Page 1 FIAT 500L ® 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION versions are not expressly indicated in the text. Therefore, you should only consider the information which is related Dear Customer, to the trim level, engine, and version that you have Congratulations on selecting your new vehicle. Be assured purchased.
Page 7: Symbols
INTRODUCTION Since the specification of your vehicle depends on the items Symbols of equipment ordered, certain descriptions and illustra- Consult the following table for a description of the symbols tions may differ from your vehicle’s equipment. that may be used on your vehicle or throughout this The detailed index at the back of this Owner’s Manual Owner’s Manual: contains a complete listing of all subjects.
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INSTRUMENT PANEL .....10 REAR VIEW .
Page 10: Front View
8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Exterior Mirrors 2 — Headlights 5 — Doors 3 — Windshield 6 — Wheels/Tires...
Page 11: Rear View
GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12: Instrument Panel
10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Multifunction Lever (Behind Steering Wheel) 5 — Windshield Wiper Lever 3 — Steering Wheel 6 — Radio...
Page 13: Interior
GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior 1 — Seats 4 — Climate Controls 2 — Gear Selector 5 — Upper Glove Compartment 3 — Switch Panel 6 — Lower Glove Compartment...
Page 15 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .17 DOORS .
Page 16 14 GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS ..... .34 EXTERIOR LIGHTS ..... . .43 ▫...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 CLIMATE CONTROLS .....51 HOOD ....... .69 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT ....83 ROOF LUGGAGE RACK — IF EQUIPPED ..87 ▫...
Page 19: Keys
GETTING TO KNOW YOUR VEHICLE 17 KEYS To Unlock The Doors, And Liftgate Push and release the unlock button on the key fob once to Key With Remote Control unlock the driver’s door or twice, within five seconds, to The Remote Keyless Entry (RKE) key fob contains an unlock all doors, and liftgate.
Page 20 18 GETTING TO KNOW YOUR VEHICLE Replacing The Battery In The Key With Remote To replace the battery, proceed as follows: Control 1. Push mechanical release button to open the mechanical key. 2. Turn the screw to unlock using a small screwdriver. 3.
Page 21: Ignition Switch
GETTING TO KNOW YOUR VEHICLE 19 Request For Additional Remote Controls IGNITION SWITCH The system can recognize up to eight remote controls. Ignition Switch Should a new remote control be necessary, go to an The ignition switch can be turned to three different posi- authorized dealer, taking an ID document and the car tions: ownership documents.
Page 22 20 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
Page 23: Key-In-Ignition Reminder
GETTING TO KNOW YOUR VEHICLE 21 Key-In-Ignition Reminder CAUTION! Opening the driver’s door when the key is in the ignition • Always remove the Sentry Key from the vehicle and and the ignition switch position is in the OFF/LOCK lock all doors when leaving the vehicle unattended. position, a signal sounds to remove the key.
Page 24: General Information
22 GETTING TO KNOW YOUR VEHICLE General Information visible signals: the horn will pulse, the park lamps and/or turn signals will flash, and the vehicle security light on the The following regulatory statement applies to all radio instrument panel will flash. frequency (RF) devices equipped in this vehicle: To Arm The System This device complies with Part 15 of the FCC Rules and...
Page 25: To Disarm The System
GETTING TO KNOW YOUR VEHICLE 23 If the horn sounds a second time, check that all doors, hood Central Lock/Unlock (Switch Safe Lock Device) — and liftgate are closed correctly, then rearm the system. If Equipped If the vehicle security alarm sounds the horn a second time This safety device prevents the operation of the interior even when all doors, hood and liftgate are correctly closed, door handles and the door locking/unlocking button.
Page 26: Doors
24 GETTING TO KNOW YOUR VEHICLE • LED ON: Doors locked. Pushing the central lock/unlock Activating The Safe Lock Device button once will unlock all doors. The LED will switch The Safe Lock device is enabled on all the doors by quickly off once the doors are unlocked.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 NOTE: With central locking active (LED ON), opening one WARNING! (Continued) of the front doors, it is possible to perform a central into FIRST gear or REVERSE, apply the parking unlocking (LED OFF). With central locking active (LED brake, turn the vehicle OFF, remove the key fobs ON), in order to open one of the rear passenger doors, it is from vehicle, and lock all doors.
Page 28: Doors Lock With One Or More Doors Open
26 GETTING TO KNOW YOUR VEHICLE Child-Protection Door Lock System (Rear Doors) CAUTION! To provide a safer environment for small children riding in An unlocked vehicle is an invitation. Always remove the rear seats, the rear doors are equipped with Child- the key from the ignition and lock all doors when Protection Door Lock system.
Page 29: Seats
GETTING TO KNOW YOUR VEHICLE 27 SEATS Manual Adjustment (Front Seats) Seats are a part of the Occupant Restraint System of the WARNING! vehicle. • Adjusting a seat while the vehicle is moving is WARNING! dangerous. The sudden movement of the seat could cause you to lose control.
Page 30 28 GETTING TO KNOW YOUR VEHICLE Forward/Rearward Adjustment Seat Height Adjustment The adjusting bar is located at the front of the seats, near The seat height adjustment lever is located on the outboard the floor. side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat While sitting in the seat, lift up on the bar and move the height.
Page 31: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE 29 and lift the lever. Release the lever once the seatback is in WARNING! (Continued) the upright position. • Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed.
Page 32 30 GETTING TO KNOW YOUR VEHICLE While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
Page 33: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 31 Power Adjustment (Front Seats) — If Equipped Heated Seats — If Equipped On some models, the front driver and passenger seats may Power Lumbar — If Equipped be equipped with heaters in both the seat cushions and Push the power lumbar switch to adjust the lumbar seatbacks.
Page 34: Fold And Tumble Rear Seat
32 GETTING TO KNOW YOUR VEHICLE Fold And Tumble Rear Seat WARNING! NOTE: • Persons who are unable to feel pain to the skin • Prior to folding the rear seat, it may be necessary to because of advanced age, chronic illness, diabetes, reposition the front seats.
Page 35 GETTING TO KNOW YOUR VEHICLE 33 2. Fold the seatback forward. 3. Locate the seatback recline lever on the outboard side of the seat and lift upward on the lever. Seatback Folded Seatback Recline Lever NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for an extended period of time.
Page 36: Rear Armrest - If Equipped
34 GETTING TO KNOW YOUR VEHICLE 4. Slowly flip the entire seat forward. Rear Armrest — If Equipped To use the armrest, fold it downward. Folding Rear Seat 5. Slowly flip the entire seat rearward and firmly lock the Folding Rear Seat Armrest seat into position.
Page 37: Reactive Head Restraints - Front Seats
GETTING TO KNOW YOUR VEHICLE 35 WARNING! • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
Page 38: Rear Head Restraint Adjustment
36 GETTING TO KNOW YOUR VEHICLE To raise the outboard head restraints, pull upward on the WARNING! head restraint. To lower the head restraints, push the • A loose head restraint thrown forward in a collision adjustment button located at the base of the head restraint, and push downward on the head restraint.
Page 39: Rear Head Restraint Removal
GETTING TO KNOW YOUR VEHICLE 37 reinstall the head restraint, put the head restraint posts into restraint up. To reinstall the head restraint, put the head the holes and push downward. Then adjust it to the restraint posts into the holes and push downward. Then, appropriate height.
Page 40: Mirrors
38 GETTING TO KNOW YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 41: Automatic Dimming Mirror - If Equipped
GETTING TO KNOW YOUR VEHICLE 39 Headlight glare from vehicles behind you can be reduced NOTE: This feature is disabled when the vehicle is moving by moving the small control under the mirror to the night in REVERSE. position (toward the rear of the vehicle). The mirror should be adjusted while the small control under the mirror is set in the day position (toward the windshield).
Page 42: Conversation Mirror - If Equipped
40 GETTING TO KNOW YOUR VEHICLE Conversation Mirror — If Equipped To gain access to the conversation mirror, pull downward on the mirror to the open position. There is a conversation mirror located at the top of the overhead console. Conversation Mirror Conversation Mirror Location...
Page 43: Power Mirrors
GETTING TO KNOW YOUR VEHICLE 41 Power Mirrors Folding Mirrors The power mirror controls are located on the driver’s door The exterior mirrors are hinged to allow the mirror to pivot trim panel. To adjust a mirror, turn the control knob toward forward or rearward to help avoid damage.
Page 44: Illuminated Vanity Mirrors - If Equipped
42 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped Sun Visor “Slide-On-Rod” Feature An illuminated vanity mirror is located on the sun visor. To The sun visor “Slide-On-Rod” feature allows for additional use the mirror, rotate the sun visor downward and swing flexibility in positioning the visor to block out the sun.
Page 45: Exterior Lights
GETTING TO KNOW YOUR VEHICLE 43 EXTERIOR LIGHTS Rotate the end of the multifunction lever upward to the first detent for headlight operation. Headlights The multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight high beams, lane change assist and turn signals.
Page 46: Daytime Running Lights - If Equipped
44 GETTING TO KNOW YOUR VEHICLE Daytime Running Lights — If Equipped Parking Lights To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol. To turn on the parking lights, remove the key or turn the ignition to STOP (OFF/LOCK) position NOTE: The low beams and side/tail lights will not be on and turn on the headlights.
Page 47: Front Fog Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 45 Deactivation When the vehicle is unlocked, the low beams and parking lights will turn on for the time specified. Once the door is Pull the multifunction lever toward the steering wheel and opened, the lights will remain on for an additional three hold it for more than two seconds.
Page 48 46 GETTING TO KNOW YOUR VEHICLE Using the switch on the bottom of the overhead console, Push the switch to the off/left position from its center push the switch to the on/right position from its center position and the lights are always off. position and the lights are always on.
Page 49 GETTING TO KNOW YOUR VEHICLE 47 Leave the switch in the center position, and the lights are turned on and off when the doors are opened or closed. Map/Reading Light Switches CAUTION! Center Position The switches on the left and right sides of the overhead Before getting out of the vehicle be sure that the switch is in the center position or that the lights are off to console controls the map or reading function of the lights.
Page 50: Wipers And Washers
48 GETTING TO KNOW YOUR VEHICLE Interior Light Timing (Center Position) NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position. There are four different modes of operation that can be activated in this position: Front Wiper Operation •...
Page 51 GETTING TO KNOW YOUR VEHICLE 49 Intermittent Wiper System Intermittent Low Speed — Rotate the end of the lever upward to the first detent for low intermittent speed to operate the wipers with a fixed pause of ten seconds. Intermittent High Speed — Rotate the end of the lever upward to the second detent for high intermittent speed to operate the wipers with a delay that is dependent on the speed of the vehicle.
Page 52: Rear Wiper/Washer Operation
50 GETTING TO KNOW YOUR VEHICLE • In synchronous mode (at half the speed of the front CAUTION! (Continued) window wiper), when the front windshield wiper is the wiper motor may occur when the vehicle is operating and the lever is in the (intermittent) restarted.
Page 53: Climate Controls
GETTING TO KNOW YOUR VEHICLE 51 window wiper as well. Releasing the windshield wiper CLIMATE CONTROLS lever will activate the smart washing function, as described Manual Climate Control Overview for the windscreen wiper. Rear Window Washer Operation Manual Climate Controls Deactivation The function stops when the windshield wiper lever is released.
Page 54 52 GETTING TO KNOW YOUR VEHICLE Manual Climate Control Descriptions Icon Description A/C Button Push the A/C button to engage the Air Conditioning (A/C). A LED will illuminate when the A/C system is engaged. Recirculation Button Push and release this button to change the system between recirculation mode and outside air mode.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Icon Description Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotat- ing the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures.
Page 56 54 GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 57: Automatic Climate Control Overview
GETTING TO KNOW YOUR VEHICLE 55 NOTE: The power of the electric heater is modulated Automatic Climate Control Overview according to the battery voltage. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear win- dow.
Page 58 56 GETTING TO KNOW YOUR VEHICLE Icon Description Recirculation Button Push and release this button to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.
Page 59 GETTING TO KNOW YOUR VEHICLE 57 Icon Description Rear Defrost Button Push and release the Rear Defrost Control button to turn ON the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window de- froster is on.
Page 60 58 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 61: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE 59 Climate Control Functions CAUTION! A/C (Air Conditioning) Failure to follow these cautions can cause damage to The Air Conditioning (A/C) button allows the operator to the heating elements: • Use care when washing the inside of the rear win- manually activate or deactivate the air conditioning sys- tem.
Page 62: Automatic Temperature Control (Atc) - If
60 GETTING TO KNOW YOUR VEHICLE Recirculation Automatic Temperature Control (ATC) — If Equipped When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, you may wish to recirculate Automatic Operation interior air by pushing the Recirculation control button. 1.
Page 63: Operating Tips
GETTING TO KNOW YOUR VEHICLE 61 To provide you with maximum comfort in the Automatic Winter Operation mode during cold start-ups, the blower fan will remain on To ensure the best possible heater and defroster perfor- low until the engine warms up. The blower will increase in mance, make sure the engine cooling system is functioning speed and transition into Auto mode.
Page 64 62 GETTING TO KNOW YOUR VEHICLE Window Fogging Outside Air Intake Vehicle windows tend to fog on the inside in mild, rainy, Make sure the air intake, located directly in front of the and/or humid weather. To clear the windows, select De- windshield, is free of obstructions, such as leaves.
Page 65 GETTING TO KNOW YOUR VEHICLE 63 Operating Tips Chart...
Page 66: Windows
64 GETTING TO KNOW YOUR VEHICLE WINDOWS Power Windows Power Window Controls The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door, which operate the front passenger window and a single switch on each rear door that operates the rear passenger door window.
Page 67 GETTING TO KNOW YOUR VEHICLE 65 To stop the window during an Auto-Up operation, push or WARNING! pull again the window switch. Never leave children unattended in a vehicle, and do To close the window part way, pull the window switch not let children play with power windows.
Page 68: Wind Buffeting
66 GETTING TO KNOW YOUR VEHICLE Resetting The Auto-Up Feature POWER SUNROOF — IF EQUIPPED Should the Auto-Up feature stop working, the window The sunroof has two glass panels (the front one is opera- probably needs to be reset. To reset Auto-Up: tional and the rear one fixed) and is equipped with an electrically operated sun blind.
Page 69: Opening
GETTING TO KNOW YOUR VEHICLE 67 open the sunroof partway, pull the power sunroof switch WARNING! briefly and release it when you want the sunroof to stop. • Never leave children alone in a vehicle, or with NOTE: During Express Open operation, any movement of access to an unlocked vehicle.
Page 70: Sunroof Reinitialization
68 GETTING TO KNOW YOUR VEHICLE Sunroof Reinitialization can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows 1. Place the ignition in the ON/RUN mode. together to minimize the buffeting. If the buffeting occurs 2.
Page 71: Hood
GETTING TO KNOW YOUR VEHICLE 69 Closing HOOD With the sun blind fully open, pull and hold the power sun Opening blind switch for approximately one second and release. To open the hood, two latches must be released to open the The sun blind will close completely, then stop automati- hood.
Page 72: Closing
70 GETTING TO KNOW YOUR VEHICLE 2. Move to the outside of the vehicle and push the red Closing safety catch lever to the left and raise the hood. The safety catch lever is located under the center front edge WARNING! of the hood.
Page 73: Liftgate
GETTING TO KNOW YOUR VEHICLE 71 LIFTGATE WARNING! Opening • Driving with the liftgate open can allow poisonous To unlock the liftgate, use the key fob or activate the central exhaust gases into your vehicle. You and your pas- locking button located on the instrument panel below the sengers could be injured by these fumes.
Page 74: Cargo Area Features
72 GETTING TO KNOW YOUR VEHICLE 2. Take the screwdriver from the tool box supplied. 3. With the screwdriver, remove the yellow tab. Liftgate Emergency Release Tab Cargo Area Features Rear Cargo Storage Features Liftgate Emergency Release Yellow Tab Location 4.
Page 75 GETTING TO KNOW YOUR VEHICLE 73 • Position 2 (platform at threshold level) permits a level load threshold to facilitate loading/unloading of objects in the luggage compartment. It also allows the space underneath to be used as a additional compartment for stowing objects which are more fragile or small.
Page 76 74 GETTING TO KNOW YOUR VEHICLE Access To Double Load Compartment 2. Place the desired objects in compartment. To access the double load compartment, proceed as fol- lows: 1. Grip handle and raise platform, holding it with one hand. Load Compartment Load Platform 1 —...
Page 77 GETTING TO KNOW YOUR VEHICLE 75 3. Then reposition the platform correctly in the housings Moving The Load Platform on the side panels and rear crossmember. To move the load platform from lower to upper position, proceed as follows: 1. Grip handle and raise the platform, holding it with one hand.
Page 78 76 GETTING TO KNOW YOUR VEHICLE 2. Position the platform correctly on housing on the side Cargo Area Tie Downs panels. There are two tie downs inside the luggage compartment for attaching cables which can secure the load carried. Two additional tie downs located on the rear crossmember. Raised Position 1 —...
Page 79: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE 77 Cargo hooks are also available on the side panels to fix loads which are not excessively heavy (e.g. bags). Storage Compartment GARAGE DOOR OPENER — IF EQUIPPED Cargo Side Panel Hook Location HomeLink replaces up to three remote controls (hand-held transmitters) that operate devices such as garage door CAUTION! openers, motorized gates, lighting or home security sys-...
Page 80: Before You Begin Programming Homelink
78 GETTING TO KNOW YOUR VEHICLE To erase the channels, place the ignition in the ON/RUN position and push and hold the two outside HomeLink buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: •...
Page 81 GETTING TO KNOW YOUR VEHICLE 79 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. 3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans- mitter button.
Page 82: Programming A Non-Rolling Code
80 GETTING TO KNOW YOUR VEHICLE 6. Return to the vehicle and push the programmed 3. Push and hold the Homelink button you want to HomeLink button twice (holding the button for two program while you push and hold the hand-held trans- seconds each time).
Page 83: Using Homelink
GETTING TO KNOW YOUR VEHICLE 81 which may not be long enough for HomeLink to pick up seconds or longer in rare cases. The garage door may the signal during programming. Similar to this Canadian open and close while you are programming. law, some U.S.
Page 84: Security
82 GETTING TO KNOW YOUR VEHICLE HomeLink will remain active for three minutes. During If you have any problems, or require assistance, please call this time, if the vehicle is locked, HomeLink is disabled. toll-free 1-800-355-3515 Internet HomeLink.com for information or assistance. Security It is advised to erase all channels before you sell or turn in WARNING!
Page 85: General Information
GETTING TO KNOW YOUR VEHICLE 83 General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 86 84 GETTING TO KNOW YOUR VEHICLE Front Center Armrest Storage — If Equipped Lift upward on the armrest to gain access to the storage area. The front center armrest contains a storage compartment. To open the storage compartment push in the upper release The front center armrest can also be lifted up and adjusted latch on the front of the armrest.
Page 87: Cupholders
GETTING TO KNOW YOUR VEHICLE 85 Cupholders For the driver and front passenger, cupholders are located on the floor console between the front seats. Rear Cupholder Power Outlets Passenger Compartment Power Outlet Front Cupholders The power outlet is located on the instrument panel, below For the rear seat passengers their is one cupholder located the climate controls.
Page 88 86 GETTING TO KNOW YOUR VEHICLE Rear Seat Charge Only USB There is also a Rear Seat USB port located on the back of the center console that can be used to charge USB devices. Passenger Compartment Power Outlet NOTE: Do not connect devices with power higher than 180 W to the socket.
Page 89: Roof Luggage Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE 87 Cigar Lighter — If Equipped ROOF LUGGAGE RACK — IF EQUIPPED This is located on the instrument panel, below the climate The crossbars and siderails are designed to carry the controls. To activate the cigar lighter, push and release the weight on vehicles equipped with a luggage rack.
Page 90 88 GETTING TO KNOW YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.
Page 91 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS ▫ Green Indicator Lights ....110 INSTRUMENT CLUSTER ....90 ▫...
Page 92: Instrument Cluster
90 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster...
Page 93: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 91 Instrument Cluster Descriptions WARNING! 1. Speedometer A hot engine cooling system is dangerous. You or • Indicates vehicle speed. others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for 2.
Page 94: Instrument Cluster Display
92 GETTING TO KNOW YOUR INSTRUMENT PANEL 5. Fuel Gauge • The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. • The fuel pump symbol points to the side of the vehicle where the fuel door is located.
Page 95 GETTING TO KNOW YOUR INSTRUMENT PANEL 93 • Down Arrow Button Push and release the down arrow button to scroll downward through the main menu and submenus. • Right Arrow Button Push and release the right arrow button to access the information screens or submenu screens of a main menu item.
Page 96: Change Engine Oil Indicator System
94 GETTING TO KNOW YOUR INSTRUMENT PANEL Change Engine Oil Indicator System Instrument Cluster Display Setup Menu Your vehicle is equipped with an engine oil change indi- The menu comprises a series of functions arranged in a cator system. The “Oil Change Required” message will cycle.
Page 97 GETTING TO KNOW YOUR INSTRUMENT PANEL 95 Speedometer The Trip menu provides the following submenus: • Trip A Push and release the up or down arrow button until the Speedometer Menu item is displayed in the instrument • Trip B cluster display.
Page 98 96 GETTING TO KNOW YOUR INSTRUMENT PANEL Trip B Trip B submenu is divided into two pages that contain the following information. Page Menu item Description Trip B First Page Distance Shows the distance traveled during Trip B. Travel Time Shows the total travel time for Trip B.
Page 99 GETTING TO KNOW YOUR INSTRUMENT PANEL 97 Vehicle Info Service Push and release the up or down arrow button until the The Service submenu will display information about Vehicle Info menu item is displayed in the instrument scheduled maintenance. A pop-up will appear in the cluster display.
Page 100 98 GETTING TO KNOW YOUR INSTRUMENT PANEL The Phone menu has the following submenus The following information is displayed. • Phone: Displays information on phone connectivity. • Distance to the next turn Pushing the OK button on the Steering Wheel will enter •...
Page 101 GETTING TO KNOW YOUR INSTRUMENT PANEL 99 The settings are as follows: Setting Menu Item Setting Name Description Display Backlight Increase or decrease the brightness of the display. Screen Setup Configure display wit the following options: Zone 1: • Temperature (Default) •...
Page 102: Warning Lights And Messages
100 GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Menu Item Setting Name Description Security Park Assist Volume Increase or decrease Park Assist volume. Warning Buzzer Volume Increase or decrease the volume of the warning buzzer. WARNING LIGHTS AND MESSAGES MAR/ON/RUN position. If the light is either not on during startup, stays on, or turns on while driving, have The warning/indicator lights will illuminate in the instru- the system inspected at an authorized dealer as soon as...
Page 103 GETTING TO KNOW YOUR INSTRUMENT PANEL 101 Brake Booster has been detected by the Anti-Lock Brake If brake failure is indicated, immediate repair is necessary. System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has WARNING! been corrected.
Page 104 102 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: This light shows only that the parking brake is — Engine Coolant Temperature Warning Light applied. It does not show the degree of brake application. This light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will —...
Page 105 GETTING TO KNOW YOUR INSTRUMENT PANEL 103 — Electric Power Steering Fault Warning Light — Transmission Fault Warning Light This light will turn on when there’s a fault with the EPS This light will illuminate (together with a message in the (Electric Power Steering) system.
Page 106: Yellow Warning Lights
104 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: If the vehicle is moving and a door is opened, there — Electronic Stability Control (ESC) Warning will also be a single chime. Light — If Equipped The “ESC Indicator Light” in the instrument cluster will —...
Page 107 GETTING TO KNOW YOUR INSTRUMENT PANEL 105 • This light will come on when the vehicle is in an ESC monitors engine and automatic transmission control sys- event. tems. The light will illuminate when the ignition is in the ON/RUN position before engine start. If the bulb does not —...
Page 108 106 GETTING TO KNOW YOUR INSTRUMENT PANEL — Tire Pressure Monitoring System (TPMS) CAUTION! Warning Light Prolonged driving with the Malfunction Indicator The warning light switches on and a message is displayed Light (MIL) on could cause damage to the vehicle to indicate that the tire pressure is lower than the recom- control system.
Page 109 GETTING TO KNOW YOUR INSTRUMENT PANEL 107 on the vehicle placard or tire inflation pressure label, you minute and then remain continuously illuminated. This should determine the proper tire inflation pressure for sequence will continue upon subsequent vehicle start-ups those tires.) as long as the malfunction exists.
Page 110: Yellow Indicator Lights
108 GETTING TO KNOW YOUR INSTRUMENT PANEL The failure relating to these lights could be: CAUTION! (Continued) • One or more blown bulbs Monitoring System (TPMS) sensor to become inoper- • A blown protection fuse able. After using an aftermarket tire sealant it is recommended that you take your vehicle to your au- •...
Page 111 GETTING TO KNOW YOUR INSTRUMENT PANEL 109 — Rear Defrost Light and run the engine at idle or slightly higher until the light turns off. This indicator will illuminate when the rear window defroster is on. The rear window defroster automatically WARNING! turns off after 20 minutes.
Page 112: Green Indicator Lights
110 GETTING TO KNOW YOUR INSTRUMENT PANEL 5°F (-15° C) at the time the engine is shut off as a reminder NOTE: to avoid possible crank delays at the next cold start. • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.
Page 113: Onboard Diagnostic System - Obd Ii
GETTING TO KNOW YOUR INSTRUMENT PANEL 111 high beams are off, pull the lever toward you for a CAUTION! temporary high beam on, flash to pass scenario. • Prolonged driving with the MIL on could cause ONBOARD DIAGNOSTIC SYSTEM — OBD II further damage to the emission control system.
Page 114: Emissions Inspection And Maintenance Programs
112 GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND MAINTENANCE WARNING! PROGRAMS • ONLY an authorized service technician should con- In some localities, it may be a legal requirement to pass an nect equipment to the OBD II connection port in inspection of your vehicle’s emissions control system.
Page 115 GETTING TO KNOW YOUR INSTRUMENT PANEL 113 Your vehicle has a simple ignition actuated test, which you If your OBD II system is not ready, you should see an can use prior to going to the test station. To check if your authorized dealer or repair facility.
Page 117 SAFETY CONTENTS ▫ Child Restraints ..... . .150 SAFETY FEATURES ..... .116 ▫...
Page 118: Safety Features
116 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 119: Electronic Brake Control System
SAFETY the ON/RUN mode, have the light repaired as soon as WARNING! (Continued) possible. • The capabilities of an ABS equipped vehicle must Electronic Brake Control System never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of Your vehicle is equipped with a advanced electronic brake others.
Page 120 118 SAFETY Do not reduce brake pedal pressure unless braking is no axle. If one wheel on a driven axle is spinning faster than longer desired. Once the brake pedal is released, the BAS is the other, the system will apply the brake of the spinning deactivated.
Page 121 SAFETY • Gear selection matches vehicle uphill direction (i.e., In critical situations (braking with different grip condi- vehicle in NEUTRAL (manual transmission), vehicle tions), through the DST function the ESC system controls facing uphill is in forward gear; vehicle backing uphill is the steering to implement an additional torque contribu- in REVERSE gear).
Page 122 120 SAFETY • Oversteer - when the vehicle is turning more than WARNING! (Continued) appropriate for the steering wheel position. the performance of the ESC system. Changes to the • Understeer - when the vehicle is turning less than steering system, suspension, braking system, tire appropriate for the steering wheel position.
Page 123 SAFETY (48 km/h), see an authorized dealer as soon as possible to ESC Operating Modes have the problem diagnosed and corrected. The ESC system has two available operating modes. The ESC Activation/Malfunction Indicator Light (located Full On in the instrument cluster) starts to flash as soon as the tires This is the normal operating mode for ESC.
Page 124 122 SAFETY WARNING! When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in the TCS section) has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced.
Page 125: Auxiliary Driving Systems
SAFETY period. The cold tire inflation pressure must not exceed the WARNING! maximum inflation pressure molded into the tire sidewall. Refer to “Tires – General Information” in “Servicing And Many factors, such as vehicle loading, road conditions, Maintenance” for information on how to properly inflate and driving conditions, influence the chance that the vehicle’s tires.
Page 126 124 SAFETY For example, your vehicle may have a recommended cold CAUTION! (Continued) (parked for more than three hours) tire pressure of 30 psi cause the Tire Pressure Monitoring System (TPMS) (207 kPa). If the ambient temperature is 68°F (20°C) and the sensor to become inoperable.
Page 127 SAFETY • The TPMS is not a substitute for proper tire mainte- The TPMS consists of the following components: nance, and it is the driver’s responsibility to maintain • Receiver Module. correct tire pressure using an accurate tire gauge, even if •...
Page 128 126 SAFETY • The compact spare tire does not have a tire pressure Check TPMS Warnings monitoring sensor. Therefore, the TPMS will not monitor The Tire Pressure Monitoring Telltale Light will flash on the tire pressure in the compact spare tire. and off for 75 seconds and remain on solid when a system •...
Page 129: Occupant Restraint Systems
SAFETY General Information Some of the safety features described in this section may be standard equipment on some models, or may be optional The following regulatory statement applies to all radio equipment on others. If you are not sure, ask your autho- frequency (RF) devices equipped in this vehicle: rized dealer.
Page 130: Seat Belt Systems
128 SAFETY restraints or belt-positioning booster seats should ride WARNING! properly buckled up in a vehicle with a rear seat. • Never place a rear-facing child restraint in front of an 4. Never allow children to slide the shoulder belt behind air bag.
Page 131 SAFETY Enhanced Seat Belt Use Reminder System (BeltAlert) BeltAlert) (the outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is Driver and Passenger BeltAlert (if equipped) unoccupied). The BeltAlert warning sequence starts by BeltAlert is a feature intended to remind the driver blinking the Seat Belt Reminder Light and sounding an and outboard front seat passenger (if equipped with intermittent chime.
Page 132 130 SAFETY pets be restrained in the rear seat (if equipped) in pet WARNING! harnesses or pet carriers that are secured by seat belts, and • Relying on the air bags alone could lead to more cargo is properly stowed. severe injuries in a collision.
Page 133 SAFETY WARNING! (Continued) WARNING! (Continued) position to minimize the risk of severe injury or belt is flat against your body, without twists. If you death in the event of a crash. can’t straighten a seat belt in your vehicle, take it to •...
Page 134 132 SAFETY WARNING! (Continued) likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A frayed or torn seat belt could rip apart in a collision and leave you with no protection.
Page 135 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen. To remove slack in the with minimal, if any slack so that it is comfortable and lap belt portion, pull up on the shoulder belt.
Page 136 134 SAFETY Lap/Shoulder Belt Untwisting Procedure Seat Belts And Pregnant Women Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 137 SAFETY Seat Belt Pretensioner Switchable Automatic Locking Retractor (ALR) The front seat belt system is equipped with pretensioning The seat belts in the passenger seating positions are devices that are designed to remove slack from the seat belt equipped with a Switchable Automatic Locking Retractor in the event of a collision.
Page 138 136 SAFETY ALR is activated, you will hear a clicking sound as the seat How To Engage The Automatic Locking Mode belt retracts. Allow the webbing to retract completely in 1. Buckle the combination lap and shoulder belt. this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occu- 2.
Page 139: Supplemental Restraint Systems (Srs)
SAFETY • Steering Wheel and Column WARNING! (Continued) • Instrument Panel • Do not use the Automatic Locking Mode to restrain • Knee Impact Bolsters occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only •...
Page 140 138 SAFETY The ORC turns on the Air Bag Warning Light in the NOTE: If the speedometer, tachometer, or any engine instrument panel for approximately four to eight seconds related gauges are not working, the Occupant Restraint for a self-check when the ignition switch is in the MAR/ Controller (ORC) may also be disabled.
Page 141 SAFETY WARNING! (Continued) • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 142 140 SAFETY This vehicle may be equipped with a driver and/or front WARNING! (Continued) passenger seat belt buckle switch that detects whether the • Relying on the air bags alone could lead to more driver or front passenger seat belt is buckled. The seat belt severe injuries in a collision.
Page 143 SAFETY Seat belts are necessary for your protection in all collisions, Supplemental Driver Knee Air Bag and also are needed to help keep you in position, away This vehicle is equipped with a Supplemental Driver Knee from an inflating air bag. Air Bag mounted in the instrument panel below the steering column.
Page 144 142 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs).
Page 145 SAFETY positioned in the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag. The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events.
Page 146 144 SAFETY Side Impacts Side Air Bags are a supplement to the seat belt restraint system. Side Air Bags deploy in less time than it takes to The Side Air Bags are designed to activate in certain side blink your eyes. impacts.
Page 147 SAFETY The Side Air Bags will not deploy in all rollover events. The WARNING! rollover sensing system determines if a rollover event may • Side Air Bags need room to inflate. Do not lean be in progress and whether deployment is appropriate. In the event the vehicle experiences a rollover or near rollover against the door or window.
Page 148 146 SAFETY • Supplemental Side Air Bags • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the • Supplemental Knee Air Bags process that generates the non-toxic gas used for air bag •...
Page 149 SAFETY NOTE: Enhanced Accident Response System Reset Procedure • Air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. After the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the igni- •...
Page 150 148 SAFETY Customer Action Customer Will See Customer Action Customer Will See NOTE: Each step MUST BE held for at least two sec- NOTE: Each step MUST BE held for at least two sec- onds onds ACC/ON/RUN. Left turn light is OFF. SOLID.
Page 151 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 152: Child Restraints
150 SAFETY These data can help provide a better understanding of the Child Restraints circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the NOTE: EDR data are recorded by your vehicle only if a United States, and every Canadian province, requires that non-trivial crash situation occurs;...
Page 153 SAFETY There are different sizes and types of restraints for children NOTE: from newborn size to the child almost large enough for an • For additional information, refer to www.safercar.gov/ adult safety belt. Always check the child seat Owner’s parents/index.htm or call: 1–888–327–4236 Manual to make sure you have the correct seat for your •...
Page 154 152 SAFETY Recommended Type Of Child Re- Child Size, Height, Weight Or Age straint Larger Children Children who have outgrown their Belt Positioning Booster Seat and the forward-facing child restraint, but vehicle seat belt, seated in the rear are too small to properly fit the vehi- seat of the vehicle cle’s seat belt Children Too Large for Child...
Page 155 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown • Improper installation can lead to failure of an infant their rear-facing convertible child seat can ride forward- or child restraint. It could come loose in a collision. facing in the vehicle.
Page 156 154 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the Children who are large enough to wear the shoulder belt child is using the lap/shoulder belt, check seat belt fit comfortably, and whose legs are long enough to bend over periodically and make sure the seat belt buckle is latched.
Page 157 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use Any Attachment Method Shown With An “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top Tether Anchor Restraint Tether Anchor...
Page 158 156 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 159 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 160 158 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact.
Page 161 SAFETY Locating The Upper Tether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat, near the floor. Tether Anchorage Routing Position LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the Upper Tether Anchorages...
Page 162 160 SAFETY Center Seat LATCH 1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily WARNING! attach the hooks or connectors to the vehicle anchor- ages. • Do not install a child restraint in the center position 2.
Page 163 SAFETY 6. Test that the child restraint is installed tightly by pulling WARNING! back and forth on the child seat at the belt path. It • Improper installation of a child restraint to the should not move more than 1 inch (25.4 mm) in any direction.
Page 164 162 SAFETY Lap/Shoulder Belt Systems For Installing Child WARNING! Restraints In This Vehicle • Improper installation or failure to properly secure a child restraint can lead to failure of the restraint. The child could be badly injured or killed. • Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint.
Page 165 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 166 164 SAFETY Installing A Child Restraint With A Switchable 3. Slide the latch plate into the buckle until you hear a Automatic Locking Retractor (ALR): “click.” Child restraint systems are designed to be secured in 4. Pull on the webbing to make the lap portion tight vehicle seats by lap belts or the lap belt portion of a against the child seat.
Page 167 SAFETY 9. Test that the child restraint is installed tightly by pulling 1. Look behind the seating position where you plan to back and forth on the child seat at the belt path. It should install the child restraint to find the tether anchorage. not move more than 1 inch (25.4 mm) in any direction.
Page 168: Transporting Pets
166 SAFETY WARNING! (Continued) • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
Page 169: Exhaust Gas
SAFETY WARNING! WARNING! (Continued) • If you are required to drive with the trunk/liftgate/ • Do not leave children or animals inside parked rear doors open, make sure that all windows are vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 170: Safety Checks You Should Make Inside The Vehicle
168 SAFETY Safety Checks You Should Make Inside The Vehicle Defroster Check operation by selecting the defrost mode and place the Seat Belts blower control on high speed. You should be able to feel the air Inspect the seat belt system periodically, checking for cuts, directed against the windshield.
Page 171 SAFETY WARNING! (Continued) WARNING! (Continued) • ONLY use the passenger’s side floor mat on the upside down or turn your floor mat over. Lightly pull to confirm mat is secured using the floor mat fasten- passenger’s side floor area. • ALWAYS make sure objects cannot fall or slide into ers on a regular basis.
Page 172: Periodic Safety Checks You Should Make Outside
170 SAFETY Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under the vehicle after overnight parking for patterns.
Page 173 STARTING AND OPERATING CONTENTS ▫ Operation ......183 STARTING THE ENGINE ....173 ▫...
Page 174 172 STARTING AND OPERATING ▫ Failure Indications ..... .192 TRAILER TOWING ..... .200 ▫...
Page 175: Starting The Engine
STARTING AND OPERATING 173 STARTING THE ENGINE Normal Starting Before starting your vehicle, adjust your seat, adjust both NOTE: Normal starting of either a cold or a warm engine inside and outside mirrors, and fasten your seat belts. is obtained without pumping or pressing the accelerator pedal.
Page 176: Extended Park Starting
174 STARTING AND OPERATING block heater has not been used. An externally powered 3. If the engine fails to start within 10 to 15 seconds, cycle electric engine block heater is available as a factory in- the ignition to the OFF mode, wait five seconds to allow stalled option.
Page 177: After Starting
STARTING AND OPERATING 175 Drive moderately during the first 300 miles (500 km). After CAUTION! the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. To prevent damage to the starter, do not continuously crank the engine for more than 15 seconds at a time.
Page 178: Parking Brake
176 STARTING AND OPERATING PARKING BRAKE When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away Before leaving the vehicle, make sure that the parking from the curb on an uphill grade. The parking brake brake is fully applied.
Page 179: Automatic Transmission
STARTING AND OPERATING 177 CAUTION! WARNING! • It is dangerous to shift out of PARK or NEUTRAL if If the Brake Warning Light remains on with the park- ing brake released, a brake system malfunction is the engine speed is higher than idle speed. If your indicated.
Page 180: Key Ignition Park Interlock
178 STARTING AND OPERATING ON/RUN mode (engine running or not), and the brake WARNING! (Continued) pedal (and the lock button on the gear selector) must be of reasons. A child or others could be seriously or pressed. fatally injured. Children should be warned not to Six-Speed Automatic Transmission touch the parking brake, brake pedal or the trans- mission gear selector.
Page 181 STARTING AND OPERATING 179 Toggling the gear selector forward (-) or rearward (+) while in the Autostick position will manually select the transmis- sion gear. Refer to AutoStick in this section for further information. NOTE: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward) it is probably in the AutoStick (+/-) position (beside the DRIVE position).
Page 182 180 STARTING AND OPERATING When parking on a level surface, you may shift the WARNING! (Continued) transmission into PARK first, and then apply the parking • Your vehicle could move and injure you and others if brake. it is not in PARK. Check by trying to move the gear When parking on a hill, apply the parking brake before selector out of PARK with the brake pedal released.
Page 183 STARTING AND OPERATING 181 The following indicators should be used to ensure that you WARNING! (Continued) have properly engaged the transmission into the PARK • When exiting the vehicle, always remove the ignition position: key from the vehicle and lock the vehicle. •...
Page 184 182 STARTING AND OPERATING When frequent transmission shifting occurs (such as when WARNING! operating the vehicle under heavy loading conditions, in hilly terrain, or traveling into strong head winds), use the Do not coast in NEUTRAL and never turn off the AutoStick shift control (refer to AutoStick in this section for ignition to coast down a hill.
Page 185: Autostick
STARTING AND OPERATING 183 result in transmission damage, Transmission Limp Home NOTE: Even if the transmission can be reset, we recom- Mode is activated. In this mode, the transmission remains mend that you visit an authorized dealer at your earliest in a fixed gear regardless of which forward gear is selected.
Page 186: Mode Selector - If Equipped
184 STARTING AND OPERATING • Transmission shifting will be more noticeable when NOTE: In AutoStick mode, the transmission will only shift up or down when the driver moves the gear selector AutoStick is enabled. rearward (+) or forward (-), except as described below. •...
Page 187: Operating Modes
STARTING AND OPERATING 185 The mode selector always remains in the center position. Traction+ Mode The selected driving mode is indicated by the correspond- This mode is intend to be used on low traction road ing LED light on the selector, and an indication in the surfaces (e.g.
Page 188 186 STARTING AND OPERATING • The Gravity Control system must be used with a gear than 15 mph (25 km/h). After reaching the desired speed, release the accelerator and brake pedals completely. If you that is suitable for the set speed, in order to prevent want to increase/decrease the speed, press the accelerator/ possible engine stalling.
Page 189: Electric Power Steering
STARTING AND OPERATING 187 system completely deactivates. To reactivate it, turn the selector again when the speed is again below 15 mph (25 km/h). • On level ground in urban areas it is advised to deacti- vate the Gravity Control system intervention, since for speeds below 15 mph (25 km/h) in certain conditions, such as when, shifting gears or driving over bumps without using the accelerator pedal, the system might...
Page 190: To Activate
188 STARTING AND OPERATING To Activate To Vary The Speed Setting Push the on/off button to activate the Speed Control. The To Increase Speed cruise indicator light in the instrument cluster display will When the Speed Control is set, you can increase speed by illuminate.
Page 191: To Accelerate For Passing
STARTING AND OPERATING 189 To Decrease Speed To Accelerate For Passing When the Speed Control is set, you can decrease speed by Press the accelerator as you would normally. When the pushing the SET (-) button. pedal is released, the vehicle will return to the set speed. The driver’s preferred units can be selected through the Using Speed Control On Hills Uconnect settings if equipped.
Page 192: To Resume Speed
190 STARTING AND OPERATING To Resume Speed Interaction With Trailer Towing To resume a previously set speed, push the RES button and The Rear Park Assist system is automatically deactivated release. Resume can be used at any speed above 25 mph when a trailer is hitched to the vehicle.
Page 193 STARTING AND OPERATING 191 The tones emitted by the loudspeaker inform the driver indicate the presence of a very close obstacle. A continuous that the vehicle is approaching an obstacle. The pauses tone indicates that the obstacle is less than 12 inches between the tones are directly proportional to the distance (30 cm) away.
Page 194: Failure Indications
192 STARTING AND OPERATING The audible signal is turned off immediately if the distance without reference to the sensor in failure condition. If even increases. The tone cycle remains constant if the distance a single sensor fails, the entire system must be disabled. measured by the inner sensors is constant.
Page 195 STARTING AND OPERATING 193 properly. The Rear Park Assist system might not detect WARNING! (Continued) an obstacle behind the fascia/bumper, or it could pro- not used for towing. Failure to do so can result in vide a false indication that an obstacle is behind the injury or damage to vehicles or obstacles because the fascia/bumper.
Page 196: Parkview Rear Back Up Camera
194 STARTING AND OPERATING If it’s necessary to keep the ball mount and hitch ball If your vehicle is equipped with the Camera Delay feature assembly mounted for a long period, it is possible to filter and it is turned on, the rear camera image will be displayed out the ball mount and hitch ball assembly presence in for up to 10 seconds when the vehicle is shifted out of sensor field of view.
Page 197 STARTING AND OPERATING 195 The following table shows the approximate distances for each zone: Zone Distance To The Rear Of The Vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 3 ft (30 cm - 1 m) Green 3 ft or greater (1 m or greater) WARNING!
Page 198: Adding Fuel
196 STARTING AND OPERATING ADDING FUEL 1. Open the fuel filler door. 2. There is no fuel filler cap. A flapper door inside the pipe seals the system. 3. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refuel- ing.
Page 199 STARTING AND OPERATING 197 Funnel Location For Vehicle With Optional Spare Tire Emergency Fuel Filling Procedure WARNING! • Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. •...
Page 200: Vehicle Loading
198 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) WARNING! (Continued) The GVWR is the total permissible weight of your vehicle • A fire may result if fuel is pumped into a portable including driver, passengers, vehicle, options and cargo. container that is inside of a vehicle.
Page 201 STARTING AND OPERATING 199 Tire Size The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded. The The tire size on the Vehicle Certification Label represents weight on the front and rear of the vehicle should then be the actual tire size on your vehicle.
Page 202: Trailer Towing
200 STARTING AND OPERATING TRAILER TOWING Trailer towing with this vehicle is not recommended. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF The Ground Automatic Transmission Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED...
Page 203: Driving Tips
STARTING AND OPERATING 201 DRIVING TIPS Traction When driving on wet or slushy roads, it is possible for a Driving On Slippery Surfaces wedge of water to build up between the tire and road Information in this section will aid in safe controlled surface.
Page 204 202 STARTING AND OPERATING Flowing/Rising Water WARNING! (Continued) • Driving through standing water limits your vehicle’s WARNING! braking capabilities, which increases stopping dis- Do not drive on or across a road or path where water is tances. Therefore, after driving through standing flowing and/or rising (as in storm run-off).
Page 205 STARTING AND OPERATING 203 CAUTION! (Continued) • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always in- spect your vehicle’s fluids (i.e., engine oil, transmis- sion, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
Page 207 IN CASE OF EMERGENCY CONTENTS ▫ Jacking Instructions .....221 HAZARD WARNING FLASHERS ... .206 BULB REPLACEMENT .
Page 208: Hazard Warning Flashers
206 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS This is an emergency warning system and it should not be used when the vehicle is in motion. Use it when your The Hazard Warning flasher switch is located on the vehicle is disabled and it is creating a safety hazard for instrument panel, below the radio.
Page 209 IN CASE OF EMERGENCY 207 Exterior Bulbs Bulb Number Front Low and High Beam Headlamp HIR2LL Front Turn Signal Lamps WY21W Front Parking LED (See Authorized Dealer) Daytime Running Lamps W21W Front Side Marker Lamps LED (See Authorized Dealer) Rear Tail/Stop Lamps P21/5W Rear Tail Lamp LED (See Authorized Dealer)
Page 210: Replacing Exterior Bulbs
208 IN CASE OF EMERGENCY Replacing Exterior Bulbs 2. Rotate the bulb counterclockwise. Headlamps Low Beam And High Beam 1. Remove the plastic sealing cap from the back of the headlamp housing by turning it counterclockwise. Bulb Removal Procedure Headlamp Sealing Cap Removal...
Page 211 IN CASE OF EMERGENCY 209 3. Remove the bulb when all the tabs are aligned with the 5. Install the new bulb and rotate clockwise to lock in openings in the metal holder. place. 4. Disconnect the electrical connector from the bulb. New Bulb Installation Electrical Connector Removal...
Page 212 210 IN CASE OF EMERGENCY 6. Reinstall the plastic cap. 5. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 6. Reinstall the plastic cap and close the cover on the wheel liner. Front Fog Lamps To replace the front fog lights, see an authorized dealer.
Page 213: Fuses
IN CASE OF EMERGENCY 211 6. Separate the backplate from the tail lamp housing. WARNING! (Continued) 7. Remove the tail, stop, or turn signal bulbs by pushing • Before replacing a fuse, make sure that the ignition is them slightly and turning counterclockwise. off and that all the other services are switched off and/or disengaged.
Page 214: Underhood Fuses
212 IN CASE OF EMERGENCY Also, please be aware that when using power outlets for Underhood Fuses extended periods of time with the engine off may result in The Front Distribution Unit is located on the right side of vehicle battery discharge. the engine compartment, next to the battery.
Page 215 IN CASE OF EMERGENCY 213 Cavity Maxi Fuse Mini Fuse Description 20 Amp Yellow – Ignition Switch 40 Amp Orange – Anti-Lock Brake Pump 70 Amp Tan – Electric Power Steering 30 Amp Green – Radiator Fan - Low Speed 50 Amp Red –...
Page 216: Interior Fuses
214 IN CASE OF EMERGENCY Cavity Maxi Fuse Mini Fuse Description 40 Amp Orange – PTC (Primary) – 15 Amp Blue Front Power Outlet 12V – 7.5 Amp Brown USB Charger Sockets – 7.5 Amp Brown Heated Mirrors Interior Fuses The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver’s side under the instrument panel.
Page 217 IN CASE OF EMERGENCY 215 Fuse Panel Cavity Locations Vehicle Fuse Cavity Mini Fuse Description Number 7.5 Amp Brown Right Low Beam 7.5 Amp Brown Front and Rear Ceiling Lights Trunk and Door Courtesy Lights...
Page 218 216 IN CASE OF EMERGENCY Vehicle Fuse Cavity Mini Fuse Description Number 7.5 Amp Brown Instrument Panel Node 20 Amp Yellow Central Door Locking 15 Amp Blue Diagnostic Socket, Vehicle Radio, Climate Control System, TPMS, Sunroof 7.5 Amp Brown Left High Beam 7.5 Amp Brown Right High Beam 7.5 Amp Brown...
Page 219: Rear Interior Fuses
IN CASE OF EMERGENCY 217 Vehicle Fuse Cavity Mini Fuse Description Number 5 Amp Tan Exterior Mirror, GPS, Electric Mirror, Parking Sen- 5 Amp Tan Climate Control, Seat Regulation 20 Amp Yellow Driver Power Window Rear Interior Fuses The rear interior fuse panel is located on the driver’s side in the rear compartment.
Page 220: Jacking And Tire Changing - If Quipped
218 IN CASE OF EMERGENCY Vehicle Fuse Cavity Mini Fuse Description Number 20 Amp Yellow Hi Fi System 20 Amp Yellow Sun Blind 20 Amp Yellow Sunroof JACKING AND TIRE CHANGING — IF EQUIPPED WARNING! (Continued) • The jack is designed to be used as a tool for changing WARNING! tires only.
Page 221: Jack Location
IN CASE OF EMERGENCY 219 Jack Location Spare Tire Removal/Stowage The spare tire jack is located in the rear cargo area underneath the cargo floor. Spare Tire Location The spare tire is stowed in underneath the rear cargo area Jack Location on the outside of the vehicle.
Page 222: Preparations For Jacking
220 IN CASE OF EMERGENCY 3. When the spare is clear, replace the jack tools. CAUTION! The winch mechanism is designed for use with the jack wrench extension tool only. Use of air wrench or power tool may damage the winch. Preparations For Jacking 1.
Page 223: Jacking Instructions
IN CASE OF EMERGENCY 221 6. Block both the front and rear of the wheel diagonally WARNING! (Continued) opposite the jacking position. For example, if the right • Never start or run the engine with the vehicle on a front wheel is being changed, block the left rear wheel. jack.
Page 224 222 IN CASE OF EMERGENCY 1. Remove the spare tire, jack and wheel bolt wrench. 2. If equipped with aluminum wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pry the center cap off carefully before raising the vehicle. 3.
Page 225 IN CASE OF EMERGENCY 223 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7.
Page 226 224 IN CASE OF EMERGENCY 8. Install the wheel bolts with the threaded end of the 10. Finish tightening the wheel bolts. Push down on the wheel bolt toward the wheel. Lightly tighten the wheel wrench while at the end of the handle for increased bolts.
Page 227: Tire Service Kit
IN CASE OF EMERGENCY 225 TIRE SERVICE KIT Tire punctures of up to 1/4 of an inch (6mm) can be repaired; the kit can be used in all weather conditions. Do If a tire is punctured, you can make a first emergency repair not remove the foreign object from the punctured tire, i.e., using the Tire Service Kit located in the rear storage area screw or nail.
Page 228 226 IN CASE OF EMERGENCY WARNING! (Continued) WARNING! (Continued) – If you are unsure of the condition of the tire or the with plenty of water and drink plenty of water. Do wheel. not induce vomiting! Consult a physician immedi- •...
Page 229: Jump Starting
IN CASE OF EMERGENCY 227 WARNING! Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using Tire Service Kit. Do not exceed 65 mph (110 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you.
Page 230: Preparations For Jump Start
228 IN CASE OF EMERGENCY starting can be dangerous if done improperly, so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack, follow the manufacturer’s operating instructions and precautions. WARNING! Do not attempt jump starting if the battery is frozen. It could rupture or explode and cause personal injury.
Page 231: Jump Starting Procedure
IN CASE OF EMERGENCY 229 Jump Starting Procedure WARNING! (Continued) • Batteries contain sulfuric acid that can burn your WARNING! skin or eyes and generate hydrogen gas which is Failure to follow this jump starting procedure could flammable and explosive. Keep open flames or result in personal injury or property damage due to sparks away from the battery.
Page 232 230 IN CASE OF EMERGENCY Connecting The Jumper Cables 6. Once the engine is started, remove the jumper cables in the reverse sequence. 1. Connect the positive (+) end of the jumper cable to the Disconnecting The Jumper Cables positive (+) post of the discharged vehicle. 1.
Page 233: If Your Engine Overheats
IN CASE OF EMERGENCY 231 • You can also turn the temperature control to maximum If frequent jump starting is required to start your vehicle, you should have the battery and charging system in- heat, the mode control to floor and the blower control to spected at your authorized dealer.
Page 234: Ignition Key Removal Override
232 IN CASE OF EMERGENCY IGNITION KEY REMOVAL OVERRIDE This vehicle is equipped with a Key Ignition Park Interlock which requires the transmission to be in PARK before the ignition switch can be turned to the LOCK/OFF (key removal) position. To remove the key manually, proceed as follows: 1.
Page 235: Gear Selector Override
IN CASE OF EMERGENCY 233 GEAR SELECTOR OVERRIDE If a malfunction occurs and the gear selector cannot be moved out of the PARK position, you can use the following procedure to temporarily move the gear selector: 1. Turn the engine OFF. 2.
Page 236: Freeing A Stuck Vehicle
234 IN CASE OF EMERGENCY 8. Reinstall the gear selector boot. of accelerator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. NOTE: Push the ESC Off switch, to place the Electronic Stability Control (ESC) system in Partial Off mode, before rocking the vehicle.
Page 237: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 235 TOWING A DISABLED VEHICLE CAUTION! (Continued) NOTE: This section describes procedures for towing a engine to idle with the transmission in NEUTRAL disabled vehicle using a commercial towing service. for at least one minute after every five rocking- motion cycles.
Page 238: Enhanced Accident Response System (Ears)
236 IN CASE OF EMERGENCY Proper towing or lifting equipment is required to prevent If the ignition key is unavailable, or the vehicle’s battery is damage to your vehicle. Use only tow bars and other discharged, refer to “Gear Selector Override” in this section equipment designed for this purpose, following equipment for instructions on shifting the transmission out of PARK in manufacturer’s instructions.
Page 239: Event Data Recorder (Edr)
IN CASE OF EMERGENCY 237 EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record data that will assist in understanding how a vehicle’s systems per- formed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle.
Page 241 SERVICING AND MAINTENANCE CONTENTS ▫ Exhaust System ......254 SCHEDULED SERVICING ....241 ▫...
Page 242 240 SERVICING AND MAINTENANCE ▫ Body And Underbody Maintenance ..285 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....282 ▫...
Page 243: Scheduled Servicing
SERVICING AND MAINTENANCE 241 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months, or 350 Your vehicle is equipped with an automatic oil change hours of engine run time: whichever comes first. The 350 indicator system.
Page 244: Maintenance Plan
242 SERVICING AND MAINTENANCE Maintenance Plan At Every Oil Change Interval As Indicated By Oil Change Indicator System: Required Maintenance Intervals • Change oil and filter. Refer to the maintenance plan on the following pages for • Rotate the tires. Rotate at the first sign of irregular the required maintenance intervals.
Page 245 SERVICING AND MAINTENANCE 243 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends and boot seals, and replace if necessary. Inspect the brake linings, parking brake function.
Page 246: Heavy Duty Use Of The Vehicle
244 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Inspect and replace PCV valve if necessary. Replace the timing belt. * The brake fluid change interval is time based only, WARNING! (Continued) mileage intervals do not apply. •...
Page 247: Engine Compartment - 1.4L Turbo
SERVICING AND MAINTENANCE 245 ENGINE COMPARTMENT — 1.4L TURBO 1 — Air Cleaner Filter 4 — Battery 7 — Coolant Pressure Cap 2 — Engine Oil Dipstick 5 — Front Distribution Unit (Fuses) 8 — Coolant Pressure Bottle 3 — Brake Fluid Reservoir 6 —...
Page 248: Adding Washer Fluid
246 SERVICING AND MAINTENANCE Checking the oil while the vehicle is on level ground, and WARNING! approximately five minutes after a fully warmed engine is shut off, will improve the accuracy of the oil level readings. Commercially available windshield washer solvents Maintain the oil level between the range markings on the are flammable.
Page 249: Dealer Service
SERVICING AND MAINTENANCE 247 DEALER SERVICE WARNING! (Continued) An authorized dealer has the qualified service personnel, battery or any other booster source with an output special tools, and equipment to perform all service opera- greater than 12 Volts. Do not allow cable clamps to tions in an expert manner.
Page 250 248 SERVICING AND MAINTENANCE NOTE: Under no circumstances should oil change inter- CAUTION! vals exceed 10,000 miles (16,000 km), twelve months or 350 hours of engine run time, whichever comes first. The 350 Do not use chemical flushes in your engine oil as the hours of engine run or idle time is generally only a concern chemicals can damage your engine.
Page 251: Engine Oil Filter
SERVICING AND MAINTENANCE 249 Synthetic Engine Oils Engine Oil Filter You may use synthetic engine oils provided the recom- The engine oil filter should be replaced with a new filter at mended oil quality requirements are met, and the recom- every engine oil change.
Page 252: Air Conditioner Maintenance
250 SERVICING AND MAINTENANCE WARNING! WARNING! • Use only refrigerants and compressor lubricants ap- The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine proved by the manufacturer for your air conditioning backfire.
Page 253: Body Lubrication
SERVICING AND MAINTENANCE 251 Refrigerant Recovery And Recycling — R–1234yf The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small R–1234yf Air Conditioning Refrigerant is a hydrofluo- amount of a high quality lubricant, such as Mopar Lock roolefin (HFO) that is endorsed by the Environmental Cylinder Lubricant directly into the lock cylinder.
Page 254 252 SERVICING AND MAINTENANCE The wiper blades and wiper arms should be inspected To have a correct activation of strategy, the Service Position periodically, not just when wiper performance problems command (antipanic) must be active for at least half a are experienced.
Page 255 SERVICING AND MAINTENANCE 253 Front Wiper Blade Removal/Installation Rear Wiper Blade Removal/Installation 1. Lift the front wiper arm upward to raise the wiper blade 1. Lift the rear wiper arm upward to raise the wiper blade off of the windshield. off of the liftgate glass.
Page 256: Exhaust System
254 SERVICING AND MAINTENANCE 3. Install the wiper blade pivot pin into the wiper blade WARNING! (Continued) holder at the end of the wiper arm, and firmly push the eventually poison you. To avoid breathing CO, refer wiper blade until it snaps into place. to “Safety Tips”...
Page 257: Cooling System
SERVICING AND MAINTENANCE 255 • Do not idle the engine with any ignition components CAUTION! (Continued) disconnected or removed, such as when diagnostic malfunction could cause the converter to overheat, testing, or for prolonged periods during very rough idle resulting in possible damage to the converter and or malfunctioning operating conditions.
Page 258 256 SERVICING AND MAINTENANCE Coolant Checks Selection Of Coolant Check engine coolant (antifreeze) protection every 12 Refer to “Fluids And Lubricants” in “Technical Specifica- months (before the onset of freezing weather, where appli- tions” for further information. cable). If the engine coolant (antifreeze) is dirty or rusty in NOTE: appearance, the system should be drained, flushed and •...
Page 259 SERVICING AND MAINTENANCE 257 • This vehicle has not been designed for use with propyl- Please review these recommendations for using Organic ene glycol-based engine coolant (antifreeze). Use of Additive Technology (OAT) engine coolant (antifreeze) propylene glycolbased engine coolant (antifreeze) is not that meets the requirements of FCA Material Standard recommended.
Page 260 258 SERVICING AND MAINTENANCE NOTE: The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. • It is the owner’s responsibility to maintain the proper level of protection against freezing according to the WARNING! temperatures occurring in the area where the vehicle is operated.
Page 261 SERVICING AND MAINTENANCE 259 Coolant Level If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be The coolant expansion bottle provides a quick visual safely driven. The vapor will soon dissipate. method for determining that the coolant level is adequate.
Page 262: Brake System
260 SERVICING AND MAINTENANCE unsatisfactory engine coolant (antifreeze) performance, reservoir. With disc brakes, fluid level can be expected to poor gas mileage, and increased emissions. fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level Brake System may be caused by a leak and a checkup may be needed.
Page 263: Automatic Transmission
SERVICING AND MAINTENANCE 261 NOTE: No chemical flushes should be used in any trans- WARNING! (Continued) mission; only the approved lubricant should be used. to boil unexpectedly during hard or prolonged brak- ing, resulting in sudden brake failure. This could CAUTION! result in a collision.
Page 264: Raising The Vehicle
262 SERVICING AND MAINTENANCE Fluid And Filter Changes CAUTION! Under normal operating conditions, the fluid installed at Do not use chemical flushes in your transmission as the factory will provide satisfactory lubrication for the life the chemicals can damage your transmission compo- of the vehicle.
Page 265 SERVICING AND MAINTENANCE 263 Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 266 264 SERVICING AND MAINTENANCE Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 267 SERVICING AND MAINTENANCE 265 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 268 266 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 269 SERVICING AND MAINTENANCE 267 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 270 268 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 271 SERVICING AND MAINTENANCE 269 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 272: Tires - General Information
270 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 273 SERVICING AND MAINTENANCE 271 Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 274 272 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 275 SERVICING AND MAINTENANCE 273 Run Flat Tires — If Equipped WARNING! Run Flat tires allow you the capability to drive 50 miles Fast spinning tires can be dangerous. Forces generated (80 km) at 50 mph (80 km/h) after a rapid loss of inflation by excessive wheel speeds may cause tire damage or pressure.
Page 276 274 SERVICING AND MAINTENANCE Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 277 SERVICING AND MAINTENANCE 275 Keep dismounted tires in a cool, dry place with as little It is recommended you contact an authorized tire dealer or exposure to light as possible. Protect tires from contact with original equipment dealer with any questions you may oil, grease, and gasoline.
Page 278: Tire Types
276 SERVICING AND MAINTENANCE Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 279: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 277 Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 280 278 SERVICING AND MAINTENANCE spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 281: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 279 use spare wheel. This label contains the driving limitations WARNING! for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Compact and Collapsible spares are for temporary Installation of this limited use spare tire affects vehicle emergency use only.
Page 282 280 SERVICING AND MAINTENANCE and to prevent corrosion. Wash wheels with the same soap When cleaning extremely dirty wheels including excessive solution recommended for the body of the vehicle and brake dust, care must be taken in the selection of tire and remember to always wash when the surfaces are not hot to wheel cleaning chemicals and equipment to prevent dam- the touch.
Page 283: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 281 Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 284: Tire Rotation Recommendations
282 SERVICING AND MAINTENANCE The suggested rotation method is the “forward cross” CAUTION! (Continued) shown in the following diagram. This rotation pattern does • Observe the traction device manufacturer’s instruc- not apply to some directional tires that must not be tions on the method of installation, operating speed, reversed.
Page 285: Treadwear
SERVICING AND MAINTENANCE 283 All passenger vehicle tires must conform to Federal WARNING! safety requirements in addition to these grades. The traction grade assigned to this tire is based on Treadwear straight-ahead braking traction tests, and does not The Treadwear grade is a comparative rating, based on include acceleration, cornering, hydroplaning, or the wear rate of the tire when tested under controlled peak traction characteristics.
Page 286: Vehicle Storage
284 SERVICING AND MAINTENANCE BODYWORK WARNING! Protection From Atmospheric Agents The temperature grade for this tire is established for Vehicle body care requirements vary according to geo- a tire that is properly inflated and not overloaded. graphic locations and usage. Chemicals that make roads Excessive speed, under-inflation, or excessive load- passable in snow and ice and those that are sprayed on ing, either separately or in combination, can cause...
Page 287: Body And Underbody Maintenance
SERVICING AND MAINTENANCE 285 • Insects, tree sap and tar. Preserving The Bodywork • Salt in the air near seacoast localities. Washing • Atmospheric fallout/industrial pollutants. • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar Car Wash, or a mild car wash Body And Underbody Maintenance soap, and rinse the panels completely with clear water.
Page 288: Interiors
286 SERVICING AND MAINTENANCE Special Care INTERIORS • If you drive on salted or dusty roads or if you drive near Seats And Fabric Parts the ocean, hose off the undercarriage at least once a Use Mopar Total Clean to clean fabric upholstery and month.
Page 289: Plastic And Coated Parts
SERVICING AND MAINTENANCE 287 Cleaning Plastic Instrument Cluster Lenses WARNING! The lenses in front of the instruments in this vehicle are A frayed or torn belt could rip apart in a collision and molded in clear plastic. When cleaning the lenses, care leave you with no protection.
Page 290: Glass Surfaces
288 SERVICING AND MAINTENANCE Your leather upholstery can be best preserved by regular Glass Surfaces cleaning with a damp soft cloth. Small particles of dirt can All glass surfaces should be cleaned on a regular basis with act as an abrasive and damage the leather upholstery and Mopar Glass Cleaner, or any commercial household-type should be removed promptly with a damp cloth.
Page 291 TECHNICAL SPECIFICATIONS CONTENTS ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..294 IDENTIFICATION DATA....290 ▫ Vehicle Identification Number ... . .290 ▫...
Page 292: Identification Data
290 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears engraved on the right front floor pan under the passenger seat, on an adhesive label applied to the right door opening on the B-Pillar, on the vehicle registration and title.
Page 293: Wheel And Tire Torque Specifications
TECHNICAL SPECIFICATIONS 291 In the event power assist is lost for any reason (i.e., **Use only your authorized dealer recommended lug nuts/ repeated brake applications with the engine off) the brakes bolts and clean or remove any dirt or oil before tightening. will still function.
Page 294: Fuel Requirements
292 TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS 1.4L Turbo This engine is designed to meet all emis- sion regulations, provide satisfactory fuel economy and performance when using high-quality unleaded “Regular” gasoline having a posted octane number of 87 as specified by the (R+M)/2 method.
Page 295: Reformulated Gasoline
TECHNICAL SPECIFICATIONS 293 Reformulated Gasoline gasoline is recommended. Visit www.toptiergas.com for a list of TOP TIER Detergent Gasoline Retailers. Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Indiscriminate use of fuel system cleaning agents should be Reformulated gasoline contains oxygenates and are specifi- avoided.
Page 296: Do Not Use E-85 In Non-Flex Fuel Vehicles
294 TECHNICAL SPECIFICATIONS Problems that result from using gasoline containing more CNG And LP Fuel System Modifications than 15% ethanol (E-15) or gasoline containing methanol Modifications that allow the engine to run on compressed are not the responsibility of the manufacturer and may natural gas (CNG) or liquid propane (LP) may result in void or not be covered under New Vehicle Limited War- damage to the engine, emissions, and fuel system compo-...
Page 297: Fuel System Cautions
TECHNICAL SPECIFICATIONS 295 Fuel System Cautions NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. CAUTION! Carbon Monoxide Warnings Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gasoline is prohibited by Federal WARNING! law.
Page 298: Fluid Capacities
296 TECHNICAL SPECIFICATIONS FLUID CAPACITIES U.S. Metric Fuel (Approximate) 12.7 Gallons 48.1 Liters Engine Oil with Filter 1.4L Turbo Engine 4 Quarts 3.8 Liters Cooling System 1.4L Turbo Engine (Mopar 6.1 Quarts 5.8 Liters Antifreeze/Engine Coolant 10 Year/ 150,000 Mile Formula). FLUIDS AND LUBRICANTS Engine Component...
Page 299 TECHNICAL SPECIFICATIONS 297 Component Fluid, Lubricant, or Genuine Part Engine Oil Filter – 1.4L Turbo Engine We recommend you use Mopar Engine Oil Filter. Spark Plugs – 1.4L Turbo Engine We recommend you use Mopar Spark Plugs. Fuel Selection – 1.4L Turbo Engine 91 Octane Recommended –...
Page 300: Chassis
298 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar AW-1 Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake Master Cylinder We recommend you use Mopar DOT 4. If DOT 4 brake fluid is not available, then DOT 3 is acceptable.
Page 301 MULTIMEDIA CONTENTS UCONNECT SYSTEMS ....300 UCONNECT VOICE RECOGNITION QUICK TIPS ....... . .317 DRAG &...
Page 302: Uconnect Systems
300 MULTIMEDIA UCONNECT SYSTEMS For detailed information about your Uconnect system, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. DRAG & DROP MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 303: Cybersecurity
MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 304: Uconnect Settings
302 MULTIMEDIA NOTE: access programmable features that may be equipped such as Language, Display, Units, Voice, Clock & Date, Safety/ • FCA US or your dealer may contact you directly regard- Driving Assistance, Lights, Doors & Locks, Engine Off ing software updates. Options, Phone, SiriusXM Setup, Restore Settings to De- •...
Page 305 MULTIMEDIA Language After pressing the “Language” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Language English Français Español Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Auto...
Page 306 304 MULTIMEDIA Setting Name Selectable Options Touchscreen Beep Display Trip B • Custom Units • Units When “Custom” is selected, you may select each unit of measure independently displayed in the instrument cluster When in this display, you may select to have the instru- display, and navigation system.
Page 307 MULTIMEDIA Clock & Date After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With NOTE: This feature will allow you to automatically have the radio set the time. To change the Sync Time setting, press the “Sync Time with Nav”...
Page 308 306 MULTIMEDIA Setting Name Selectable Options Set Date (MM/DD/YY) NOTE: This feature allows you to set the date, month, and year using the plus and minus buttons. Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 309 MULTIMEDIA Setting Name Selectable Options Cornering Lights NOTE: When this feature is selected, if the steering wheel rotation angle is large or the turn signal indicators are on, a light (incorporated in the fog light) will turn on, on the relevant side to improve visibility at night. Doors &...
Page 310 308 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon Arrow Buttons NOTE: When in this display you may adjust the Balance and Fade settings. Equalizer –...
Page 311 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Horn With Remote Start Auto-On Driver Heated/Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 312 310 MULTIMEDIA Phone WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. After pressing the “Phone”...
Page 313 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music chan- nel using one of the twelve presets, so you can enjoy the complete song.
Page 314 312 MULTIMEDIA Setting Name Selectable Options Subscription Information Subscription Info NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 315: Steering Wheel Audio Controls
MULTIMEDIA Clear Personal Data After pressing the “Clear Personal Data Settings” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Clear Personal Data NOTE: When this feature is selected, it will remove personal data including Bluetooth devices and presets. Steering Wheel Audio Controls The remote sound system controls are located at the rear of the steering wheel.
Page 316: Radio Operation
314 MULTIMEDIA mode of the sound system. Pushing the top of the rocker Player Operation switch will increase the volume, and pushing the bottom of Pushing the top of the switch once will go to the next track the rocker switch will decrease the volume. on the Player.
Page 317: Radio Operation And Mobile Phones
MULTIMEDIA not satisfactorily “clear” by the repositioning of the an- tenna, it is recommended that the radio volume be turned down or off during mobile phone operation when not using Uconnect (if equipped). Regulatory And Safety Information USA/CANADA Exposure to Radio Frequency Radiation The radiated output power of the internal wireless radio is far below the FCC and IC radio frequency exposure limits.
Page 318 316 MULTIMEDIA environments, such as aboard airplanes. If you are unsure NOTE: of restrictions, you are encouraged to ask for authorization • This equipment has been tested and found to comply before turning on the wireless radio. with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 319: Uconnect Voice Recognition Quick
MULTIMEDIA UCONNECT VOICE RECOGNITION QUICK TIPS 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after the Introducing Uconnect beep, then say your Voice Command. Start using Uconnect Voice Recognition with these helpful 5.
Page 320: Basic Voice Commands
318 MULTIMEDIA Basic Voice Commands Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touch- The basic Voice Commands below can be given at any screen. point while using your Uconnect system. Radio Push the VR button .
Page 321: Media
MULTIMEDIA TIP: At any time, if you are not sure of what to say or want Media to learn a Voice Command, push the VR button and say Uconnect offers connections via USB, Bluetooth and auxil- “ Help.” The system provides you with a list of com- iary ports (If Equipped).
Page 322: Phone
320 MULTIMEDIA TIP: Press the Browse button on the touchscreen to see all Phone of the music on your USB device. Your Voice Command Making and answering hands-free phone calls is easy with must match exactly how the artist, album, song and genre Uconnect.
Page 323: Navigation
MULTIMEDIA 1. To enter a destination, push the VR button . After the beep, say: • For the 4 Uconnect System, say: “ Enter state.” • For the 4 NAV Uconnect System, say: “ Find address 800 Chrysler Drive Auburn Hills, Michigan.” 2.
Page 324: General Information
322 MULTIMEDIA General Information Additional Information The following regulatory statement applies to all Radio © 2017 FCA US LLC. All rights reserved. Mopar and Frequency (RF) devices equipped in this vehicle: Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a This device complies with Part 15 of the FCC Rules and trademark of Google Inc.
Page 325: Cd/Dvd Disc Maintenance
MULTIMEDIA CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
Page 327 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......326 Impaired (TDD/TTY) .
Page 328: Suggestions For Obtaining Service For Your Vehicle
326 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 329: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 327 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 330: Service Contract
328 CUSTOMER ASSISTANCE to a TDD or a conventional teletypewriter (TTY) in the responsible for any service contract other than the manu- United States, can communicate with the manufacturer by facturer’s service contract. If you purchased a service dialing 1-800-380-CHRY. contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Canadian residents with hearing difficulties that require...
Page 331: Warranty Information
CUSTOMER ASSISTANCE 329 If NHTSA receives similar complaints, it may open an WARNING! (Continued) investigation, and if it finds that a safety defect exists in California to cause cancer and birth defects, or other a group of vehicles, it may order a recall and remedy reproductive harm.
Page 332: Publication Order Forms
330 CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS Owner’s Manuals To order the following manuals, you may use either the These Owner’s Manuals have been prepared with the website or the phone numbers listed below. Visa, Master- assistance of service and engineering specialists to acquaint card, American Express, and Discover orders are accepted.
Page 333 INDEX...
Page 334 332 INDEX About Your Brakes ..... . .290 Air Pressure, Tires......271 Adding Engine Coolant (Antifreeze) .
Page 335 INDEX 333 Battery ......103, 246 Carbon Monoxide Warning ....167, 295 Charging System Light .
Page 336 334 INDEX Cleaning Customer Assistance ..... .326 Wheels ......279 Climate Control .
Page 337 INDEX 335 Electronic Stability Control (ESC) ... . .119 Overheating ......231 Electronic Throttle Control Warning Light .
Page 338 336 INDEX Fluids And Lubricants .....296 Gear Ranges ......179 Fog Lights .
Page 339 INDEX 337 Instrument Panel Lens Cleaning ....287 Latches .......170 Interior And Instrument Lights .
Page 340 338 INDEX Service ......206 Mirrors ....... .38 Tire Pressure Monitoring (TPMS) .
Page 341 INDEX 339 Identification Logo .....248 Seats ....... .31 Materials Added To .
Page 342 340 INDEX Remote Starting Seat Belt Reminder .....129 Uconnect Customer Programmable Features . . .309 Seat Belt Maintenance .....286 Uconnect Settings .
Page 343 INDEX 341 Ventilated ......27 Steering ....... .37 Security Alarm .
Page 344 342 INDEX Inflation Pressures .....271 Transmission Jacking ......218, 262 Automatic .
Page 345 INDEX 343 Vanity Mirrors ......42 Window Fogging ......62 Vehicle Identification Number (VIN) .
Page 346 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Fiat 500L2018 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Technical Specifications

Multimedia

Customer Assistance

Quick Links

Chapters

Related Manuals for Fiat 500L2018

Summary of Contents for Fiat 500L2018