Related Manuals for Velodyne WiC-10
Summary of Contents for Velodyne WiC-10
- Page 1 U S E R ’ S M A N U A L Wi-Connect Wireless Subwoofer WiC-10...
-
Page 2: Table Of Contents
W i-Connect User’s Manual SAFETY NOTICES ..................1 SET UP Place Subwoofer. -
Page 3: Safety Notices
W i-Connect User’s Manual SAFETY NOTICES CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - Page 4 W i-Connect User’s Manual 12. POWER-CORD PROTECTION — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the product.
-
Page 5: Set Up
W i-Connect User’s Manual SET UP Place Subwoofer 1. Before you remove the subwoofer from the box, place the box near where you want to place the subwoofer in your room. If you’ve already unpacked the subwoofer, move the subwoofer to where you want it in the room. See diagram below. Follow these general guides: •... -
Page 6: Placement Cautions
W i-Connect User’s Manual Make sure: • You can get to the connections on the rear of the subwoofer • The included 6’ power cord for the subwoofer can safely reach a power outlet • The audio cable supplied by you can reach from the subwoofer to the audio system receiver outputs. Later you can fine tune the location of your subwoofer for your listening preferences, move the subwoofer to different spots and listen to the audio output until you determine the location you want for the subwoofer. - Page 7 W i-Connect User’s Manual Wireless Transmitter --------- REDRAW PER VELODYNETRANSMITTER INPUTS -------- Transmitter inputs drawing here 1. INPUT L and R: Inputs for connecting to the receiver’s RCA outputs. INPUT LFE: Input for connecting to the receiver’s LFE output. 2. CHANNEL: Selection switch for choosing broadcast frequency. This CHANNEL selection must match the CHANNEL selection on the subwoofer.
- Page 8 W i-Connect User’s Manual Subwoofer Cabinet Back --------- REDRAW PER VELODYNE CONNECTIONS and CONTROLS -------- Transmitter inputs drawing here 1. VOLUME: Adjust subwoofer volume. 2. ACTIVE: Green when ON/ACTIVE and red when ON/STANDBY. Goes to STANDY if no audio signal for 8 minutes.
-
Page 9: Connect Wireless Transmitter
W i-Connect User’s Manual Connect Wireless Transmitter 1. Use the included RCA cable to connect the wireless transmitter’s LFE input to your receiver’s LFE or SUB output or the wireless transmitter’s L and R inputs to your receiver’s L and R outputs. 2. -
Page 10: Select Receiver Options For Optimal Subwoofer Performance
W i-Connect User’s Manual No Receiver inputs drawing here SETUP #2: MOST COMMON with NO RECEIVER LFE/SUB OUTPUT Select Receiver Options for Optimal Subwoofer Performance It is important that the audio system’s existing receiver is set up correctly to work in concert with the subwoofer. To set up the receiver refer to its instruction manual and: If the receiver has a subwoofer or LFE output and you want to use it as the input to your subwoofer (most common case): NOTE:... -
Page 11: Connect Subwoofer
W i-Connect User’s Manual 3. Select the speaker size as LARGE. 4. If the crossover frequency option is available, double your main speakers specified low frequency response value and select the result as the crossover frequency. If you don’t know the low frequency response value, use 80 Hz. 5. -
Page 12: Adjust Subwoofer Controls
W i-Connect User’s Manual Adjust Subwoofer Controls Now it’s time to adjust the subwoofer controls to match your listening environment and preferences. 1. Turn the VOLUME to a level that balances with the output volume of your satellite speakers and doesn’t distort the bass sounds. You might also want to adjust your receiver’s LFE output volume higher, if you can’t get a loud enough subwoofer output, or lower, if the subwoofer output is too loud. -
Page 13: Use The Subwoofer's Lfe Input (Optional)
W i-Connect User’s Manual Use the Subwoofer’s LFE Input (Optional) In case you misplace the wireless transmitter or the wireless transmitter malfunctions, you can also connect the subwoofer to your receiver with an RCA cable. To connect this way: NOTE: Do not use the LFE connection option if you are already using the wireless connection option. -
Page 14: Features
W i-Connect User’s Manual FEATURES Protection Circuitry The subwoofer is equipped with protection circuitry to provide maximum performance with greatest reliability. The subwoofer is protected against: • Overdriving the speaker • Overdriving the amplifier • Overheating the amplifier • Excessive drop in power line voltage The overdrive protection circuitry operates constantly without being audible under most situations. -
Page 15: Troubleshoot
Save the carton and packing materials for future use. Using other packaging for this unit may result in severe damage when shipping or moving. You can use this packaging should you ever move or need to return the subwoofer to Velodyne for service. To save storage space, you can flatten the box and put the other packing material in a plastic bag. -
Page 16: Service
W i-Connect User’s Manual Service DO NOT ATTEMPT TO SERVICE THE SUBWOOFER OR WIRELESS TRANSMITTER YOURSELF beyond what is described in this owner’s manual. ONLY USE QUALIFIED SERVICE TECHNICIANS TO REPAIR DAMAGED PARTS. Service the subwoofer or transmitter using qualified service technicians when: •... -
Page 17: Regulatory Information
W i-Connect User’s Manual RESOURCES Regulatory Information FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 18: Radio Frequency Exposure Requirements
For further information, contact your local waste disposal service, your local city government office, or the retailer where you purchased this subwoofer. Trademarks The Velodyne logo is a registered trademark of Velodyne Acoustics, Inc. [ 1 ]... -
Page 19: Warranty
LIMITED WARRANTY - U.S. AND CANADA ONLY VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warrants all electronics for a period of three years, drivers for a period of five years, and full range speakers for a period of five years. All VELODYNE products have a warranty from the date of purchase against defects in materials and... - Page 20 Velodyne Acoustics, Inc. 345 Digital Drive Morgan Hill, CA 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 service fax www.velodyne.com Service E-mail: service@velodyne.com Product E-mail: help@velodyne.com Technical E-mail: techhelp@velodyne.com 63-WiCON Rev A JUL10...
Need help?
Do you have a question about the WiC-10 and is the answer not in the manual?
Questions and answers