Download Print this page

Advertisement

Quick Links

BABY WOLF LOOM
A
ssembly
BEFORE YOU BEGIN
■ Please read through the directions before beginning to
assemble your loom.
■ Unpack the loom parts carefully. Do not throw away
the carton or any of the packing material until you have
checked to see that all of the parts and hardware have been
received
■ All hardware is sized in inches. Illustrations of the vari-
ous hardware and an inch scale are provided to aid you in
determining the correct piece of hardware to use.
■ Before starting the assembly, read the instructions com-
pletely and familiarize yourself with the drawings and parts.
■ Follow the exact order of assembly. Take care and work
slowly. If you have someone to help you, the assembly will
be easier.
TOOLS
#2 Phillips screwdriver
5/16" or adjustable wrench
Flat screwdriver
HARDWARE LIST
Note: Parts pictures are not to scale. Listed part quantities
are what is needed for assembly. There may be extras of
some parts. Parts may not be pictured in every listed size.
HARDWARE BAG A – STEPS 1-3
4 – Fold bars
4 – 3/16" x 1-1/4" carriage bolts
4 – 3/16" lock nuts
8 – 3/16" washers
2 – 1/4" washers
2 – 5/16" lock nuts
2 – Black knobs w/ 1" threaded shaft
2 – Plastic bearings
HARDWARE BAG B – STEPS 4-8
6 – 1/4" x 2" machine screws
6 – 1/4" barrel nuts
1 – Ratchet advance lever
2 – 3/8" USS washers
4– #8 x 1-1/2" screws
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273
© 2017 Schacht Spindle Company, Inc.
I
nstructIons
K
for
nocKed
■ The wood parts have a removable label on them to iden-
tify each part. We recommend that you leave the labels in
place until the loom is fully assembled.
■ When you finish assembling the Wolf loom, go back over
all of the screws and make sure they are tight. It is a good
idea to re-tighten the screws every few months. Remember
not to tighten those screws and bolts which are supposed
to allow their parts to pivot.
■ All wooden parts of the loom have been finely sanded
and finished with hand-rubbed Danish oil. From time to
time you may wish to apply more finish to the loom. Use a
Danish oil (tung oil and polyurethane mixture) and hand
rub the wood with a soft, lint-free cloth. Be sure to follow all
the manufacturer's instructions.
1-1/4" carriage bolt
1-1/2" machine screw
2" machine screw
2-1/2" carriage bolt
1-1/2" screw
Ratchet advance lever assembly
Fold bar
- 1 -
-d
l
own
ooms
Plastic bearing
Knob w/ 1" shaft
Wing nut
Lock nut from top
Slim lock nut
Lock nut
Barrel nut
04.17

Advertisement

loading
Need help?

Need help?

Do you have a question about the BABY WOLF LOOM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Schacht BABY WOLF LOOM

  • Page 1 2 – 3/8" USS washers 4– #8 x 1-1/2" screws Ratchet advance lever assembly Fold bar Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 04.17 © 2017 Schacht Spindle Company, Inc. - 1 -...
  • Page 2 HARDWARE BAG C - STEPS 9-10 ⅛ 2 – 1/4" x 2" machine screws Jack pivot rod ¼ ⅜ 4 – 1/4" barrel nuts ½ 2 – #8 x 1-1/2" screws 2 – 1/4" x 2-1/2" carriage bolts ¾ Hex nut O-ring 4 –...
  • Page 3 HARDWARE BAG H - STEP 24-25 2 – 1/4" barrel nuts 2 – Fender washers 2 – Black knobs with 2-1/4" threaded shaft Beater pin holder 1 – Beater pin and chain 1 – Beater pin holder 1 – #6 x 5/8" screw Beater pin and chain HARDWARE BAG I - STEP 26-27...
  • Page 4 ASSEMBLY INSTRUCTIONS fold bars Attach the fold bars to the legs. Parts: two pairs of legs, 4 – fold bars, 4 – 3/16" x 1-1/4" 3/16" lock nut carriage bolts, 8 – 3/16" washers, 8 – 3/16" lock nuts. 3/16" washer 1-1/4"...
  • Page 5 Attach the fold bars to the castle. top of right castle side Parts: 2 – plastic bearings, 2 – black knobs with 1" thread- front of loom ed shaft. Flip the legs/castle side assemblies so they are lying with right castle side the slot in the castle side facing up.
  • Page 6 Install the cloth beam and ratchet advance lever. Parts: cloth beam, ratchet advance lever, 2 – 3/8" USS cloth beam washers. Place the ratchet advance lever on the axle of the cloth cloth beam support beam, next to the ratchet gear. Place a washer on each end cloth beam support of the cloth beam.
  • Page 7 Assemble the beater. Parts: Beater sides, beater top, beater race, 2 – 1/4" x 2" machine screws, 4 – 1/4" barrel nuts, 2 – #8 x 1-1/2" 1/4" x 2-1/2" carriage bolt machine screws, 2 – 1/4 x 2-1/2" carriage bolts, 2 – 1/4" washers, 2 –...
  • Page 8 Install the jacks and lamms. two washers on each rod Parts: 2 – jack pivot rods. jack pivot rods For 4-shaft looms: 14 – 3/8" SAE washers, 2 – #1 jack as- semblies, 2 – #3 jack assemblies. back side of front For 8-shaft looms: 22 –...
  • Page 9 Repeat for the other shafts. Note: This process is covered in the video Assembling the Baby Wolf Loom. You can find the video at youtube.com/ Figure 14 D - HeDDLeS iNSTALLeD ON SHAFT user/schachtspindle.
  • Page 10 Note: This process is covered in the video Assembling the Figure 15 - SeCure THe JACK PiNS Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. upper rear castle cross brace 1-1/2"...
  • Page 11 Install the brake barrel nut. Parts: 1 – 1/4" x 1" machine screw, 1 – long brake barrel nut. From the outside of the inside right leg, push the screw through the leg, and tighten into the brake barrel nut. inside right leg inside right leg 1"...
  • Page 12 Install the warp beam crank handle. Parts: 1 – warp beam crank handle, 1 – 3/8" washer, 1 – 3/8" cap nut. Place the 3/8" washer and then the metal crank handle 3/8" washer cap nut on the threaded shaft extending through the leg from the brake end of the warp beam.
  • Page 13 (rear) Note: This process is covered in the video Assembling the button Baby Wolf Loom. You can find the video at youtube.com/ user/schachtspindle. Figure 26 - iNSTALL THe Tie-uPS ON THe LAMMS Install the apron bars.