Advertisement
PRECAUTIONS FOR SAFETY
Do not install, repair, open or remove the cover. It may
●
expose you to dangerous voltages. Ask the dealer or the
specialist to do this.
● Turning off the power supply will not prevent potential electric
shock.
● The appliance shall be installed in accordance with national
DANGER
wiring regulation.
● Means for disconnection from the supply having a contact
separation of at least 3 mm in all poles must be incorporated
in the fixed wiring.
Do not expose your body directly to cool air for a long time.
●
● Do not insert your fnger or any article into the air inlet/outlet.
● When an abnormality (burning smell, etc.) occurs, stop the
air conditioner and disconnect the power supply or turn off
the breaker.
● This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
WARNING
the appliance by a person responsible for their safety.
● Children should be supervised to ensure that they do not play
with the appliance.
● Do not use any refrigerant different from the one specifed
(R410A) for complement or replacement. Otherwise,
abnormally high pressure may be generated in the
refrigeration cycle, which may result in a failure or explosion
of the product or an injury to your body.
Do not wash the unit with water. It may cause an electric
●
shock.
● Do not use this air conditioner for other purposes such as
preserving food, breeding animal, etc.
● Do not step or put anything on the indoor/outdoor unit. It may
cause an injury or damage the unit.
● Do not touch aluminium fn because it may cause an injury.
● Before cleaning the unit, turn off the main switch or the circuit
breaker.
CAUTION
● When the unit won't be used for a long time, turn off the main
switch or the circuit breaker.
● It is recommended that maintenance be performed by a
specialist when the unit has been operated for a long time.
● The manufacturer shall not assume any liability for the
damage caused by not observing the description of this
manual.
1
INDOOR UNIT DISPLAY
j TIMER (White)
k OPERATION (White)
2
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air f lters.
2. Attach the f lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is f ashing, go to the next step 2.
2. Press
or
: adjust the time.
3. Press
: Set the time.
Remote Control Reset
Push
by tip of the pencil or
1. Remove the batteries.
.
2. Press
3. Insert the batteries.
AIRFLOW DIRECTION
3
1
Press
the desired vertical direction.
Press
2
automatically and press again to
stop.
For horizontal direction, adjust
3
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
4
REMOTE CONTROL
j Infrared signal emitter
k Start/Stop button
l Mode select button (MODE)
m Temperature button (TEMP)
n Fan speed button (FAN)
o Swing louver button (SWING)
p Set louver button (FIX)
q On timer button (ON)
r Off timer button (OFF)
s Setup button (SET)
Clear button (CLR)
11
Memory and Preset button (PRESET)
12
One-Touch button (ONE-TOUCH)
13
High power button (Hi-POWER)
14
Power selection button (POWER-SEL)
15
Quiet button (QUIET)
16
Comfort sleep button (COMFORT SLEEP)
17
Filter reset button (FILTER)
18
Set clock button (CLOCK)
19
Check button (CHECK)
20
.
Reset button (RESET)
21
Note:
• The provided Remote Controller is a wireless type, which also can be used as a
wire. Please see "How to Connect The Remote Controller for Wired Operation"
located in installation instruction, in case of wired control is required.
• In wire operation, remote controller will return to initial condition (PRESET,
TIMER and CLOCK will return to initial condition) when user shutdown power
supply of Air conditioner.
ONE-TOUCH
5
Press the "ONE-TOUCH" button for fully automated operation that is
customized to the typical consumer preferences in your region of the world.
The customized settings control temperature air f ow strength, air f ow
direction and other settings to provide you alternate contact with
"ONE-TOUCH" of the button. If you prefer other settings you can select
from the many other operating functions of your Toshiba unit.
ONE-TOUCH
Press
6
AUTOMATIC OPERATION
To automatically select cooling or fan only operation
MODE
1. Press
2. Press
3. Press
FAN
or HIGH
COOLING / FAN ONLY OPERATION
7
MODE
1. Press
2. Press
Cooling: Min. 17°C, Fan Only: No temperature indication
FAN
3. Press
or HIGH
1
: Move the louver in
: Swing the air
12
k
l
p
13
15
q
17
20
19
: Start the operation.
: Select A.
: Set the desired temperature.
: Select AUTO, LOW , LOW+
.
: Select Cool
or Fan only
.
: Set the desired temperature.
: Select AUTO, LOW , LOW+
.
j
m
o
n
SWING
FAN
ONE-TOUCH
FIX
QUIET
14
16
POWER-SEL
Hi POWER
11
COMFORT
r
SLEEP
s
21
18
, MED
, MED+
,
, MED
, MED+
,
Advertisement
