Wolfgang Warmbier METRISO 2000 Operating Instructions Manual

Wolfgang Warmbier METRISO 2000 Operating Instructions Manual

Esd test instrument
Table of Contents

Advertisement

Operating Instructions
â
METRISO
2000 – ESD Test Instrument
3-349-087-53
High-Resistance Tester for the Measurement of Resistance to Ground and Surface Resistance
4/8.01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the METRISO 2000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Wolfgang Warmbier METRISO 2000

  • Page 1 Operating Instructions â METRISO 2000 – ESD Test Instrument 3-349-087-53 High-Resistance Tester for the Measurement of Resistance to Ground and Surface Resistance 4/8.01...
  • Page 2 Toggle Switch Measurement Middle switch contact: jack, COM Starts measurement Left switch contact: Right switch contact: Socket for external charger Displays basic functions, Displays basic functions, Part No. 7100.2000.MK.Z501D scrolling from right to left scrolling from left to right WOLFGANG WARMBIER...
  • Page 3: Table Of Contents

    Measurement Value Display ................8 12.3 Changing the Batteries of the Temperature and Humidity Measuring Online Help .....................8 Adapter Z541A ..................... 22 ESD Measurement ................9 12.4 Housing ....................... 22 Condensed Instructions ...................9 5.1.1 Setting Limit Values – LIMIT Function ...............9 WOLFGANG WARMBIER...
  • Page 4: Applications

    (part no. 7100.2000.MK.Z501D) â METRISO 2000: • Resistance to ground, surface and volume resistance (with special measuring probes) • Insulation resistance (with variable and rising measurement voltage) • Temperature and relative humidity (with included, special sensor) • Voltage and frequency WOLFGANG WARMBIER...
  • Page 5: Initial Start-Up

    Press the or the key in order to display the desired measuring The instrument may not be operated if the battery compartment function, the device settings or the database functions. cover has not been installed and properly tightened! WOLFGANG WARMBIER...
  • Page 6 The last used settings remain when the instrument is switched ➭ Press the key to quit the setup menue. ➭ Press the key to quit the setup menue. The instrument can be switched off manually by simultaneously activating the two outermost softkeys. WOLFGANG WARMBIER...
  • Page 7 Contrast can be optimized with the two keys at the far right. ➭ Press the START key to quit the setup menue. The data are saved to ➭ Press the START key to quit the setup menue. The data are saved to memory. memory. WOLFGANG WARMBIER...
  • Page 8: General Operation

    Press any key to exit the help function. Mains measurement inputs (resistance measurements are disabled) – Measured resistance exceeds the selected limit value. LIMIT A voltage of greater than 25 V is present at the measurement U>25V inputs. WOLFGANG WARMBIER...
  • Page 9: Esd Measurement

    Press the START key briefly to perform a single, one-time measurement. If measurement needs to be performed over a longer period of time, the START key must be pressed and held for the desired test duration. WOLFGANG WARMBIER...
  • Page 10: Measuring Resistance To Ground R E

    Test Voltage according to IEC 61340-5-1 / DIN EN 61340-5-1: in W (open-circuit voltage) Test Voltage in W £ 10 £ 10 V (open-circuit voltage) £ 10 < R 100 V £ 10 £ 10 V £ 10 < R 100 V WOLFGANG WARMBIER...
  • Page 11: Measuring Surface Resistance

    Connect the “GUARD terminal” at the ring probe to the GUARD jack â at the METRISO 2000. ➭ Select the R menu and a test voltage of U = 10 V. If a value of less than 100 k W is displayed, the measured value is the result. WOLFGANG WARMBIER...
  • Page 12: Measuring Volume Resistance R V

    100 volts. The value then displayed is the result. chapters. Test Voltage according to IEC 61340-5-1 / DIN EN 61340-5-1: Test Voltage in W (open-circuit voltage) £ 10 £ 10 V £ 10 < R 100 V WOLFGANG WARMBIER...
  • Page 13: Database Functions

    After the ¿ softkey has been activated once again, a designation for the selected test object can be entered. ☞ Note These entries are required by the PC software in order to enter measurement values into the database, and to generate reports with this information automatically. WOLFGANG WARMBIER...
  • Page 14: Saving Measurement Values - Store Function

    START key (press at center) . The following message appears: “Data are stored”. In case a measurement value is missing for the currently selected location, perform the measurement and the value will be immediately stored. START WOLFGANG WARMBIER...
  • Page 15: Deleting A Data Record From Within A Memory Address - View Function

    After all of these fields have been entirely overwritten with blanks,they are displayed as inverse images. START ➭ Acknowledge with the START key (press at center). All data from the selected memory address are deleted. WOLFGANG WARMBIER...
  • Page 16: Delete All Memory Addresses - Data Function

    If the above message appears upon switching on the test instrument, all data can be saved to a PC before finally deleting the database in order to button START (press at center) a safety request appears. rectify the error. WOLFGANG WARMBIER...
  • Page 17: Measuring Insulation Resistance

    (when the desired voltage is displayed) or • As soon as a measurable test current is detected START (e.g. after a discharge voltage sparkover). Test voltage, any response and discharge voltage values and insulation resistance are all displayed. WOLFGANG WARMBIER...
  • Page 18: Measuring Alternating Voltage

    Then push the adapter down to fix it tightly. WOLFGANG WARMBIER...
  • Page 19: Characteristic Values

    4 ea. 1.5 V baby cells (4 x C-Size) on-time and performance of one measurement (alkaline-manganese per IEC LR14) before each automatic instrument shutdown or 4 ea. NiCd rechargeable batteries For U~/f and T/F 5 hours (same conditions as above) WOLFGANG WARMBIER...
  • Page 20 Nominal Temperature –10 ... +50 ° C Operating Temperature –20 ... +60 ° C (without batteries) Storage Temperature Relative Humidity to 75% (max. 85% for storage and transport), no condensation allowed Elevation max. 2000 m Deployment indoors only WOLFGANG WARMBIER...
  • Page 21: List Of Abbreviations And Their Meanings

    LED: The U, LIMIT and NETZ/MAINS lamps each blink twice in red. The PE lamp cannot be tested automatically! As soon as the tests in the left-hand column have been completed, the following tests must be started manually: WOLFGANG WARMBIER...
  • Page 22: Battery Operation

    – Rechargeable batteries have been installed (not normal batteries). – The instrument has been disconnected from the measuring circuit at all poles. – The voltage selector at the charger has been set to 9 V. WOLFGANG WARMBIER...
  • Page 23 WOLFGANG WARMBIER...
  • Page 24 Printed in Germany · Subject to change without notice WOLFGANG WARMBIER Untere Gießwiesen 21 78247 Hilzingen, Germany Phone: +49 77 31 86 88-0 Fax: +49 77 31 86 88-30 e-mail: info@warmbier.com http://www.warmbier.com...

Table of Contents

Save PDF