Page 1
• Warranty Card (1) Battery life * Some signals cannot be learned by the Approx. 5 months (a Sony TV turned on/off Remote Commander, even though the signals up to approx. 300 times per day) comply with these specifications. Dimensions ×...
RM-AX4000 TABLE OF CONTENTS Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 °C during repairing. GENERAL ..............3 • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
RM-AX4000 SECTION 1 GENERAL This section is extracted from instruction manual. Location and function qs Display title Shows the title of the LCD Display. If of controls a page number such as “/1” appears, multiple pages are available. If you press the number, next page displays.
Page 4
RM-AX4000 Setting the clock Next, press the g button. The day of the week is set. When you install batteries the first time, “12” (hour) “AM” and “SET” flash. the Remote Commander enters clock LEARN setup mode. CLOCK “DS_TIME” appears as the Display title.
Page 5
RM-AX4000 LEARN CLOCK Press “CLOCK” on the Label keys. CLOCK STD_TIME The setting display for clock appears. Notes • If you press the g button, the minute is set and the setting mode returns to step 3. LEARN CLOCK • If you press the G button, the minute is set and the setting mode r eturns to step 4.
Page 6
RM-AX4000 To change the display to Press the STD_TIME or DS_TIME the daylight savings time key. (summer time) indication You can select the standard time (STD_TIME) or summer time (DS_TIME). To change this setting, perform the STD_TIME is 1 hour behind the following procedure.
RM-AX4000 SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. CASE (LOWER) 5 two screws 4 screw (+P 2 × 6) (+P 2 × 6) 3 two screws (+P 2 × 6) 7 case (lower)
RM-AX4000 SECTION 3 TEST MODE Setting the Test Mode Pattern 1 Install the battery while holding down the VOLUME+ and Displays the title and character keys CHANNEL+ buttons, and turn on the power. The display becomes as follows. * The backlight is always on.
Page 10
RM-AX4000 5. Backlight adjustment It is set to LEVEL 5 by default. CHANNEL+ button: Turns on the backlight at LEVEL 15. CHANNEL– button: Turns on the backlight at LEVEL 1. MUTING button: Turns off the backlight. OK button: Proceeds to the key test.
RM-AX4000 SECTION 4 DIAGRAMS Note on Schematic Diagrams: Note on Printed Wiring Boards: • IC Block Diagram • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or • Y : parts extracted from the conductor side.
RM-AX4000 4-2. PRINTED WIRING BOARD – MAIN BOARD – • :Uses unleaded solder. IC1 (SYSTEM CONTROLLER) can not be replaced individually. Replace it with MAIN board assembly for service. LCD UNIT MAIN BOARD (SIDE A) MAIN BOARD (SIDE B) SEND...
RM-AX4000 • See page 11 for Waveforms. • See page 11 for IC Block Diagram. 4-3. SCHEMATIC DIAGRAM – MAIN BOARD – IC1 (SYSTEM CONTROLLER) can not be replaced individually. Replace it with MAIN board assembly for service. LED5 RECEIVED...
Page 15
RM-AX4000 • IC Pin Function Description MAIN BOARD IC1 uPD78F0547GC(T)-UBT-A (SYSTEM CONTROLLER) Pin No. Pin Name Description P120/REF_I External Low Voltage detective signal input P47/LCD_DB7 LCD data output P46/LCD_DB6 LCD data output P45/LCD_DB5 LCD data output P44/LCD_DB4 LCD data output...
Page 16
RM-AX4000 Pin No. Pin Name Description P16/IR O IR signal output P15/BZ_O BUZZER out P14/FLASH_I RXD6 FLASH_WRITE signal input P13/FLASH_O TXD6 FLASH_WRITE signal output P12/SI_O USB SI signal output P11/USBRX_I USB SO signal input P10/USBTX_O USB SK signal output USB RTS (connected to +5V)
RM-AX4000 SECTION 5 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference number may have some difference from the original in the exploded views are not supplied. one. • Items marked “*” are not stocked since they are seldom required for routine service.
RM-AX4000 SECTION 6 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, uH: µH parts list may be different from the parts please include the board name. specified in the diagrams or the components •...
Page 19
RM-AX4000 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < LED > 1-218-895-11 METAL CHIP 100K 0.50% 1/10W 1-216-829-11 METAL CHIP 4.7K 1/10W LED1 8-719-059-09 DIODE SID307BR LED2 8-719-059-09 DIODE SID307BR 1-216-829-11 METAL CHIP 4.7K...
RM-AX4000 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...
Need help?
Do you have a question about the RM-AX4000 and is the answer not in the manual?
Questions and answers