PRODUCT AND HAVE VERIFIED THAT ALL COMPONENTS ARE FUNCTIONING PROPERLY. (IF DAMAGE IS EVIDENT, CONTACT THE FREIGHT CARRIER OR WINCO IMMEDIATELY!) Winco assumes no responsibility for damage or injury caused by the improper assembly, installation, use or maintenance of these products.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to an authorized Winco service center. 5. DO NOT carry or pull this product by power supply cord or use the cord as a handle.
Page 4
No adapter should be used with this product. For an added level of safety; Winco recommends the use of a 120 volt GFCI (ground fault circuit interruptor) outlet.
ASSEMBLY INSTRUCTIONS BACK ASSEMBLY INSTRUCTIONS BACK ASSEMBLY INSTRUCTIONS 1. Remove back assembly and chair frame from carton. 1. Remove back assembly and chair frame from carton. NOTE: Heat Only and Heat & Massage chairs, AVOID disconnecting any "chair to back" wires. NOTE: Heat Only and Heat &...
OPERATING INSTRUCTIONS RECLINING THE CARE CLINER ALL CHAIRS HAVE 3 STANDARD POSITIONS PLUS INFINITE POSITIONING THRU TRENDELENBERG* WHEN GAS SPRING IS ENGAGED FROM 3rd RECLINE POSITION) 1. From the #1 (SEATED UPRIGHT) position, grip the arm rests and simultaneously lean body weight back.
Page 7
NOTE: Periodically lubricate the channels of the drop arms with your approved silicone base lubricant spray to keep the parts moving freely. DO NOT raise & lower Drop-Arms with tables in an FIG. 5 upright position. (Drop-Arm Care Cliner Models ONLY)
Page 8
& clear washers (FIG.2) when cleaning or maintenance of chair is complete. DROP-ARM VINYL PANEL (For Drop-Arm Care Cliner Models ONLY) 1. The vinyl panel is secured to the bottom of the Drop- Arm with a hook & loop fastener material. Peel hook &...
OPERATING INSTRUCTIONS (FIG.1) TO POSITION SIDE TABLES 1. To raise table, grasp center of table and gently raise into place. Table will automatically lock into place when released. 2. To lower table, grasp table at the center, raise and pivot down in one movement. (FIG.2) VERSA-TABLE “Lap"...
GENERAL MAINTENANCE ADJUSTING GAS SPRING NOTE: Tension or "ease of movement" of the gas spring is set by factory and cannot be changed. The following instruction is for adjusting the gas spring "release and engagement points" for Trendelenburg or "deep recline" positions only. 1.
Recline Mechanism with a silicone based Please refer to the PERMABLOK lubricant. instruction tag that is attached to your Care Cliner for complete care and cleaning instructions. Once per week, position the Chair Back into full recline position, squeeze release handle Retain information on tag for future use.
Back Width ......22” Seat Depth......19.5” Overall Height ......47” Weight .......95 lbs. Maximum Weight Capacity..275 lbs. 6940-6950 SWING-ARM CARE CLINER (6940 shown) NOTE: 6530-1/6550-1/6700/6900/6940 Model Chairs have one Gas Spring. 6540-1/6570-1/6910/6950 (XL) Model Chairs have two Gas Springs. Overall Width ....6940=33.5”...
AND connection of power cord to power pack unit under chair. • If switch displays a flashing light; Check all accessible wire connectors under chair for possible loose connections, then contact Winco customer service: 1-800-237-3377. CORD STORAGE (Models with Heat or Massage only) 1.
OPTIONS FOR YOUR WINCO CARE CLINER Heat & Massage IV Pole & Attachment Leg Extensions HM ........Heat & Massage IV........ IV Pole & Attachment Leg Extensions raises chair 3" HT ..........Heat ONLY AVAILABLE FOR ALL MODELS RE00.........Round Leg Extension SE00.........Square Leg Extension AVAILABLE FOR ALL MODELS RE00 for models........653#, 654#...
TERMS Winco Mfg., LLC. warrants this product to be free of manufacturer’s defects in material and workmanship, provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer. This warranty is available only to the original retail purchaser, is non-transferable and commences on the date of retail sale;...