BIRO AFMG-24 Operating And Service Manual
Mini automatic mixer grinder/chopper
Hide thumbs
Also See for AFMG-24:
- Operating and service manual (27 pages) ,
- Operating and service manual (32 pages)
Related Manuals for BIRO AFMG-24
Summary of Contents for BIRO AFMG-24
- Page 1 � � IMPORTANT NOTICE This Manual contains important safety instructions which must be strictly followed when using PTCT this equipment. AFMG-24 220-10-08-13 220-9-05-11...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page NOTICE TO OWNERS AND OPERATORS ..........1 SAFETY TIPS. -
Page 3: Notice To Owners And Operators
Warnings related to possible damage to the equipment are indicated by: BIRO also has provided warning labels on the equipment. If any warning label or Manual be- comes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement. -
Page 4: Safety Tips
� NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate Machine With Missing Parts. � PROMPTLY REPLACE Any Worn or Illegible Warning Labels. � ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning, or Servicing. � USE ONLY BIRO Parts and Accessories Properly Installed. -
Page 5: Installation
UNCRATING AND SET UP 1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO first. -
Page 6: Motor Wiring And Electrical Requirements
8. The size of the electrical wiring required from the power source to the mixer grinder is a MINIMUM OF No. 10 WIRE. 9. The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD... - Page 7 16. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product. 17. Use meat deflector attached to grinding bowl to eliminate meat splatter. 18. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.
-
Page 8: Operation
OPERATION ROTATING GRINDING AUGER & ROTATING MIXING PADDLE TO AVOID SERIOUS PERSONAL INJURY • ONLY Properly Trained Personnel Should Use This Equipment. � ONLY Properly Trained Personnel Should Use This Equipment. • NEVER Place Hands Into Machine Input or Output Openings. •... -
Page 9: Cleaning
� NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other Electrical Components. � ALWAYS Thoroughly Clean Equipment at Least Daily. CLEANING THE BIRO MIXER GRINDER 1. Disconnect mixer grinder from power source and perform lockout/tagout procedures. 2. Remove grinding bowl end ring, breaker plate, knife and grinding auger. -
Page 10: Maintenance
� NEVER Bypass, Alter or Modify This Equipment in Any Way From Its Original Condition. � PROMPTLY REPLACE Any Worn or Illegible Warning Labels. � USE ONLY GENUINE BIRO Parts and Accessories Properly Installed. A. MIXING PADDLE INSTALLATION 1. Check that mixer paddle drive pin (Item No. 53516) in the mixer paddle drive shaft (Item No. 53955) is positioned vertically. -
Page 12: Parts Diagrams
FASTENERS FRAME & CASE ADJUSTABLE LEGS TO FRAME Item # HHS067S Hex head screw -16 � , SS, (8 ea.) HN35S Hex nut, -16, SS, (8 ea.) LW25S Lock washer, , SS, (8 ea.) TRANSMISSION MOUNTING PLATE SUPPORTS TO FRAME Item # HHS075S Hex head screw... -
Page 13: Mixer
MIXER MIXER MIXER Fig. Item No. Description Fig. Item No. Description Fig. Item No. Description MIXER 53568 Mixer paddle lock set screw 53568 Mixer paddle lock set screw 53568 Mixer paddle lock set screw 53594 Lock arm radial bearing 53594 Lock arm radial bearing 53594 Lock arm radial bearing... -
Page 14: Power Transmissions
FASTENERS POWER TRANSMISSION MIXER TRANSMISSION TO MOUNTING PLATE JOURNAL BOX TO MOUNTING PLATE Item # Item # HHS126-GR5 Hex head screw -13 � 1 , SS, (4 ea.) HHS070S Hex head screw -16 � 1, SS, (4 ea.) LW30S Lock washer, , SS, (4 ea.) LW25S Lock washer,... - Page 15 Fig. Item No. Description 56211-1 Driven clutch engagement lever bushing SSB50PS SSB50P Shoulder bolt, dia. � lg. S/N 20405 on H310A Bearing assembly (journal box front) 53785 Seal, journal box (front, auger drive) 56036 Driven clutch engagement shaft 56215 Driven clutch engagement lever, RH 56047 Mounting plate for transmission 56063...
-
Page 18: Power Controls (Electrical)
POWER CONTROLS Fig. Item # Description Fig. Item * Description 50768 Switch, start, pushbutton (order H482-1) H481AE-52 Overload; AEG-B27T-L; 5HP; 460-575V, 60Hz, 50769 Switch, stop, pushbutton (order H482-2) 3Ph; range 5.6-8 amps 51991 Fuseholder H481AE-53 Overload; AEG-B27T-M; 7 HP; 575V, 60Hz, 56301G Watertight 90°... -
Page 19: Retrofit Aeg Contactors In Control Box
RETOFIT FOR AEG CONTACTORS RETROFIT FOR AEG CONTACTORS IN AFMG-24 CONTROL BOX SERIAL NO. 20001 ON IN AFMG-24 CONTROL BOX The magnetic contactors and overloads in the AFMG-24 have been changed to AEG electrical com- ponents starting with Serial No. 20260 (5HP) and Serial No. -
Page 20: (114Mm Unger & Enterprise)
OPTIONAL STAINLESS STEEL BOWLS, AUGERS & PINS 114mm UNGER SYSTEM ENTERPRISE SYSTEM Item No. Description HR42/48S End ring, SS 54278-CTNS Auger assembly, SS HHS012S Hex head screw, 10-32 � , SS 56049S Bowl w/plate pins, SS HK114 Knife drive pin, 114mm Unger HR42/48S-114 End ring, SS, 114mm Unger 54278C Auger shear pin... -
Page 21: Items Required For Tandem Operation
ITEMS REQUIRED FOR TANDEM OPERATION... -
Page 24: Optional Equipment Illustrated
OPTIONAL... -
Page 25: Warning Label Locations On Machine
SAFETY LABEL LOCATIONS... -
Page 26: Tandem Operation Illustration For 90º Inlet
TANDEM OPERATION ILLUSTRATION FOR 90º INLET... -
Page 27: Tandem Connection Illustrations
TANDEM OPERATIONS BIRO AFMG-24 into BIRO AFMG-24 BIRO Heavy Horsepower Grinder into BIRO AFMG-24 Remove Side Entrance Seal, Item No. 56167; Outer Disc, Item No. 54303 and Lock Knobs, Item No. 14688 from the inlet tube of the Second Grind Machine. -
Page 28: Operator's Signature Page
OPERATOR'S SIGNATURE PAGE MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN CAUSE SE- RIOUS INJURY TO MYSELF AND OTHERS. SUPERVISOR’S NAME (PRINT) SIGNATURE DATE INITIALS... -
Page 29: Operator's Notes
— NOTES —... -
Page 30: Limited Warranty
BIRO will replace defective parts, which are covered by this limited warranty, provided that the de- fective parts are authorized for return, shipping charges prepaid, to a designated factory for in- spection and/or testing.
Need help?
Do you have a question about the AFMG-24 and is the answer not in the manual?
Questions and answers