Table of Contents
Advertisement
Quick Links
X458
MODEL V1101C SYSTEM 10™
MULTIFUNCTION CONTROL
Copyright © 2000 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
WARNING: TO PREVENT RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com
Vicon part number 8006-8458-02-00
Section 9 Rev 700
Advertisement
Table of Contents
Related Manuals for Vicon V1101C
Summary of Contents for Vicon V1101C
- Page 1 Copyright © 2000 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. WARNING: TO PREVENT RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788...
-
Page 5: Table Of Contents
For All Adjustments ..........................5 Output Voltage Selection........................5 Housing Controls ..........................6 Operation............................7 Power ..............................7 Pan-and-Tilt............................7 Lens ..............................7 Maintenance ............................8 Shipping Instructions........................8 Technical Information ........................9 Contents • • i X458 Rev 700 V1101C... - Page 7 Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory recommended by Vicon should be used.
- Page 8 Vicon or that have the same characteristics as the original part. Unauthorized 17. Object and Liquid Entry - Never push objects of...
-
Page 9: Introduction
Introduction The information in this manual covers the installation, operation and maintenance of the V1101C System 10 Multifunction Control. This unit should only be installed by a qualified technician using approved materials in accordance with national, state and local codes. Read these instructions through completely before attempting installation. - Page 10 Notes 2 • • Introduction X458 Rev 700 V1101C...
-
Page 11: Installation
Installation Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition as it left the factory. Inspection For Visible Damage Immediately inspect the cartons upon delivery. Make a note of any visible damage on all copies of the carrier’s freight bill. -
Page 12: Wiring The Motorized Lens
Prepare the interconnecting cable assembly for the housing according to Figure 4. Select the wire size from Table 2. Table 2 Housing Operating Distances Cable Size Maximum Distance to Control (AWG) ft (m) 470 (140) 750 (220) 1200 (370) 1800 (55) 4 • • Installation X458 Rev 700 V1101C... -
Page 13: Testing And Adjustment Procedures
1. After attaching the mating connector to the lens cable according to Figure 3, plug the lens cable into the LENS connector on the back of the unit (see Figure 1). 2. Plug the AC power cord into the appropriate power source. Vicon strongly recommends the use of line conditioners, voltage regulators, and uninterruptible power supply (UPS) systems. -
Page 14: Housing Controls
To obtain the best washing action, turn the wiper on first. Operate the momentary washer switch for about two seconds for each wash. The water container holds enough solution for approximately 70 two-second washes. 6 • • Installation X458 Rev 700 V1101C... -
Page 15: Operation
Power When the AC power cord is plugged into the appropriate power source, the POWER light illuminates, indicating that the unit is energized. Vicon strongly recommends the use of line conditioners, voltage regulators, and uninterruptible power supply (UPS) systems. Pan-and-Tilt Pan is the horizontal change in camera direction, moving the field-of-view to the left or right. -
Page 16: Maintenance
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 17: Technical Information
Cable Requirements: Pan-and-Tilt: 8 conductor, unshielded. Lens: 5 conductor, shielded. Housing: 6 conductor, unshielded. Connectors: P/T output: Vicon part no. 1806-5003-07. (Mating connector supplied.) Lens output: Vicon part no. 1806-5003-05. (Mating connector supplied.) Housing output: Vicon part no. 1806-5003-06. (Mating connector supplied.) Operating Distances: The maximum operating distance is determined by the particular pan-and-tilt drive used. - Page 18 Dimensions (max): Height: 3.13 in. (79.5 mm). Width: 10.0 in. (254 mm). Depth: 8 in. (203 mm). Weight: 4.5 lb (2.0 kg). Construction: Cast iron gray plastic housing; black plastic bezel. 10 • • Technical Information X458 Rev 700 V1101C...
Need help?
Do you have a question about the V1101C and is the answer not in the manual?
Questions and answers