Initial Settings - Pioneer DEH-P8300UB Owner's Manual

Operating this unit
SLA (source level adjustment)
SLA (Source Level Adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! When selecting FM as the source, you cannot
switch to SLA.
! Settings are based on the FM volume level,
which remains unchanged.
! The AM volume level can also be adjusted with
this function.
1 Push M.C. up or down to adjust the source vol-
ume.
Adjustment range: +4 to –4

Initial Settings

1
1 Function display
! Shows the function status.
1 Press and hold SRC/OFF until the unit
turns off.
2 Press M.C. and hold until the initial set-
ting menu appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
Language select (multi-language)
For your convenience, this unit equips multiple
language display. You can select the language
best suited to your first language.
1 Press M.C. to select the language.
English—Français—Español
Calendar (setting the date)
1 Push M.C. left or right to select the segment of
the calendar display you wish to set.
Year—Day—Month
2 Push M.C. up or down to set the date.
Clock (setting the clock)
1 Push M.C. left or right to select the segment of
the clock display you wish to set.
Hour—Minute
2 Push M.C. up or down to put a clock right.
! You can match the clock to a time signal by
pressing M.C.
! If 00 to 29, the minutes are rounded down.
(e.g., 10:18 becomes 10:00.)
! If 30 to 59, the minutes are rounded up. (e.
g., 10:36 becomes 11:00.)
EngineTime alert (elapsed time display setting)
This setting allows you to measure the length of
time that elapses from when the machine is
turned on and display the amount of elapsed time
per set period.
Also, you will hear alarm.
1 Press M.C. to select your favorite setting.
OFF—15Minutes—30Minutes
USB plug&play (plug and play)
Operating this unit
This setting allows you to switch your source to
USB/iPod/Pandora automatically.
1 Press M.C. to turn the plug and play function
on or off.
! ON – When a USB storage device/iPod is
connected, depending on the type of de-
vice, the source is automatically switched
to USB/iPod/Pandora when you turn on
the engine. If you disconnect your USB
storage device/iPod, this unit's source is
turned off.
! OFF – When USB storage device/iPod is
connected, the source is not switched to
USB/iPod/Pandora automatically. Please
change the source to USB/iPod/Pandora
manually.
Warning tone (warning tone setting)
If the front panel is not detached from the head
unit within four seconds of turning off the ignition,
a warning tone sounds. You can turn off the warn-
ing tone.
1 Press M.C. to turn the warning tone on or off.
AUX1/AUX2 (auxiliary input setting)
Activate this setting when using an auxiliary de-
vice connected to this unit.
1 Press M.C. to turn auxiliary setting on or off.
Dimmer (dimmer setting)
To prevent the display from being too bright at
night, the display is automatically dimmed when
the car's headlights are turned on. You can turn
the dimmer on or off.
1 Press M.C. to turn dimmer on or off.
Brightness (display brightness setting)
1 Push M.C. left or right to adjust the brightness
level.
0 to 15 is displayed as the level is increased or
decreased.
! When dimmer is functioning, the bright-
ness level can be adjusted 0 to 10.
S/W control (rear output and subwoofer setting)
This unit's rear output (rear speaker leads output
and RCA rear output) can be used for full-range
speaker (Rear SP :F.Range) or subwoofer (Rear
SP :S/W) connection. If you switch the rear output
setting to Rear SP :S/W, you can connect a rear
speaker lead directly to a subwoofer without using
an auxiliary amp.
1 Press M.C. to switch the rear output setting.
! When no subwoofer is connected to the
rear output, select Rear SP :F.Range (full-
range speaker).
! When a subwoofer is connected to the rear
output, select Rear SP :S/W (subwoofer).
! Even if you change this setting, there will be
no output unless you turn the subwoofer out-
put on (refer to Sub W.1 (subwoofer on/off set-
ting) on the previous page).
! If you change this setting, subwoofer output in
the audio menu will return to the factory set-
tings.
! Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this set-
ting.
Demonstration (demo display setting)
1 Press M.C. to turn the demo display on or off.
! You can also turn on or off feature demo by
pressing DISP while this unit is turned off.
For more details, refer to Demo mode on
page 3.
Reverse mode (reverse mode setting)
1 Press M.C. to turn the reverse mode on or off.
! You can also turn on or off reverse mode by
pressing BAND while this unit is turned
off. For more details, refer to Reverse mode
on page 3.
Ever-scroll (scroll mode setting)
Section
02
11
En