Temperature Mode - Electrolux ICON E24RD50QS User And Care Manual

Operation
........................................... gOml/O =BmmBJ!
' iii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i!_!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_
iiiiiiiiiiiiiiiiiiii!}iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!}il
ii ! !iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i
llll!}l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_l_llil_i
Adjusting the temperature:
To set or check the set-point temperature
(with the control out of sleep mode),
press the "-" or "+" keypads. "SET" will
be indicated on the user interface panel
and the current set-point temperature will
display and flash. Subsequent presses
of the "-" or "+" keypads will adjust the
temperature colder or warmer respectively.
When you have reached your desired
set-point temperature, press the "On/Off"
keypad to accept, or do nothing and the
"Set" mode will time-out in 10 seconds
........................................................................ accepting the displayed temperature as
thenewset-point,
'"'"'"'"'"'" ............................................... The available set-point temperature range
.............................................................. for your appliance is 34°F (1.1 °C) to
.......................................................... 42°F (5.6°C). If you attempt to adjust the
,,,,,,,,,,,,,,,,,,,,,,,,,,,, ........................... temperature outside of this range you will
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, ..................... receive an audible notification.
................................................. Ily I g y p
When initia oadin our roductwith
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, warm contents, it may take up to 48 hours
for the storage compartment temperature
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii tostabi,ze.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii When making temperature set-point
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii changes, it maytake up to 24 hours for
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii the stored contents to stabilize at your
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii newset-pOinttemperature'
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Factorsthat affectthe storage
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii oompa mentstab,ized*emperature:
_ o Changes to temperature setting.
Room temperature changes.
Temperature of stored contents,
Loading warm contents.
Temperature mode:
The temperature mode is preset from the
factory in Fahrenheit (°F) but you have the
option to change it to Centigrade (°C). To
change the mode, press and hold the "-"
keypad, while pressing the "+" keypad,
then release the "-" keypad.
The temperature will now be displayed in
Centigrade (°C).
Repeat the procedure to change the
temperature mode back to Fahrenheit (°F).
Control lock:
The control panel can be locked to avoid
unintentional changes, To lock the control,
press and hold the "Lock" keypad until the
display reads "Loc". The lock icon will flash
3 times and then continuously illuminate.
When the control panel is locked, only the
Lock keypad, System Status OK indicator,
and the Alarm indicator are active. To
unlock the control panel, repeat this
instruction until the display reads "nLc",
Cold content load will delay the
change to a warmer set-point
temperature,
- Warm content load will delay
the change to a colder set-point
temperature.
Usage, (number and duration of the
drawer openings).