Table of Contents
Advertisement
Preparation for upgrade
Instructions for
upgrading
Getting the password for
This section describes the upgrade proce-
dures for your navigation system.
authentication
The update has two phases.
For upgrade, an unique password issued on-
line is necessary. Access the website with your
PC and get your password.
The following information is required.
Phase 1: Update the database
! Media Number (MEDIA NUMBER) printed
on supplied Media Number Card
(MEDIA NUMBER CARD)
! Device Number (DEVICE NUMBER) of your
navigation system
p If you don't have the web-connected com-
puter for the online issuance of password,
please contact your Authorized Pioneer
In this phase, take notice of the following:
Electronics retailer or call the companies
listed at "After-sales service for Pioneer pro-
! All functions other than the radio are dis-
abled during update. You can perform sim-
ducts".
plified operations by using the TRK (c/d)
button and VOL (b/a) button. (We recom-
1
Access on the following website to
mend changing the AV source to "AM" or
issue your password.
"FM" before you start the update.)
http://www.pioneernavigationupdate.com
! The update takes approximately 3 hours in
In Canada:
total.
http://www.pioneernavigationupdate.ca
! If you turn the ignition switch off (the navi-
For issuing the password, follow the instruc-
gation system turns off) or eject the up-
tion on the website.
grade disc, the update resumes when the
2
Record the password that you received.
navigation system turns on or the disc is re-
inserted.
You need to input this password accurately.
Write down your password to avoid mis-
takes.
Phase 2: Update the system
program
In this phase, take notice of the following:
! No functions are available.
! The update takes approximately 10 min-
utes.
! NEVER stop the engine of your vehicle nor
3
Press the OPEN CLOSE button and in-
turn off the power supply to the navigation
sert the upgrade disc into the disc loading
system until the installation is completed.
slot.
Turning the power off in this phase causes
a malfunction or failure of the navigation
system.
CAUTION
For users who use AVIC-Z3 or use the hardware up-
graded by CNDV-800HD, updating another software
program will begin first.
While this screen is visible, NEVER switch the
Upgrade procedures
ignition key position or turn off the power of na-
vigation system.
1
Park your vehicle in a safe place.
Leave the engine on, and make sure that the
parking brake is applied.
2
Press the MAP button to display the
current location.
After the installation is complete, the navigation sys-
tem restarts.
Check the details of the caution message and touch
[OK].
p The users who use other models can skip this
caution and proceed to the next step.
The message confirming whether or not to
start the update will appear.
p If the message doesn't appear, eject the
disc and display the map of your current po-
sition and then reinsert the disc.
4
Touch [Yes].
Be sure to display the map of your current po-
sition. Updating cannot start if others screens,
such as scroll mode, navigation menu or AV
screens are displayed.
p To cancel the update, touch [No].
5
Touch [Yes].
After you touch [Yes] in this screen, you can-
not abort the update until the installation of
the system program finishes.
The update takes approximately 3 hours in
total.
The message "Password obtained from
Pioneer should be entered to update. Have
you obtained the password? Please press
"Cancel" to stop update." appears.
To start the update, touch [Yes].
Alternative options:
No:
When the update of map database is com-
Shows the device number (Device#) of your
pleted, the finished message appears.
navigation system.
Cancel:
8
Touch [OK] to restart the system.
Cancels the update.
6
Enter the password for authentication
that you obtained, then touch [OK].
p After touching [OK], the installation of sys-
tem program begins.
After you touch [OK], the system starts the
CAUTION
While this screen is visible, NEVER switch
authentication. When the authentication is fin-
the ignition key position or turn off the
ished properly, a message for confirmation
power of navigation system.
will appear.
7
Touch [Yes] to start the update.
After the installation is complete, the naviga-
tion system restarts.
The navigation system restarts and then the in-
stallation begins.
Renewed points through
this upgrade
9
Check the details of the caution mes-
If you upgrade your navigation system by this
sage and touch [OK].
disc, the system will have the following
changes.
10 Touch [OK].
The map of your surroundings is displayed.
You can operate the navigation system by
touching keys displayed on the screen as
Renewal data
usual.
The following data are updated:
! Map database
11 Press the OPEN CLOSE button and press
®
! Gracenote
Database
the EJECT button to eject the upgrade disc.
! XM Satellite Radio in the lineup and icon of
the broadcast station
Checking whether the upgrade
was done properly
POI data coverage
Display "Service Information" screen to com-
Approximately 11 million POIs are included in
pare the current version number with the pre-
the database.
vious one.
p For the modified categories that can be
= For details of the operation, refer to Check-
used on "Overlay POI", "Vicinity Search"
ing the current version.
and used on the voice recognition, refer to
Category list for vicinity search (Renewal).
p Some POI information may not be accurate
or may become inaccurate through the
passage of time. Please directly contact the
POI to verify the accuracy of the informa-
tion about the POI which appears in this
database. POI information is subject to
change without notice.
Keyboard operation
Input screen of "Address Search" and
"POI Search"
Sym., 0-9:
Touch to toggle the selection.
Advertisement
Table of Contents
