Advertisement
Available languages
Available languages
Connections
English
Connecting the units
Blue/White
Head unit
Control signal is output through blue/white cable
(sold separately)
when Pioneer head unit is turned on. Connect it
to the vehicle's auto-antenna relay control
terminal (max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
3 m (9 ft. 10 in.)
IP-BUS cable
To IP-BUS input
(supplied)
(blue)
Black
This unit
IP-BUS cable
Antenna jack
Blue
Multi-CD player
(sold separately)
3 m (9 ft. 10 in.)
Antenna cable
(supplied)
Car antenna cable (form vehicle's antenna)
Connect the car antenna cable to this unit's
antenna input. It is not necessary to connect to
head unit's antenna input.
If you use this unit with a navigation system that
can receive traffic information from the built-in
FM tuner, connect the car antenna cable to both
Fuse (2 A)
Yellow
this unit and the navigation system with an
Connect to the constant
antenna splitter or to a separate antenna.
12 V supply terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
Installation
English
Connections
• Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring or
other important parts.
Important
• If this unit installed in the passenger compartment,
• Use this unit in a vehicle of a 12-volt battery and
anchor it securely so it does not break free while
negative grounding.
the vehicle is moving, and cause injury or an
• To prevent short-circuit, overheating or
accident.
malfunction, be sure to follow the directions
• If this unit is installed under a front seat, make
below.
sure it does not obstruct seat movement. Route
— Disconnect the negative terminal of the battery
all leads and cords carefully around the sliding
before installation.
mechanism so they do not caught or pinched in
— Secure the wiring with cable clamps or adhesive
the mechanism and cause a short-circuit.
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
— Place all cables away from moving parts, such as
Mounting with hook and loop fasteners
gear shift and seat rails.
Thoroughly wipe off the surface before affixing
— Place all cables away from hot places, such as
the hook and loop fasteners.
near the heater outlet.
— Do not pass the yellow cable through a hole into
• If the hook fasteners adhere to the car mat
the engine compartment to connect to a battery.
directly, you may install this unit without using the
— Do not shorten any cables.
loop fasteners.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
Mount this unit using the hook and
equipment. Current capacity of the cable is
loop fasteners.
limited.
— Use a fuse of the rating prescribed.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
This unit
• Place antenna cable as far away as possible from
the other cables to prevent noise.
• Black cable is ground. This cable and other
Hook fastener
product's ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
Loop fastener
result if they are accidentally detached.
Installing this unit
Car mat or chassis
Important
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
• Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result of a
sudden stop.
• When mounting this unit, make sure none of
the leads are trapped between this unit and the
surrounding metalwork or fittings.
• Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
Additional Information
English
Specifications
General
Rated power source ............ 14.4 V DC
(allowable voltage range:
10.8 V to 15.1 V DC)
Grounding system ............... Negative type
Max. current consumption
..................................... 2.0 A
Dimensions (W × H × D) ..... 121 mm × 30 mm × 79 mm
(4-3/4 in. × 1-1/8 in. × 3-1/8 in.)
Weight ............................... 350 g (0.8 lbs)
Analog FM tuner
Frequency range ................. 87.9 MHz to 107.9 MHz
Usable sensitivity ................ 14 dBf (0.7 μV/75 W, mono,
S/N: 30 dB)
Signal-to-noise ratio ............ 61 dB (IHF-A network)
Digital FM tuner
Frequency range ................ 87.9 MHz to 107.9 MHz
Signal-to-noise ratio ............ 70 dB (IHF-A network)
Frequency response............. 30 Hz to 15 000 Hz (±3 dB)
Stereo separation ................ 70 dB (at 1 kHz)
Analog AM tuner
Frequency range ................. 530 kHz to 1 710 kHz (10 kHz)
Usable sensitivity ................. 50 μV (S/N: 20 dB)
Signal-to-noise rati .............. 58 dB (IHF-A network)
Digital AM tuner
Frequency range ................. 530 kHz to 1 710 kHz (10 kHz)
Signal-to-noise ratio ............ 70 dB (IHF-A network)
Frequency response............. 40 Hz to 15 000 Hz (±3 dB)
Stereo separation ................ 70 dB (at 1 kHz)
Note
Specifications and the design are subject to
possible modifications without notice due to
improvements.
Advertisement
