Maintenance - Toshiba RAS-H10BACVS-V Owner's Manual

2 PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press .
3. Insert the batteries.
3 AIR FLOW DIRECTION
FIX
Press : Move the louver in
1
the desired vertical direction.
SWING
Press : Swing the air
2
automatically and press again to stop.
For horizontal direction, adjust
3
manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
4
REMOTE CONTROL
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 Off timer button (OFF)
9 High power button (Hi-POWER)
! Economy button (ECO)
" Clear button (CLEAR)
# Check button (CHECK)
5 AUTOMATIC OPERATION
To automatically select cooling or fan only operation
MODE
1. Press : Select A.
2. Press : Set the desired temperature.
FAN
3. Press : Select AUTO, LOW , LOW+
MED+ , or HIGH
6
COOLING / FAN ONLY OPERATION
MODE
1. Press : Select Cool
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
FAN
3. Press : Select AUTO, LOW , LOW+
MED+ , or HIGH
1110255132_EN.indd 3 1110255132_EN.indd 3
1
3 4
2
6
7
5
9
!
8
"
#
, MED ,
.
or Fan only .
, MED ,
.
7 DRY OPERATION
For dehumidifi cation, a moderate cooling performance is controlled automatically.
MODE
1. Press : Select Dry .
2. Press : Set the desired temperature.
8 Hi-POWER OPERATION
To automatically control room temperature and airfl ow for faster cooling
operation (except in DRY and FAN ONLY mode)
Hi POWER
Press : Start and stop the operation.
9 ECO OPERATION
To automatically control room to save energy (except in DRY and FAN ONLY mode)
Press : Start and stop the operation.
Note: Cooling operation; the set temperature will increase automatically 1
degree/hour for 2 hours (maximum 2 degrees increase).
10 TEMPORARY OPERATION
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C and fan
operation is automatic speed.
11 TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting the OFF timer
1
OFF
Press for enter OFF timer setting.
2
Press for select desired OFF timer. (0.5 - 12 hrs)
3
OFF
Press for set OFF timer.
4
OFF
Press again for cancel OFF timer.
12 AUTO RESTART OPERATION
To automatically restart the air conditioner after the power failure (Power of
the unit must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for
5 seconds)
2. Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
• In case of ON timer or OFF timer are set, AUTO RESTART
OPERATION does not activate.
13

MAINTENANCE

Firstly, turn off the circuit breaker.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when
needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
EN
CT
3/2/2559 BE 16:35 3/2/2559 BE 16:35