Advertisement
Quick Links
For Technical assitance, please contact :
Canadian customers should return to:
Infinition Inc.
2455 de l'Industrie
Trois-Rivieres (QC) Canada
G8Z 4T1
techsupport@mylabradar.com
316-866-2525
LabRadar
User Manual
Certification : Under approval
All others should return to:
TCK, LLC
8221 W. Meadow Pass Ct
Wichita, KS 67205
U.S.A.
techsupport@mylabradar.com
316-866-2525
Advertisement
Summary of Contents for Infinition Labradar
- Page 1 LabRadar User Manual Certification : Under approval For Technical assitance, please contact : Canadian customers should return to: All others should return to: Infinition Inc. TCK, LLC 2455 de l’Industrie 8221 W. Meadow Pass Ct Trois-Rivieres (QC) Canada Wichita, KS 67205 G8Z 4T1 U.S.A.
- Page 2 The LabRadar must be operated either by 6 AA batteries or by plugging the USB cord to a computer’s USB port. Do not allow any objects to rest on the USB cord or place the LabRadar where the USB cord will be trampled on.
- Page 3 LabRadar is positioned besides the shooter, not downrange. The shooter aligns the radar using a built-in sighting notch with the target he intends to shoot. Ideally, LabRadar should be positioned to the side of the shooter’s muzzle. You should position your firearm no greater than 18” from the side of the radar. If you are...
- Page 4 Unit is powered On, transmitting, system will stop transmitting shortly (within 10 seconds) if no trigger is detected. 4.1 Buttons definition The LabRadar is equipped with an array of buttons each used for a different function: 1. Display / Parameters 2. Series 3.
- Page 5 gram (g); grain (gr). Select vel. range Select the velocity range for measurements by the LabRadar. Each velocity range is specified to weapons type as a reference: Rifle (300m/s to 1050m/s); Handgun (75m/s to 525m/s);...
- Page 6 Select the frequency of transmission of the Radar. In order to use multiple radars close to each other, use a different frequency for each radar. Failure to do so may result in bad operation of the radar. For contiguous Labradar, try to use at least a 2 channels separation.
- Page 7 4.3 Using the LabRadar Turn on LabRadar by pressing the Power Button. You will see a blue light to indicate the unit is on. 4.3.1 ALIGNING THE RADAR Locate a suitable position for your LabRadar and position it within 18 inches to either side of the muzzle of your firearm.
- Page 8 4.3.3 Last shot review mode (Blue indicator) If the system is armed and is then disarmed (either manually or automatically), the indicator turns blue and the Last shot is displayed on screen as show here: Infinition Inc. Rev. 02...
- Page 9 4.3.5 Review Mode (Blue indicator) The review mode allows the user to navigate through all the results available in the LabRadar. When it it turned ON, the LabRadar starts in Review mode. To access the Review mode from the Last shot review or the Armed view, the user should hold the arm button for 2 seconds.
- Page 10 LabRadar as a Mass Storage Device and display the files available on the SD Card. Alternatively, the user can turn OFF the LabRadar and remove the SD card to read it in a memory card reader (Fastest).
- Page 11 Each shot is recorded in the sequence that it was fired in. The Series and Shots can be reviewed on LabRadar or on a PC at a later time. LabRadar provides the ability to record up to 1,000 shots in 1,000 different series.
- Page 12 Average: The average Velocity of all shots in the current Series. 5. Maintenance The LabRadar radar does not require much maintenance. Attention should however be paid to a few points: Keep the connectors clean from dirt and moisture to avoid corrosion and bad connections.
- Page 13 9. Range The LabRadar is a consumer level device that was designed for amateur use only. The performance of the units has been optimized to offer the most accurate results, but it is possible that some reading are not accurate, hence it is the responsibility of the user to determine whether or not the readings are good or not to its satisfaction.
- Page 14 10. Firmware upgrade The LabRadar’s firmware can be upgraded to the latest version at any time. Please check our website to check availability. In order to upgrade your firmware: 1. Download the latest version on our website; 2. Copy the file on the LabRadar’s SD Card root (1 or 2 files);...
- Page 15 CONSULT WITH PROPER GOVERNMENT AUTHORITIES BEFORE EXPORTING or IMPORTING THIS ITEM. Infinition Inc. Rev. 02...
- Page 16 The Labradar will turn OFF and back ON when armed : Check the batteries level. The Labradar will not power ON: Check the batteries, replace if needed. / Check the USB connection, if power supply is powered on. Press the Power Button.