Table of Contents
Advertisement
S
etting
U
p
S
U
Setting the Video Channel
This VCR is designed to send picture and sound
signal on UHF channel E36 to the TV, through the
RF coaxial cable.
If you want to change this video channel (E36) to
another channel (between E28 to E60), follow the
procedure below before turning on the VCR for the
first time.
1 Make sure the VCR is turned off and no
cassette is inserted.
2 Turn on the TV, and tune it to any channel (UHF
28 to 60) you want to use as the video channel
on the TV.
• Select a channel not used in your area.
3 Press STOP/EJECT
more than 5 seconds.
The following indication appears on the display.
TV system number starts flashing.
5
∞
4 Press CH
/
on the front panel to select an
appropriate TV system number for your area.
1: For B/G. (For West Europe, ASEAN coun
tries, New Zealand)
2: For D/K. (For China, Russia, East Europe)
3: For I. (For Hong Kong, South Africa, United
Kingdom)
5 Press OK/STATUS.
The channel number starts flashing on the
display.
Channel number starts flashing.
5
∞
6 Press CH
/
on the front panel to select the
channel you have tuned on the TV as the video
channel in step 2.
Test signal
(two vertical white bars)
7 Press OK/STATUS to finish the video channel
setting.
To watch a picture from this VCR on the TV,
select the same channel you have selected as the
video channel (in step 2 above) on the TV.
If you use only external video input (AV) mode to
watch the picture from this VCR:
You can turn off the video channel output. To turn off
the video output channel, press CH
appears on the channel number position.
7
0
/
on the front panel for
∞
until "– –"
Menu Operations
Before operating the VCR, be familiar with the
menu operations first because most of the features
built into the VCR can be available only on the
menus.
1 Press VCR on the remote control.
• When using the buttons on front panel, skip this step.
2 Press MENU to display the main menu screen.
5
3 Press PLAY
or STOP
feature on the menu, then press OK/STATUS.
4 When you select a feature, go to the section in
this manual and follow the instructions described
there.
To go back to the previous menu screen, press
2
REW
.
To change the setting of a menu item, press FF
Press MENU to exit.
Initial Set Up
For the first time you turn on this VCR, some basic
settings must be done first before going on to further
operations.
1
Select the Language
1 Press POWER.
The language selection screen
appears.
5
2 Press PLAY
or STOP
to select either "ENGLISH",
or "
" (Chinese).
3 Press OK/STATUS.
2
Setting the Clock/Date
5
1 Press PLAY
or STOP
set the time. Each time you
press the button, the set time
changes by one-minute inter-
vals.
Press and hold the button to change time by 30-
minute intervals.
When the time is correct, press OK/STATUS.
5
2 Press PLAY
or STOP
time you press the button, the date changes in
one-day increments. Press and hold the button to
change dates in 15-day increments. When the date
is correct, press OK/STATUS.
5
3 Press PLAY
or STOP
time you press the button, the year changes by
one-year intervals. Press and hold the button to
change years rapidly. When the year is correct,
press OK/STATUS.
5
∞
to select a desired
3
ENGLISH
∞
SELECT:
CONFIRM: OK
END: MENU
∞
to
TIME - - : - -
DATE 01/01/01
SET:
NEXT: OK
END: MENU
∞
to set the date. Each
∞
to set the year. Each
.
Advertisement
Table of Contents
