Related Manuals for Vutec Lectric 4
Summary of Contents for Vutec Lectric 4
- Page 1 Installation Instructions Lectric 2 & 4 FLUSH CEILING MOUNT SCREEN FULL TRAP DOOR CLOSURE VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 – 06/10 Rev. D 2-INSTL_D EMAIL: info@vutec.com...
-
Page 2: Important Safety Instructions
DISCLAIMER Vutec Corporation intends to make this manual accurate and complete. However, Vutec makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation for use of this product. The information contained in this document is subject to change without notice. -
Page 3: Screen Type
SELF-SUPPORTED (shown) and TAB-TENSIONED screens Figure 1 SCREEN TYPE LENGTH DIM. A SELF-SUPPORTED VIEWING WIDTH + 15 1/2 7 3/4 TAB-TENSIONED VIEWING WIDTH + 22 1/2 11 1/4 VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 – 06/10 Rev. D 2-INSTL_D EMAIL: info@vutec.com... -
Page 4: Option 1 - Suspended Mounting
HOUSING INSTALLATION Lectric 2 (Self-supporting fabric) and Lectric 4 (Tab-tensioned fabric) are designed for flush ceiling mount. These units are suitable for use in environmental air space in accordance with Section 300-22 (C) of the National Electric Code, ANSI/NFPA 70, and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electric Code, Part 1, CSAC22.1. - Page 5 INSTALLERS HEX NUT BY INSTALLER HELICAL LOCK WASHER BY INSTALLER Figure 2c Option 1 - Suspended Mounting Figure 3 Option 2 – Blind Pocket Mounting VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 – 06/10 Rev. D 2-INSTL_D EMAIL: info@vutec.com...
-
Page 6: Electrical Connections
Push the wire nuts back up in the electrical compartment and reinstall the electrical cover. Slightly tighten the screw to keep the cover in place. Close the service door and reinstall the screw at each end. VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 –... -
Page 7: First Operation
WIRING DIAGRAM - 220VAC The screen may also be operated by optional IR/RF remote control, optional 12VDC trigger relay, optional Low Voltage control or optional Home Automation control by AMX, Crestron, etc. Consult Vutec for further details. FIRST OPERATION CAUTION: THE FIRST CYCLE DOWN AND UP OF THE SCREEN MUST BE PERFORMED UNDER CONTROL OF AN ATTENDANT. THE MOTOR ... - Page 8 ⇒ Button pushed in - motor limit switch disengaged, free running, screen must be stopped by control switch. ⇒ Button pushed out - motor limit switch is engaged to stop the screen at the point at which the screen was stopped and the limit switch pushed out. VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 –...
- Page 9 When the screen stops above the desired lower limit; proceed to part to lower the screen MORE SCREEN DROP to the desired lower limit. VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 – 06/10 Rev. D 2-INSTL_D EMAIL: info@vutec.com...
- Page 10 (Figure 9). Lower the screen roller assembly out of the housing. Reinstalling the screen roller assembly with the motor included is the reverse of the removal. Be sure the limit switches facing down as shown in Figure 2a. Re-wire following Fig 4.. CAUTION: REINSTALL OF THE SCREEN ROLLER ASSEMBLY MAY REQUIRE LOWER LIMIT ADJUSTMENTS. VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 –...
-
Page 11: Weight Data
Housing components removed to illustrate details WEIGHT DATA Some standard viewing sizes are shown. Extrapolate the information for size not showing as necessary or contact Vutec for details. Divide lbs by 2.2 to obtain kgs. Viewing size (4:3) (HxW) Weight (lbs) -
Page 12: Troubleshooting
ACCESSORIES INCLUDED SPDT DECORA SWITCH SWITCH COVER PLATE MOUNTING BRACKET 1/4-20 X 1” LONG HEX HEAD BOLT HELICAL LOCK WASHER FOR 1/4 BOLT 1/4-20 HEX NUT VUTEC CORPORATION www.vutec.com TEL: (954)-545-9006 FAX: (954)-545-9011 02/20/08 – 06/10 Rev. D 2-INSTL_D EMAIL: info@vutec.com...
Need help?
Do you have a question about the Lectric 4 and is the answer not in the manual?
Questions and answers