jobmate 054-7102-8 Owner's Manual

jobmate 054-7102-8 Owner's Manual

1/4 sheet pad sander

Advertisement

Owner's Manual
1/4 Sheet Pad Sander
054-7102-8
CAUTION:
Before using this pad
sander or any of its
accessories, read this
manual and follow all
Safety Rules and
Operating Instructions.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Rev 1.7
31/10/2009
General Safety Rules
Specific Safety Rules
and Symbols
Functional Description
Assembly
Operation
Maintenance
Accessories

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 054-7102-8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for jobmate 054-7102-8

  • Page 1 Owner’s Manual 1/4 Sheet Pad Sander 054-7102-8  General Safety Rules CAUTION:  Specific Safety Rules Before using this pad and Symbols sander or any of its  Functional Description accessories, read this  Assembly manual and follow all ...
  • Page 2: Table Of Contents

    This product is not guaranteed against wear or breakage due to misuse and/or abuse. This product is not guaranteed if used for industrial or commercial purposes. TOLL FREE HELPLINE: 1-866-JOBMATE SPECIFICATIONS Rating ……………………… 120 V 60 Hz AC Amperes ……………………...
  • Page 3: Power Tool Safety

    POWER TOOL SAFETY WARNING: To avoid electrical hazards, fire hazards or damage to the pad sander, use proper circuit protection. The pad sander is wired at the factory for 120 V operation. It must be connected to a 120 V, 15 A time delayed fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
  • Page 4 POWER TOOL SAFETY Don’t expose power tools to rain or wet GENERAL SAFETY RULES conditions. Water entering the power tool will increase the risk of electric shock. WARNING: Read and understand all instructions. Failure to follow all Do not abuse the cord. Never use the instructions listed below may result in cord to carry the tools or pull the plug from electric shock, fire and/or serious personal...
  • Page 5: Specific Safety Rules

    POWER TOOL SAFETY Do not overreach. Keep proper footing Check for misalignment or binding of and balance at all times. Proper footing moving parts, breakage of parts and any other condition that may affect the tool’s and balance enables better control of the operation.
  • Page 6: Extension Cord Guidelines

    SPECIFIC SAFETY RULES WARNING: An undersized cord will cause a drop in line Non-compliant voltage resulting in loss of power and eyewear can cause serious injury if overheating. The table below shows the broken during operation of a power tool. correct size to use according to cord length and nameplate ampere rating.
  • Page 7 SYMBOLS WARNING: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. three-phase alternating volts current with neutral amperes direct current hertz...
  • Page 8: Know Your Pad Sander

    KNOW YOUR PAD SANDER Palm grip ON/OFF switch Dust bag Sandpaper Cooling clamp vents Sandpaper Backing clamping lever...
  • Page 9: Accessories

    ACCESSORIES & CARTON CONTENTS AVAILABLE ACCESSORIES WARNING: Use only accessories recommended for this pad sander. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the pad sander. Do not use any accessory unless you have completely read the instructions or Owner’s Manual for that accessory.
  • Page 10: Assembly & Operation

    ASSEMBLY & OPERATION INSTALLING DUST BAG ASSEMBLY Carefully shake the dust bag with the elasticized opening pointing downward Insert dust duct bag assembly sleeve to remove the sanding dust. (1) into dust chute (2) (see Fig. 1). NOTE: It is best to perform this NOTE: Make sure the tabs (3) insert function outdoors over a trash can to into the matching slots (4) in the dust...
  • Page 11 ASSEMBLY & OPERATION INSTALLING SANDPAPER – cont’d Align the corner of the sanding pad (2) with the corner of the hole punch (3). Wrap sandpaper sheet (3) over This will ensure the holes are punched backing pad and insert it into the open in the correct location.
  • Page 12 ASSEMBLY & OPERATION In general, coarse grit will remove the most material and finer grit will produce the best WARNING finish in all sanding operations. The Have you read “POWER TOOL condition of the surface to be sanded will SAFETY”, “SPECIFIC SAFETY determine which grit will do the best job.
  • Page 13 ASSEMBLY & OPERATION SANDING – cont’d DO NOT FORCE THE SANDER. The weight of the sander usually provides Place sander on the workpiece so that the adequate pressure. Let the sander and complete sandpaper surface is in contact sandpaper do the work. Applying added with the workpiece.
  • Page 14: Maintenance

    When servicing, use fiberglass boats and sports cars, wallboard, only identical JobMate™ replacement spackling compounds or plaster. The chips parts. Use of any other part may create a and grindings from these materials are hazard or cause product damage.
  • Page 15: Parts & Service

    PARTS DIAGRAM – MODEL 054-7102-8 Pad Sander...
  • Page 16 PARTS LIST – MODEL 054-7102-8 Pad Sander When servicing, use only JobMate™ replacement parts. Use of any WARNING: other parts may create a HAZARD or cause damage to your power tool. Any attempt to repair or replace electrical parts on this power tool may create a hazard unless repair is performed by a qualified technician.

Table of Contents

Save PDF