Table of Contents
Advertisement
Quick Links
Contact Toaster
Owner's Manual
Models
SCT4000, SCT4000E
This manual includes material related to installation,
use , cleaning, and care. Exploded view[s], as well
as any available parts list[s] pertaining to the unit
covered by this manual are also included.
This manual must be read and understood by all
persons using or installing this appliance. Contact
your Star dealer if you have any questions concerning
installation, use, or maintenance of this equipment.
DO NOT DISCARD THIS MANUAL.
SCT4000E
2M-Z21667
Rev. C
03.2017
•
•
Advertisement
Table of Contents
Related Manuals for Star SCT4000
Summary of Contents for Star SCT4000
- Page 1 This manual must be read and understood by all persons using or installing this appliance. Contact your Star dealer if you have any questions concerning installation, use, or maintenance of this equipment. DO NOT DISCARD THIS MANUAL.
- Page 2 Defects that occur as a result of normal use, within the time installation sheet and/or owner’s manual, including incorrect period and limitations defi ned in this warranty, will at Star’s discretion gas or electrical connection. Star is not liable for any unit which...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Warranty General Information and Installation 1–2 Folding Conveyors Out Bun Height Adjustment PTFE Sheet Replacement Daily Operation Cleaning Additional Electronic Settings 6–7 Control Label Replacement Exploded Views 8–9 Parts List 10–11 Wiring Diagrams 12-13 Specifications... - Page 4 NOTES...
- Page 5 fi elds ready when you call to ensure a faster service. Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability. Due to periodic changes in designs, methods, procedures, policies, and regulations, the specifi cations contained in this document are subject to change without notice.
-
Page 6: General Information And Installation
GENERAL SAFETY INFORMATION This equipment is designed and sold for commercial use only, and is intended for use by personnel trained and experienced in its operation. This is not sold for consumer use in and around the home nor for use directly by the general public in food service locations. Before using your new equipment, read and understand all the instructions and labels associated with the unit prior to putting it into operation. -
Page 7: Folding Conveyors Out
FOLDING OUT CONVEYORS THESE PARTS GET VERY HOT WHILE IN USE, SO PLEASE MAKE CERTAIN THAT THE UNIT HAS COOLED BEFORE ATTEMPTING THE BELOW PROCEDURES. IF THERE IS AN IMMEDIATE NEED TO PERFORM THIS PROCEDURE WHILE THE UNIT IS STILL HOT, MAKE CERTAIN TO WEAR APPROPRIATE THERMAL PROTECTION. -
Page 8: Daily Operation
Adjustments made here will reset to the original time after the cycle time has finished. lower ▼ button [LIGHTER] ANALOG VERSION [SCT4000] START UP / PREHEAT [PROGRAM] button i. When the toaster has been plugged into a suitable outlet and power supply, the power switch can be flipped to turn the unit on. -
Page 9: Cleaning
OTHER TOASTER FUNCTIONS [SCT4000E ONLY] COOLDOWN MODE COOLDOWN mode can be activated by holding the COOLDOWN button and the both upper ▼ buttons for a few seconds. COOLDOWN mode causes the heaters to be turned off, 14 : 55 but the conveyors, display, and fan to continue functioning. This mode can be used for cleaning or simply cooling off the unit. -
Page 10: Additional Electronic Settings
PRODUCT SETTINGS AND ADJUSTMENTS [SCT4000E ONLY] The Star contact toaster comes with pre-programmed factory default settings for toasting some products, although the settings will need to be adjusted to accurately toast your specific buns. User defined settings can be saved with no set limit to the variations that can be used. - Page 11 ADVANCED PROGRAMMING [SCT4000E ONLY] CREATING A NEW UPDATE FILE i. If a .csv file with the correct format for uploading new preset names and settings into the toaster has not already been loaded onto a USB flash drive, a file with the correct format can be generated by plugging a USB flash drive into the toaster while it is on.
-
Page 12: Control Label Replacement
ELECTRONIC AND COMMON COMPONENTS CONTROL LABEL REPLACEMENT i. Remove the two [2] screws holding the bezel on. ii. Lift off the bezel, gasket, and label. iii. Place new label, bezel, and gasket in place in the order displayed on the right. iv. - Page 13 ANALOG COMPONENTS...
-
Page 14: Parts List
2M-Z22076 bun thickness label 2A-Z12583 0.375-inch e-clip 2R-Z21448 linkage handle 2A-Z11501 foot HC-Z21510 discharge tray HC-Z21511 crossbar 2P-Z8779 SCT4000 sprocket [25p-11t] 2P-200645 SCT4000 sprocket [25B17] HC-Z21531 SCT4000 sprocket mount bracket 2P-200650 SCT4000 sprocket [25B24] HC-Z21513 SCT4000E guard... - Page 15 2K-Y6764 strain relief bushing 8, 9 HC-Z21524 SCT4000E motor mount 2E-Z21509 SCT4000E fan guard 2C-Z5883 SCT4000E 10-24 self-tapping screw 2R-Z22044 SCT4000 control knob 2T-Z21434 SCT4000 thermostat HC-Z21532 SCT4000 motor mount bracket 2C-Z7165 8-32 keps nut 2H-Z21527 PTFE platen insulation 2I-Z21439...
-
Page 16: Wiring Diagrams
WIRING DIAGRAM SCT4000E USB CONNECTOR CAT 5E CABLE HEATER PLATEN DISPLAY BOARD STEPPER MOTOR REAR STEPPER MOTOR FRONT MOTOR WIRES POWER CHORD POWER SWITCH HIGH LIMIT THERMOSTAT GROUND TO CHASSIS CPU BOARD MOTOR BOARD WAGO CONNECTOR 9 10 CAT 5E CABLE POWER SUPPLY COOLING FAN... -
Page 17: Wiring Diagrams
WIRING DIAGRAM SCT4000 ADJUSTABLE THERMOSTAT HEATER PLATEN POWER CHORD HIGH LIMIT THERMOSTAT POWER SWITCH GROUND TO CHASSIS WAGO CONNECTOR WAGO CONNECTOR AC MOTOR SHEET 1 OF 1... -
Page 18: Specifications
(34 kg) 11.1 2,663 6-15P 2,065 6-15P 25.7 in. 21.7 in. 9.5 in. 100 lb. 75 lb. SCT4000 2.525 CEE7-7 (653 mm) (551 mm) (241 mm) (45.4 kg) (34 kg) 11.5 2,750 6-15P 1without butter wheel [butter wheel extends out and adds 4.2 in. (107 mm) to unit depth]. - Page 19 NOTES...
- Page 20 STAR MANUFACTURING INTERNATIONAL INC. Printed in the U.S.A. • 2M-Z21667• Rev C • 03.2017 Specifications are subject to change without notice. 10 Sunnen Drive Saint Louis, Missouri 63143 • Telephone 800 264 7827 Fax 314 781 5445 • www.star-mfg.com...
Need help?
Do you have a question about the SCT4000 and is the answer not in the manual?
Questions and answers