Subscribe to Our Youtube Channel
Related Manuals for Vislink HDT-1000S2
Summary of Contents for Vislink HDT-1000S2
- Page 1 HDT-1000S2 Compact HD/SD Digital Video Transmitter User and Technical Manual Manual Part No. RD000079 Rev.1 January 2011 Preliminary Draft - April 2010...
- Page 2 The foregoing does not apply to vendor proprietary parts. Vislink has made every effort to ensure the accuracy of the material contained in this manual at the time of printing. As specifications, equipment, and this manual are subject to change without notice, Vislink assumes no responsibility or liability whatsoever for any errors or inaccuracies that may appear in this manual or for any decisions based on its use.
- Page 3 The HDT-1000S2 is designed to transmit up to two NTSC (or PAL) standard definition (SD) video signals or one high-definition (HD) video signal (up to 1080i) plus two audio signals and an RS-232 data channel.
- Page 4 DB-9M connector. Video Input Video is input to the HDT-1000S2 through the front panel BNC connector. The HDT-1000S2 accepts an NTSC or PAL analog composite signal, as well as an ASI, or HD-SDI digital video signal. You select between analog or digital video input using the web server software.
-
Page 5: Applying Power
(such as a dish antenna) and never look into the open end of a waveguide or cable where RF power may be present. The HDT-1000S2 is a mobile transmitter. This unit, operated without an antenna, will not create RF energy exceeding 1.0 mW/cm , the FCC limit for exposure. - Page 6 6. Multiply R² * 4π 7. [S] Divide (R² * 4π) into EIRP S = Power Density in milliwatts per square centimeters. Note At frequencies above 1500 MHz, S must not be greater than 1. Rev 1 HDT-1000S2 User and Technical...
- Page 7 Vislink, in accordance with the requirements set forth by the FCC, provides this information as a guide to the user. It is assumed that the users of this equipment are licensed and qualified to operate the equipment per the guidelines and recommendations contained within the product user guides and in accordance with any FCC rules that may apply.
- Page 8 Select from 16 factory or custom preset configurations • Configure and save up to 16 custom preset configurations • Load custom preset configurations from a file on your PC into your HDT-1000S2. • Apply an encryption key to the presets simultaneously or individually. AUDIO 1...
- Page 9 Selecting a Preset The HDT-1000S2 recalls the most recently saved preset when it is powered up. To select a preset, do the following: 1. Press the PRESET key. The currently selected preset LED flashes.
- Page 10 Selecting the RF Output Level The HDT-1000S2 recalls the most recently saved RF output power level when it is powered up. To select between high or low power for the RF output level, do the following: 1.
- Page 11 Addressing Alarms LEDs illuminate when a fault is detected during normal operation of the HDT-1000S2. The following table shows a list of faults and what to do when they appear. Indicator Meaning Suggested Technical Staff Action RF HI Illuminates to indicate that the RF Power Select the power level required to is set to HI.
- Page 12 Using a PC to Control the HDT-1000S2 To set up your HDT-1000S2 with a PC, do the following: 1. Connect a LAN cable to the network connection of a router or switch and the ethernet port on the HDT-1000S2. 2. Open a web browser and type 192.168.4.150 into the URL address field and press Enter.
- Page 13 Apply. 6. Select Encryption Settings from the Radio drop down menu. The Encryption Settings screen appears. Note For 128-bit encryption, enter 32 hexadecimal characters. For 256-bit encryption, enter 64 hexadecimal characters. HDT-1000S2 User and Technical Rev 1 1-11...
- Page 14 2. Select the preset number and click Load. The relevant parameters will be populated under Video and Radio. Note The Encryption code will not display. Click Logout to finish setting up the HDT-1000S2. Rev 1 1-12 HDT-1000S2 User and Technical...
- Page 15 HDT-1000S2 Specifications The following figure shows a top and end views of the HDT-1000S2. 4.125” 10.48 cm 3.925” .675” 9.97 cm 1.71 cm 2.87” 7.29 cm 2.67” 6.8 cm RF OUT Connector The RF TNC female connector attaches the antenna to the unit.
-
Page 16: Ethernet Connector
RS232 TXD - Control RS232 TXD - Data DC Power Connection The following table shows the pin-outs for the Lemo (FGGOB304CLAD52) POWER IN 4-pin connector. Vislink supplies a DC power cable assembly with each unit. male power Connector Description +11—+32 Vdc +11—+32 Vdc... - Page 17 Model number and serial number of the unit (located on a label on the bottom of each unit). • Approximate purchase date. There are no supported field repairs or replacement parts for the HDT-1000S2 system. Return the unit for factory repair. CAUTION If you attempt field repair, you risk damaging your equipment. If your equipment is under warranty, you may also affect your warranty coverage.
- Page 18 Rev 1 1-16 HDT-1000S2 User and Technical...
Need help?
Do you have a question about the HDT-1000S2 and is the answer not in the manual?
Questions and answers