Cleco 8 Series Service Manual
  1. Manuals
  2. Brands
  3. Cleco Manuals
  4. Power Screwdriver
  5. 8 Series
  6. Service manual

Cleco 8 Series Service Manual

Rolling impulse clutch, positive clutch and stall screwdrivers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Parts Manual
823126
04/07/2011
8 Series
Rolling Impulse Clutch, Positive Clutch and Stall Screwdrivers
For additional product information visit our website at http://www.apextoolgroup.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cleco 8 Series

Summary of Contents for Cleco 8 Series

  • Page 1 Parts Manual 823126 04/07/2011 8 Series Rolling Impulse Clutch, Positive Clutch and Stall Screwdrivers For additional product information visit our website at http://www.apextoolgroup.com...

  • Page 2: Safety Recommendations

    Cleco screwdrivers are designed to operate on 90 psig arms. Vibration may contribute to a condition called (6.2 bar) maximum air pressure. If the tool is properly Raynaud's Syndrome.
  • Page 3 Safety Recommendations Any tool operator should be aware of the following warning Work gloves with vibration reducing liners and wrist sup- signs and symptoms so that a problem can be addressed ports are available from some manufacturers of industrial before it becomes a debilitating injury. Any user suffering work gloves.
  • Page 4 OPERATING INSTRUCTIONS READ SAFETY RECOMMENDATIONS ON PAGES 2 AND 3 BEFORE CONNECTING TOOL. ROLLING IMPULSE CLUTCH AIR SUPPLY Torque control in this clutch does not depend on air pres- The tool is designed to operate at 90 psig air pressure. The sure, but is achieved by presetting the clutch to the desired air pressure should be checked at the tool's air inlet while torque.
  • Page 5 SERVICE INSTRUCTIONS If replacement of the idler gear pins is necessary, they DISASSEMBLY — GENERAL should be pressed out the rear of the spider See Fig. 1 for (ALL MODELS) replacement pin height. Clamp the backhead in a soft-jawed vise and unscrew (left hand threads) the clutch housing and remove the clutch assembly.

  • Page 6: Clutch Reassembly

    SERVICE INSTRUCTIONS BACKHEAD DISASSEMBLY REASSEMBLY - GENERAL Lever Reassembly of all of the various sub-assemblies is in the For inspecion or replaement of the throttle valve seal, No. reverse order of disassembly; however, the following para- 847426, unscrew and remove the throttle valve cap, No. graphs list some of the more important reassembly proce- 832207.

  • Page 7: Safety Check

    SERVICE INSTRUCTIONS SAFETY CHECK After repair or replacement of parts, tools equipped with an automatic shut-off device should be tested at low torque .0015" (.038mm) and 90 p.s.i.g. to verify that the device is functioning Clearance properly. PISTOL GRIP AND OFFSET HANDLE When installing the throttle link pin, No.
  • Page 8 FINDER ROLLING IMPULSE CLUTCH QUICK-CHANGE ROLLING IMPULSE CLUTCH 869952 202839 202819 841284 202839 619524 202833 833688 202842 FINDER SPRING 412055 863455 863455 PART NO. FORCE WIRE DIA. 864249 867876 865728 LIGHT .020" 867938 847104 844000 MEDIUM .033" 867875 202820 863455 863455 867876 867938...
  • Page 9 - 7, & - 10 GEAR TRAINS -7 867922 -7 869258 -10 884125 -10 867903 867902 847147 -10 ONLY 203062 832128 -7 867921 867904 -10 867925 869584 844364 867906 867907 -7 869259 -10 867905 -7 & -10 GEAR TRAINS PARTS LIST — - 7, & - 10 GEAR TRAINS PART NO.

  • Page 10: Parts List

    QUICK-CHANGE CHUCK STALL TYPE SCREWDRIVER GEAR TRAINS 869258 867903 867922 884125 832128 867904 867907 869584 202031 202833 202827 -7, -10 202312 (-10 Only) 864249 833688 833688 844265 619524 202032 202842 864249 867902 869259 843635 867905 (-10 Only) 867921 867921 867925 867922 867921 867922...
  • Page 11 FRONT BEARING MOTORS Model Part No. 847095 REAR CYLINDER PIN 847609 Non-Rev. Lever 833718 Rev. Lever 812167 Rev. Offset 812167 Rev. Pistol 844234 SPACER Model Part No. REAR BEARING PLATE 869180 Non-Rev. 867854 Rev. 867937 847603 867873 Pistol Models 863738 Only 867873 847609...
  • Page 12 ROLLING IMPULSE AND STALL LEVER HANDLE FOR RSCL AND SCL Reversible Tools Only 869253 Locking (Opt.) 202674 Non-locking (Std.) 867878 865770 832207 412603 844060 847426 869036 832636 867874 865728 869510 867882 833300 867877 863454 202410 867857 Non-Rev. Tools Only Non-Rev. 869044 Rev.
  • Page 13 REVERSIBLE OFFSET HANDLE FOR RNO, RSO AND RSCO 202020 202339 869253 Locking 865770 867878 202674 Non-locking 867915 844787 867911 201905 412775 867916 869200 869350 847411 833303 847033 847767 847272 Part No. Name of Part Qty. Part No. Name of Part Qty.
  • Page 14 PISTOL HANDLE WITH TRIGGER FOR RSCP, RSP AND RNP 613749 869852 202773 867898 847272 617290 867926 202760 843572 844787 867939 201905 412775 867929 867933 202828 847411 833303 847033 202782 202951 847272 PARTS LIST — PISTOL HANDLE WITH TRIGGER PART NO. NAME OF PART QTY.
  • Page 15 NOTES...

  • Page 16: Sales & Service Centers

    Sales & Service Centers Note: All locations may not service all products. Please contact the nearest Sales & Service Center for the appropriate facility to handle your service requirements. Dallas, TX Detroit, MI Houston, TX Lexington, SC Apex Tool Group Apex Tool Group Apex Tool Group Apex Tool Group...

Table of Contents