap 90°... -
Page 270: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
Selection Of Engine Oil For Flexible Starting Replacement Parts Fuel Vehicles (E-85) And Gasoline The characteristics of E-85 fuel make it unsuit- Many components in your Flexible Fuel Vehicle able for use when ambient temperatures fall (FFV) are designed to be compatible with etha- Vehicles below 0°F (-18°C). -
Page 271: Adding Fuel
ADDING FUEL 4. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper 1. Press the fuel filler door release switch (lo- door while refueling. cated under the headlamp switch). NOTE: Only the correct size nozzle opens the latches allowing the flapper door to open. -
Page 272: Emergency Fuel Filler Door Release
• Ensure funnel is inserted fully to hold flapper WARNING! (Continued) door open. • A fire may result if fuel is pumped into a • Pour fuel into funnel opening. portable container that is inside of a ve- • Remove funnel from filler pipe, clean off prior to hicle. -
Page 273: Trailer Towing
TRAILER TOWING Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The GTW is the weight of the trailer plus the The GAWR is the maximum capacity of the front In this section you will find safety tips and weight of all cargo, consumables and equip- and rear axles. - Page 274 Frontal Area Weight-Distributing Hitch WARNING! The frontal area is the maximum height multi- A weight-distributing system works by applying • An improperly adjusted Weight Distributing plied by the maximum width of the front of a leverage through spring (load) bars. They are Hitch system may reduce handling, stabil- trailer.
-
Page 275: Trailer Towing Weights (Maximum Trailer Weight Ratings)
Trailer Towing Weights (Maximum Trailer Weight Ratings) GCWR (Gross Com- Max. GTW (Gross Max. Trailer Tongue Engine Model Frontal Area bined Wt. Rating) Trailer Wt.) Wt. (See Note) RWD Light Duty 3.6L 8,900 lbs (4,037 kg) 40 sq ft (3.72 sq m) 3,500 lbs (1,588 kg) 350 lbs (159 kg) Cooling... -
Page 276: Trailer Hitch Receiver Cover Removal - If Equipped
Trailer Hitch Receiver Cover Removal — If Equipped Your vehicle may be equipped with a trailer hitch receiver cover, this must be removed to access the trailer hitch receiver (if equipped). This cover is located at the bottom center of the rear fascia. -
Page 277: Trailer And Tongue Weight
Trailer And Tongue Weight Consider the following items when computing Towing Requirements the weight on the rear axle of the vehicle: Always load a trailer with 60% of the weight in To promote proper break-in of your new vehicle the front of the trailer. This places 10% of the drivetrain components, the following guidelines •... - Page 278 WARNING! WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used be- Improper towing can lead to a collision. Fol- 3. GAWR low these guidelines to make your trailer tween your vehicle and trailer. Always con- 4. Tongue weight rating for the trailer hitch towing as safe as possible: nect the chains to the hook retainers of the utilized.
- Page 279 • When replacing tires, refer to “Tires – Gen- Towing Requirements — Trailer Lights And WARNING! eral Information” in “Starting And Operating” Wiring • Do not connect trailer brakes to your vehi- for the proper tire replacement procedures. Whenever you pull a trailer, regardless of the cle’s hydraulic brake lines.
-
Page 280: Towing Tips
Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. The transmission controls include a drive strat- egy to avoid frequent shifting when towing. -
Page 281: Snow Plow
AutoStick Cooling System SNOW PLOW To reduce potential for engine and transmission • When using the AutoStick shift control, select Snow plows, winches, and other aftermarket overheating, take the following actions: equipment should not be added to the front end the highest gear that allows for adequate of your vehicle. -
Page 282: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF Rear-Wheel All-Wheel Drive Models With All-Wheel Drive Models With the Ground Drive Models Single-Speed Transfer Case Two-Speed Transfer Case • See Instructions • Transmission in PARK Flat Tow NONE NOT ALLOWED... -
Page 283: Recreational Towing - Rear-Wheel Drive Models
Recreational Towing — Rear-Wheel Recreational Towing — All-Wheel CAUTION! Drive Models Drive Models (Two-Speed Transfer Towing with the rear wheels on the ground DO NOT flat tow this vehicle. Damage to the Case) will cause severe transmission damage. drivetrain will result. The transfer case must be shifted into NEU- Damage from improper towing is not covered TRAL (N) and the transmission must be in... - Page 284 Shifting Into NEUTRAL (N) 1. Bring the vehicle to a complete stop, with the CAUTION! (Continued) engine running. • The transmission must be in PARK for WARNING! 2. Press and hold the brake pedal. recreational towing. You or others could be injured or killed if you •...
- Page 285 off. Turning the engine off will automatically met until the shift has been completed. If any of these requirements are not met place the transmission in PARK. before pressing the NEUTRAL (N) button 11. Press the ENGINE STOP/START button or are no longer met during the shift, the again (without pressing the brake pedal), if NEUTRAL (N) indicator light will flash needed, to turn the ignition switch to the...
- Page 286 3. Start the engine. 8. After the NEUTRAL (N) button has been NEUTRAL (N) indicator light will flash continuously until all requirements are released, the transfer case will shift to the 4. Press and hold the brake pedal. met or until the NEUTRAL (N) button is position indicated by the selector switch.
-
Page 288: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES • HAZARD WARNING FLASHERS ....286 • IF YOUR ENGINE OVERHEATS ....286 •... -
Page 289: Hazard Warning Flashers
HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS CAUTION! The Hazard Warning flasher switch is located In any of the following situations, you can Driving with a hot cooling system could dam- on the switch bank just above the climate reduce the potential for overheating by taking age your vehicle. -
Page 290: Wheel And Tire Torque Specifications
WHEEL AND TIRE TORQUE Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or SPECIFICATIONS loose particles. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been re- moved and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. -
Page 291: Jacking And Tire Changing
JACKING AND TIRE Rotate the plastic thumb screw on the end of the WARNING! (Continued) jack to loosen the jack and remove from the CHANGING • The jack is designed to be used as a tool bracket. for changing tires only. The jack should not be used to lift the vehicle for service pur- WARNING! poses. -
Page 292: Spare Tire Removal
Spare Tire Removal 4. Slide the tire out from under the vehicle and rotate it vertically behind the rear bumper. 1. Remove the jack tools from the bag. 2. Raise the rubber mat and remove the plug from storage compartment floor. 3. - Page 293 5. Spread the retaining tabs on the plastic plate 6. Slide the metal stamping up the steel exten- 7. Pinch the three short and two long tubes to and pull the metal stamping toward you to sion tube and winch cable. Rotate the metal remove the protective plate from the steel release it from the plastic plate.
-
Page 294: Preparations For Jacking
Preparations For Jacking 6. Block both the front and rear of the wheel WARNING! (Continued) diagonally opposite 1. Park the vehicle on a firm, level surface as • Turn on the Hazard Warning flasher. of the jacking posi- far from the edge of the roadway as pos- •... - Page 295 Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. Jack And Tool Assembly Lift Point Symbol On Sill Molding 3. For the front axle, place the jack on the body 1.
- Page 296 4. For a rear tire, place the jack in the slot on 7. Install the spare wheel/tire on the vehicle the rear tie-down bracket, just forward of the and install the lug nuts with the cone-shaped rear tire (as indicated by the triangular lift end toward the wheel.
- Page 297 10. Push out the small center cap using the 11. Insert the two long tubes on the plastic WARNING! jack tool from inside the aluminum road protective plate in the lug holes of the road To avoid the risk of forcing the vehicle off the wheel and position the wheel behind the wheel.
-
Page 298: Road Tire Installation
12. Slide the road wheel on the ground using 15. Have the aluminum road wheel and tire WARNING! the protective plate until it is directly under repaired as soon as possible and properly Do not use power tools to winch the tire up or the winch and between the rear bumper secure the spare tire, jack and tool kit. -
Page 299: Cap-Less Fuel Fill Funnel
For more information on the Cap-Less Fuel WARNING! WARNING! System refer to “Adding Fuel” in “Starting And To avoid the risk of forcing the vehicle off the Do not attempt jump-starting if the battery is Operating ” in this manual. jack, do not tighten the lug nuts fully until the frozen. -
Page 300: Jump-Starting Procedure
3. Remove the protective cover over the re- WARNING! (Continued) mote positive (+) battery post. Pull upward • Remove any metal jewelry such as rings, on the cover to remove it. watch bands and bracelets that could 4. If using another vehicle to jump-start the make an inadvertent electrical contact. - Page 301 3. Disconnect the positive (+) end of the jumper CAUTION! WARNING! cable from the positive (+) post of the Failure to follow these procedures could re- Do not connect the jumper cable to the booster battery. sult in damage to the charging system of the negative (-) post of the discharged battery.
-
Page 302: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE NOTE: WARNING! Press the ESC Off switch, to place the If your vehicle becomes stuck in mud, sand or Fast spinning tires can be dangerous. Electronic Stability Control (ESC) system in snow, it can often be moved using a rocking Forces generated by excessive wheel Partial Off mode, before rocking the ve- motion. -
Page 303: Manual Park Release
In order to move the vehicle in cases where the 3. Using a screwdriver or similar tool, push the CAUTION! (Continued) transmission will not shift out of PARK (such as metal latch in towards the tether strap. • Revving the engine or spinning the wheels a dead battery), a Manual Park Release is too fast may lead to transmission over- available. - Page 304 To Disengage the Manual Park Release Lever: 1. To disengage the Manual Park Release ap- ply tension upward while pushing the re- lease latch towards the tether to unlock the lever. Released Position Stowed Position NOTE: CAUTION! Be sure to replace the cover by snapping it Closing the armrest while the Manual Park back in place.
-
Page 305: Towing A Disabled Vehicle
TOWING A DISABLED operable, disabled vehicles may also be towed as described under “Recreational Towing” in the VEHICLE “Starting and Operating” section. This section describes procedures for towing a disabled vehicle using a commercial towing service. If the transmission and drivetrain are Towing Condition Wheels OFF the Ground Rear-Wheel Drive Models... - Page 306 Towing Condition Wheels OFF the Ground Rear-Wheel Drive Models All-Wheel Drive Models All-Wheel Drive Models With Single-Speed With Two-Speed Transfer Transfer Case Case If Transmission Is Operable: • Transmission in NEUTRAL • 30 mph (48 km/h) Front NOT ALLOWED NOT ALLOWED Wheel Lift or Dolly Tow max speed •...
-
Page 307: Rear Wheel Drive Models
Rear Wheel Drive Models with the front wheels raised and the rear wheels CAUTION! on a towing dolly, or (when using a suitable The manufacturer recommends towing your ve- • Front or rear wheel lifts must not be used. steering wheel stabilizer to hold the front wheels hicle with all four wheels OFF the ground using Internal damage to the transmission or in the straight position) with the rear wheels... -
Page 308: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE • ENGINE COMPARTMENT — 3.6L ....307 • ENGINE COMPARTMENT — 5.7L ....308 •... - Page 309 • Automatic Transmission ......325 • Appearance Care And Protection From Corrosion ..326 •...
-
Page 310: Engine Compartment — 3.6L
ENGINE COMPARTMENT — 3.6L 1 — Power Distribution Center (Fuses) 6 — Air Cleaner Filter 2 — Engine Oil Dipstick 7 — Washer Fluid Reservoir 3 — Engine Oil Fill 8 — Coolant Pressure Cap (Radiator) 4 — Brake Fluid Reservoir 9 —... -
Page 311: Engine Compartment — 5.7L
ENGINE COMPARTMENT — 5.7L 1 — Remote Jump Start Terminals 6 — Washer Fluid Reservoir 2 — Engine Oil Fill 7 — Engine Oil Dipstick 3 — Air Filter Cleaner 8 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 9 —... -
Page 312: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC DEALER SERVICE CAUTION! SYSTEM (OBD II) Your authorized dealer has the qualified service • Prolonged driving with the MIL on could personnel, special tools, and equipment to per- Your vehicle is equipped with a sophisticated cause further damage to the emission con- form all service operations in an expert manner. -
Page 313: Maintenance Procedures
MAINTENANCE PROCEDURES Checking the oil while the vehicle is on level CAUTION! (Continued) ground will improve the accuracy of the oil level The pages that follow contain the required • Your vehicle has been built with improved readings. Always maintain the oil level within maintenance services determined by the engi- fluids that protect the performance and the SAFE zone on the dipstick. - Page 314 American Petroleum Institute (API) Engine are API certified and meet the requirements of Engine Oil Viscosity — 5.7L Engine Oil Identification Symbol Chrysler Material Standard MS-6395. For coun- MOPAR® SAE 5W-20 engine oil or equivalent tries that use the ACEA European Oil Catego- such as Pennzoil®...
-
Page 315: Engine Air Cleaner Filter
is an engineered product and its performance Engine Air Cleaner Filter Maintenance-Free Battery may be impaired by supplemental additives. Refer to the “Service and Warranty Handbook” Your vehicle is equipped with a maintenance- for the proper maintenance intervals. free battery. You will never have to add water, Disposing Of Used Engine Oil And Oil nor is periodic maintenance required. -
Page 316: Air Conditioner Maintenance
Air Conditioner Maintenance WARNING! (Continued) WARNING! (Continued) For best possible performance, your air condi- • Battery posts, terminals, and related ac- • The air conditioning system contains re- tioner should be checked and serviced by an cessories contain lead and lead com- frigerant under high pressure. - Page 317 be performed by authorized dealer or other Air Conditioning Filter Replacement service facilities using recovery and recycling (A/C Air Filter) equipment. Refer to the “Service and Warranty Handbook” for the proper maintenance intervals. NOTE: Use only manufacturer approved A/C sys- WARNING! tem PAG compressor oil and refrigerants.
- Page 318 3. Pull the right hand side of the glove compart- ment door toward the rear of the vehicle to disengage the glove compartment door from its hinges. NOTE: When disengaging the glove compartment door from its hinges, there will be some resistance.
-
Page 319: Body Lubrication
Body Lubrication Windshield Wiper Blades CAUTION! Locks and all body pivot points, including such Clean the rubber edges of the wiper blades and The A/C air filter is identified with an arrow to items as seat tracks, door hinge pivot points the windshield periodically with a sponge or soft indicate airflow direction through the filter. -
Page 320: Adding Washer Fluid
Rear Wiper Blade Removal/Installation 3. Grab the bottom of the wiper blade and Adding Washer Fluid rotate it forward to unsnap the blade pivot This vehicle is equipped with a Driver Information 1. Lift the pivot cap on the rear wiper arm pin from the wiper blade holder. -
Page 321: Exhaust System
WARNING! WARNING! CAUTION! • Exhaust gases can injure or kill. They • The catalytic converter requires the use of Commercially available windshield washer solvents are flammable. They could ignite contain carbon monoxide (CO), which is unleaded fuel only. Leaded gasoline will and burn you. -
Page 322: Cooling System
NOTE: Cooling System Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tight- Intentional tampering with emissions con- ness of the connection at the coolant recovery trol systems can result in civil penalties WARNING! bottle and radiator. Inspect the entire system for being assessed against you. - Page 323 If the engine coolant (antifreeze) is dirty or CAUTION! CAUTION! (Continued) contains visible sediment, have an authorized • Mixing of engine coolant (antifreeze) other • Do not use water alone or alcohol-based dealer clean and flush with OAT coolant (anti- than specified Organic Additive Technol- engine coolant (antifreeze) products.
- Page 324 Please review these recommendations for us- Please note that it is the owner’s responsibility Cooling System Pressure Cap ing Organic Additive Technology (OAT) engine to maintain the proper level of protection The cap must be fully tightened to prevent loss coolant (antifreeze) that meets the require- against freezing according to the temperatures of engine coolant (antifreeze), and to ensure...
- Page 325 • Check the coolant freeze point in the radiator Disposal Of Used Engine Coolant ture is satisfactory, the coolant bottle need only Used ethylene glycol-based engine coolant (an- be checked once a month. and in the coolant expansion bottle. If engine tifreeze) is a regulated substance requiring coolant (antifreeze) needs to be added, the When additional engine coolant (antifreeze) is...
-
Page 326: Brake System
Brake System Fluid Level Check — Brake Master WARNING! Cylinder In order to assure brake system performance, • Use only manufacturer’s recommended The fluid level of the master cylinder should be all brake system components should be in- brake fluid. Refer to “Fluids, Lubricants, checked when performing under the hood ser- spected periodically. - Page 327 Front Axle Fluid Level Check Selection Of Lubricant WARNING! (Continued) The front axle oil level needs to be no lower than Use only the manufacturer’s recommended • Overfilling the brake fluid reservoir can 1/8 in (3 mm) below the bottom of the fill hole. fluid.
-
Page 328: Automatic Transmission
NOTE: CAUTION! CAUTION! No chemical flushes should be used in any When installing plugs, do not overtighten. Do not use chemical flushes in your trans- transmission; only the approved lubricant You could damage them and cause them to mission as the chemicals can damage your should be used. -
Page 329: Appearance Care And Protection From Corrosion
those that are sprayed on trees and road sur- Washing CAUTION! faces during other seasons are highly corrosive • Wash your vehicle regularly. Always wash If a transmission fluid leak occurs, visit your to the metal in your vehicle. Outside parking, your vehicle in the shade using MOPAR®... - Page 330 • If you carry special cargo such as chemicals, NOTE: CAUTION! (Continued) fertilizers, de-icer salt, etc., be sure that such If your vehicle is equipped with Dark Vapor • Use of power washers exceeding 1,200 psi materials are well packaged and sealed. or Black Satin Chrome wheels DO NOT USE (8 274 kPa) can result in damage or removal •...
- Page 331 Stain Repel Fabric Cleaning Procedure — Interior Care WARNING! If Equipped Use MOPAR® Total Clean to clean fabric uphol- Do not use volatile solvents for cleaning Stain Repel seats may be cleaned in the follow- stery and carpeting. purposes. Many are potentially flammable, ing manner: Use MOPAR®...
-
Page 332: Fuses
with a dry cloth. To remove road dirt, wash with 1. Clean with a wet soft rag. A mild soap WARNING! (Continued) a mild soap solution followed by rinsing. solution may be used, but do not use high ing for cuts, frays, or loose parts. Damaged alcohol content or abrasive cleaners. -
Page 333: Power Distribution Center
Power Distribution Center WARNING! (Continued) The Power Distribution Center is located in the • Before replacing a fuse, make sure that the engine compartment near the battery. This cen- ignition is off and that all the other services ter contains cartridge fuses, micro fuses, relays, are switched off and/or disengaged. - Page 334 Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Trailer Tow Electric Brake - If Equipped 40 Amp Green – Body Controller #3 / Power Locks 40 Amp Green – Blower Motor Front 40 Amp Green – Body Controller #4 / Interior Lights #2 30 Amp Pink –...
- Page 335 Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Sunroof - If Equipped 30 Amp Pink – Rear Defroster 25 Amp Clear – Rear Blower Motor - If Equipped 30 Amp Pink – Power Inverter 115V AC - If Equipped 30 Amp Pink –...
- Page 336 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Purging Pump (Diesel engine only) – 15 Amp Blue Transmission Control Module – 10 Amp Red Transmission Control Module/PM Sensor (Diesel engine only) – 10 Amp Red Air Conditioning Clutch –...
- Page 337 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Universal Garage Door Opener / Compass / Anti-Intrusion Module – 20 Amp Yellow Trailer Tow Right Turn/Stop Lights – 10 Amp Red Steering Column Control Module/ Cruise Control – 10 Amp Red Fuel Door –...
-
Page 338: Vehicle Storage
Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Front Heated Seats - If Equipped – 10 Amp Red Climate Control / Driver Assistance Systems Module F100 – 10 Amp Red Active Damping - If Equipped F101 – 15 Amp Blue Electrochromatic Mirror/Smart High Beams - If Equipped F103 –... -
Page 339: Replacement Bulbs
REPLACEMENT BULBS Interior Bulbs Bulb Number Glove Box Lamp Grab Handle Lamp L002825W5W Overhead Console Reading Lamps VT4976 Visor Vanity Lamp V26377 Rear Cargo Lamp 214–2 Underpanel Courtesy Lamps Instrument Cluster (General Illumination) Telltale/Hazard Lamp Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Xenon) Headlamps D3S (Service at Authorized Dealer) Low Beam/High Beam/Daytime Running Lamp (DRL) Bi-Halogen HIR2LL... - Page 340 Bulb Number Front Park/Turn Signal Lamps (Base) 3157NAK Front Turn Signal Lamps (Uplevel & Premium) 3157NAK Front Park Lamp/Daytime Running Lamp (Uplevel & Premium) LED (Serviced at Authorized Dealer) Front Side Marker Lamps LED (Serviced at Authorized Dealer) Front Fog Lamps Rear Tail Lamps/Sidemarker Lamps LED (Serviced at Authorized Dealer) Rear Stop/Turn Signal Lamps...
-
Page 341: Bulb Replacement
BULB REPLACEMENT 4. Firmly grasp the access cap and rotate WARNING! (Continued) counterclockwise to remove lamp housing. headlamps when the headlamp switch is NOTE: 5. Firmly grasp the low/high beam bulb and turned ON. It may cause serious electrical Lens fogging can occur under certain atmo- connector assembly and rotate counter- shock or electrocution if not serviced prop- spheric conditions. -
Page 342: Front Turn Signal
Front Turn Signal 3. Install the bulb and connector assembly into Rear Liftgate Mounted Back-up the fog lamp housing and rotate the connec- Lamps 1. Open the hood. tor one-quarter turn clockwise to lock it in 1. Raise the liftgate. 2. -
Page 343: Fluid Capacities
FLUID CAPACITIES Metric Fuel (Approximate) 3.6L and 5.7L Engines 25 Gallons 94 Liters Engine Oil With Filter 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters 5.7L Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters Cooling System * 3.6L Engine (MOPAR®... -
Page 344: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-90032. Engine Oil – 3.6L Engine We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, Shell Helix®... - Page 345 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other • Do not use water alone or alcohol-based than specified Organic Additive Technol- engine coolant (antifreeze) products. Do ogy (OAT) engine coolant (antifreeze), not use additional rust inhibitors or antirust may result in engine damage and may products, as they may not be compatible decrease corrosion protection.
-
Page 346: Chassis
Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar® ZF 8&9 Speed ATF™ Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer Case – 3.6L Engine We recommend you use Shell Automatic Transmission Fluid. -
Page 347: Vehicle Specifications
VEHICLE SPECIFICATIONS Engine 3.6L 5.7L Power 148 kW @ 5,100 RPM 240 kW @ 5,000 RPM Torque 315 N.m @ 3,900 RPM 500 N.m @ 4,000 RPM Maximum Vehicle Speed Consult your Salesperson Consult your Salesperson NOTE: A chime will sound if the vehicle speed exceeds 75 mph (120 km/h). -
Page 348: Maintenance Schedules
MAINTENANCE SCHEDULES • MAINTENANCE SCHEDULE ..... .346... -
Page 349: Maintenance Schedule
MAINTENANCE SCHEDULE Refer to the “Service and Warranty Handbook” for maintenance schedules. -
Page 350: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE • IF YOU NEED ASSISTANCE ..... .348... -
Page 351: If You Need Assistance
• Service history of your vehicle. IF YOU NEED ASSISTANCE When you contact the distributor, please pro- vide all of the following information: • An accurate description of the problem and The manufacturer’s distributors are vitally inter- • Your name, address and phone number. ested in your satisfaction with their products the conditions under which it occurs. -
Page 354: Index
INDEX... - Page 355 Adaptive Cruise Control (ACC) Air Conditioning Refrigerant ..313, 314 Fluid Type ... . .325, 343 (Cruise Control) ....107 Air Conditioning System .
- Page 356 Capacities, Fluid ....340 How To Stow An Unused ALR Seat Coolant Level ....322 Caps, Filler Belt .
- Page 357 Child-Protection Door Lock — Hazard Warning Flasher ..286 Exhaust Gas Caution ..62, 265 Rear Doors ....21 Jacking .
- Page 358 Fluids .....343 Gauges Illuminated Entry ....17 Fluids, Lubricants and Genuine Parts .
- Page 359 Keyless Enter-N-Go ... . .223 Center Mounted Stop ..339 Vanity Mirror ....73 Keyless Enter-N-Go™...
- Page 360 Heated ....73 Viscosity ....311, 340 Preparation for Jacking ...291 Outside .
- Page 361 Shifting out of Transfer Case Safety Checks Outside Vehicle ..63 Pregnant Women ... . .34 Neutral (N) ....282 Safety Tips .
- Page 362 Snow Tires ....252 Supplemental Restraint System - Airbag. . .39 Spare Tire ....288 Spare Tire .
- Page 363 Maintenance ....325 Vanity Mirrors ....73 Windshield Wiper Blades ..316 Shifting .
- Page 738 Durango 15WD01-126-ARA-AA...
Need help?
Do you have a question about the Durango 2015 and is the answer not in the manual?
Questions and answers