HPE FlexFabric 12900E Configuration Manual
  1. Manuals
  2. Brands
  3. HPE Manuals
  4. Switch
  5. FlexFabric 12900E
  6. Configuration manual

HPE FlexFabric 12900E Configuration Manual

Hide thumbs Also See for FlexFabric 12900E:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual
HPE FlexFabric 12900E & 12900
SPB

Configuration Guide

Part number: 5998-8715R
Software version: Release 1135 and later
Document version: 6W102-20151124

Advertisement

Table of Contents
loading

Related Manuals for HPE FlexFabric 12900E

Summary of Contents for HPE FlexFabric 12900E

  • Page 1: Configuration Guide

    HPE FlexFabric 12900E & 12900 Configuration Guide Part number: 5998-8715R Software version: Release 1135 and later Document version: 6W102-20151124...
  • Page 2 © Copyright 2015 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Contents SPBM overview ······························································································· 1     SPBM network model ········································································································································ 1   Terminology ······················································································································································· 1   AC ······························································································································································ 1   Area ···························································································································································· 1   BCB ···························································································································································· 2   BEB ···························································································································································· 2   B-MAC, B-VLAN ········································································································································· 2   Customer network port, provider network port ··························································································· 2  ...
  • Page 4   Tuning the SPF calculation timer ············································································································· 25   Setting the LSDB overload bit ·················································································································· 26   Configuring the control MAC address for ISIS-SPB ················································································· 26   Configuring ISIS-SPB authentication ··············································································································· 27   Configuring ISIS-SPB adjacency authentication ······················································································ 27   Configuring ISIS-SPB area authentication ·······························································································...

  • Page 5: Spbm Overview

    SPBM overview IEEE 802.1aq Shortest Path Bridging (SPB) enables multipath routing in an Ethernet mesh network by using IS-IS as the control protocol. The technology allows all paths to be active, supports equal cost paths, and provides shortest path forwarding in an Ethernet mesh network. IEEE 802.1aq SPB provides faster convergence, higher link efficiency, and larger Layer 2 topologies than conventional spanning tree protocols such as MSTP.

  • Page 6: Bcb

    Backbone core bridges (BCBs) are core nodes of an SPBM network. BCBs forward MAC-in-MAC frames based on the B-MAC and B-VLAN. They do not learn customer MAC (C-MAC) addresses. Backbone edge bridges (BEBs) are edge nodes of the SPBM network. BEBs encapsulate customer frames into MAC-in-MAC frames before forwarding them to the SPBM network.

  • Page 7: Spb Vsi

    Pseudo wires (PWs) are MAC-in-MAC tunnels established over the SPBM network for transmitting customer traffic. PWs are established between BEBs. BCBs do not set up PWs. On an interface, incoming frames are assigned to the same PW if they match the frame match criterion of the same Ethernet service instance.

  • Page 8: Working Mechanisms

    Figure 2 IEEE 802.1ah-compliant MAC-in-MAC frame format Table 1 IEEE 802.1ah encapsulated frame header fields Field Description B-DA Destination B-MAC that identifies the destination BEB. Source B-MAC. It is a known MAC address of the BEB that encapsulates the B-SA MAC-in-MAC frame.

  • Page 9: Formation And Maintenance Of Isis-Spb Adjacencies

    Formation and maintenance of ISIS-SPB adjacencies ISIS-SPB only supports point-to-point links within an IS-IS level 1. It sends P2P hellos between directly connected nodes to form and maintain adjacencies. To forward traffic on an adjacency, two SPBM neighbors must meet the following requirements: •...
  • Page 10 Figure 3 MAC-in-MAC unicast traffic over an SPBM network Multicast SPBM floods broadcast, customer multicast, and unknown customer unicast as multicast traffic. SPBM supports the following replication methods for multicast: • Head-end replication—Replicates frames at the ingress BEB for frames to enter the SPBM network.
  • Page 11 Figure 4 Head-end replication Customer network Data B-MAC B-VLAN Port BEB1 FGE1/0/1 BEB 3 BEB2 FGE1/0/2 BEB3 FGE1/0/3 B-MAC B-VLAN Port BEB2 FGE1/0/1 B-MAC B-VLAN Port BEB3 FGE1/0/1 BEB1 FGE1/0/1 BEB2 FGE1/0/1 B-DA B-SA B-VLAN I-SID Data BEB3 BEB1 BEB 1 FGE1/0/1 FGE1/0/1 B-MAC...

  • Page 12: Spbm Multicast Address

    Figure 5 Tandem replication Customer network Data B-MAC B-VLAN Port M-BEB1 FGE1/0/2，FGE1/0/3 M-BEB2 FGE1/0/1，FGE1/0/3 BEB 3 M-BEB3 FGE1/0/1，FGE1/0/2 B-MAC B-VLAN Port M-BEB3 FGE1/0/1 B-DA B-SA B-VLAN I-SID Data M-BEB1 BEB1 BEB 1 FGE 1/0/1 FGE 1/0/1 B-MAC B-VLAN Port Data M-BEB2 FGE1/0/1 B-MAC...

  • Page 13: Multiple Spb Vsis

    Field Description 1-bit local flag bit. Its value is fixed at 1. 2-bit SPSource ID type. Its value is fixed at 0. SPSource ID 20-bit SPSource ID. I-SID 24-bit SPB VSI identifier. Figure 6, LSB represents the lower 4 bits of a byte, and MSB represents the higher 4 bits of a byte. The first byte of an SPBM multicast address is identical to the combination of the first 4 bits of the SPSource ID field, the TYP field, the L field, and the M field.

  • Page 14: Load Balancing

    Load balancing To balance traffic between forwarding paths, you can map B-VLANs to different ECT algorithms. When a path is approaching congestion, you can move part of traffic on one path to another by moving an I-SID from one ECT algorithm to another. B-VLAN to ECT algorithm mapping For balanced traffic distribution, SPBM supports calculating one SPT for a set of B-VLANs by using different ECT algorithms.

  • Page 15: Loop Prevention

    Figure 9 ECT migration BCB 1 B-VLAN 300 ECT 1 Path A (ECT 1) BEB 2 BEB 1 Customer Customer SPBM network network network I-SID 400 B-VLAN 300 I-SID 400 B-VLAN 300 B-VLAN 300 ECT 1 B-VLAN 300 ECT 1 Path B (ECT 2) B-VLAN 300 ECT 2...

  • Page 16: Configuring Spbm

    Configuring SPBM Feature and software version compatibility The SPBM feature is available in Release 1137 and later versions. Configuration restrictions and guidelines When you use SPBM in conjunction with other features, follow the restrictions and guidelines Table Table 3 SPBM and other features compatibility Feature Restrictions and guidelines You must configure the irf mac-address persistent always command to...
  • Page 17 Tasks at a glance Remarks Configure customer-side settings to map (Required.) Configuring customer-side settings on BEBs: Ethernet service instances to SPB VSIs • Enabling L2VPN for extending C-VLANs across different • Creating an SPB VSI sites. • Assigning a B-VLAN to an SPB VSI Each Ethernet service instance •...

  • Page 18: Configuring Basic Spbm Settings On Bebs And Bcbs

    Configuring basic SPBM settings on BEBs and BCBs For SPBM to run, you must configure all settings in this section on all BEBs and BCBs. Configuring MST region parameters CAUTION: Changing MST region settings causes spanning tree recalculation. Make sure you understand the impact on your network before you activate the MST region settings.

  • Page 19: Configuring Customer-Side Settings On Bebs

    To enable SPBM: Step Command Remarks Enter system view. system-view Enable SPBM globally and By default, SPBM is disabled spbm enter SPBM view. globally. Return to system view. quit Enter Layer 2 Ethernet interface interface-type interface view or Layer 2 interface-number aggregate interface view.

  • Page 20: Assigning A B-Vlan To An Spb Vsi

    To create an SPB VSI: Step Command Remarks Enter system view. system-view Create a VSI. vsi vsi-name By default, no VSIs exist. Assign an SPB I-SID to spb i-sid i-sid By default, a VSI does not have an SPB I-SID. the VSI.

  • Page 21: Configuring Spbm Multicast Settings

    Step Command Remarks • Access link type: port access vlan vlan-id • Trunk link type: port trunk permit vlan Assign the port to C-VLANs. { vlan-id-list | all } • Hybrid link type: port hybrid vlan vlan-id-list { tagged | untagged } Create an Ethernet service By default, no Ethernet service service-instance instance-id...

  • Page 22: Optimizing Traffic Distribution

    Step Command Remarks Enter system view. system-view Enter SPBM view. spbm By default, the device generates Set SPSource ID. spsource spsource-id an SPSource ID automatically. Optimizing traffic distribution Setting the bridge priority In conjunction with the system ID, the SPBM bridge priority forms the SPBM bridge ID. The SPBM bridge ID is a tie-breaker used in the ECT algorithms for choosing the forwarding path.

  • Page 23: Mapping B-Vlans To An Ect Algorithm

    Step Command Remarks Enter SPBM view. spbm Set a global SPBM link By default, no global SPBM link circuit-cost cost-value metric value. metric value is set. Setting the bandwidth reference for automatic link metric calculation ISIS-SPB automatically calculates a link metric value for an interface if both the global and interface-specific link metric value are not set.
  • Page 24 • Using ECT migration, you can move traffic by I-SID without traffic loss. To perform ECT migration: On all BEBs and BCBs, create a new B-VLAN, assign the B-VLAN to MSTI 4092, and assign the provider network port to the B-VLAN: Step Command Remarks...

  • Page 25: Configuring The Ap Mode

    Assign the new B-VLAN to the SPB VSI on all BEBs: Step Command Enter VSI view. vsi vsi-name Enter SPB I-SID view. spb i-sid i-sid Assign the new B-VLAN to the SPB VSI. b-vlan vlan-id NOTE: The SPB VSI's traffic will not be switched over to the new path until you assign the new B-VLAN to the SPB VSI on all BEBs.

  • Page 26: Tuning Isis-Spb Adjacency Maintenance Settings

    Step Command Remarks Enter system view. system-view Enter SPBM view. spbm By default, dynamic hostname exchange Configure a symbolic is-name is-name is disabled, and no symbolic hostname is hostname. configured for the device. Tuning ISIS-SPB adjacency maintenance settings ISIS-SPB uses the ISIS-SPB hello interval and the hello multiplier for adjacency establishment and maintenance.

  • Page 27: Tuning Isis-Spb Lsp Timers

    Step Command Remarks The default multiplier is 3. The maximum adjacency hold spbm timer holding-multiplier time is 65535 seconds. If this Set the hello multiplier. value value is exceeded, the original hello multiplier remains unchanged. Tuning ISIS-SPB LSP timers Change LSP timer settings depending on network stability to increase the network convergence speed and protect CPU from unnecessary route recalculations.
  • Page 28 NOTE: ISIS-SPB requires acknowledgment for each LSP sent on a point-to-point circuit. ISIS-SPB will retransmit an LSP at 5-second interval until it receives an acknowledgment for the LSP. This retransmission interval is not user configurable. Setting the LSP lifetime The LSP lifetime specifies the maximum amount of time for an LSP to be retained in an LSDB. SPBM nodes add a lifetime in each LSP they have advertised.

  • Page 29: Tuning The Spf Calculation Timer

    Step Command Remarks Enter system view. system-view Enter SPBM view. spbm The default refresh interval is 900 Set the LSP refresh interval. timer lsp-refresh seconds seconds. Default values for the LSP generation timer parameters: • maximum-interval—2 seconds. • minimum-interval—10 timer lsp-generation Set the LSP generation timer milliseconds.

  • Page 30: Setting The Lsdb Overload Bit

    NOTE: The network is considered unstable if the interval between consecutive SPF calculations is smaller than two times the maximum wait time. To tune the SPF calculation timer: Step Command Remarks Enter system view. system-view Enter SPBM view. spbm Default values for the SPF calculation timer parameters: •...

  • Page 31: Configuring Isis-Spb Authentication

    Step Command Remarks The default control MAC for Configure the control MAC control-address { all-cb | all-is | ISIS-SPB is 0180-C200-002E for ISIS-SPB. all-l1-is | all-l2-is | all-pb } (all-pb). Configuring ISIS-SPB authentication ISIS-SPB authentication helps improve security in an SPBM network. It includes adjacency authentication and area authentication.

  • Page 32: Configuring Graceful Restart For Isis-Spb

    advertisement packet only if the authentication settings in the packet match their local authentication settings. For correct authentication, make sure the authentication method and password is the same across the SPBM network. To prevent temporary drops of topology advertisement packets, use the following procedure when you modify authentication settings: Disable area authentication for incoming ISIS-SPB topology advertisement packets on the neighbor devices.

  • Page 33: Configuring Snmp Notifications For Spbm

    Step Command Remarks By default, the Suppress-Advertisement (SA) bit is set. Setting the SA bit prevents the neighbor from advertising the ISIS-SPB adjacency with the (Optional.) Set the SA GR restarter. This setting prevents route undo graceful-restart bit in ISIS-SPB hello blackholes by temporarily excluding the suppress-sa PDUs.

  • Page 34: Displaying And Maintaining Spbm

    Displaying and maintaining SPBM Execute display commands in any view and reset commands in user view. Task Command Display MAC-in-MAC connections. display l2vpn minm connection [ vsi vsi-name ] display l2vpn minm forwarding [ vsi vsi-name ] [ slot Display MAC-in-MAC forwarding entries (in standalone mode).
  • Page 35 Task Command Display SPBM multicast FIB entries (in display spbm multicast-fib [ mac-address mac-address standalone mode). [ b-vlan vlan-id ] | b-vlan vlan-id ] [ slot slot-number ] [ verbose ] display spbm multicast-fib [ mac-address mac-address Display SPBM multicast FIB entries (in [ b-vlan vlan-id ] | b-vlan vlan-id ] [ chassis chassis-number slot IRF mode).

  • Page 36: Spbm Configuration Examples

    Task Command Clear SPBM unicast FIB statistics (in reset spbm unicast-fib statistics slot slot-number standalone mode). Clear SPBM unicast FIB statistics (in reset spbm unicast-fib statistics chassis chassis-number slot IRF mode). slot-number SPBM configuration examples Basic SPBM configuration example Network requirements Deploy an SPBM network as shown in Figure Use I-SID 1000 to extend VLAN 100 across customer sites 1, 2, and 3.
  • Page 37 # Create C-VLAN 100 and B-VLAN 10. <BEB1> system-view [BEB1] vlan 100 [BEB1-vlan100] quit [BEB1] vlan 10 [BEB1-vlan10] quit # Configure MST region parameters on BEB 1. Make sure B-VLAN 10 is mapped to MSTI 4092. [BEB1] stp region-configuration [BEB1-mst-region] region-name spbm [BEB1-mst-region] instance 4092 vlan 10 [BEB1-mst-region] active region-configuration [BEB1-mst-region] quit...
  • Page 38 [BEB1-vsi-test-1000] multicast replicate-mode tandem [BEB1-vsi-test-1000] quit [BEB1-vsi-test] quit # Create Ethernet service instance 1, assign C-VLAN 100 to this instance, and map the service instance to the SPB VSI. [BEB1] interface fortygige 1/0/2 [BEB1-FortyGigE1/0/2] port link-type trunk [BEB1-FortyGigE1/0/2] port trunk permit vlan 100 [BEB1-FortyGigE1/0/2] service-instance 1 [BEB1-FortyGigE1/0/2-srv1] encapsulation s-vid 100 [BEB1-FortyGigE1/0/2-srv1] xconnect vsi test...
  • Page 39 0011.2200.1201.00-01 0x00000003 0x7e23 1186 0011.2200.1301.00-00 0x00000002 0xc9e 1186 0011.2200.1301.00-01 0x00000003 0x7a21 1186 0011.2200.1401.00-00 0x00000002 0xa23b 1190 0011.2200.1401.00-01 0x00000003 0xdfb6 1190 0011.2200.1501.00-00 0x00000002 0xa23b 1190 0011.2200.1501.00-01 0x00000003 0xdfb6 1190 # Verify that the BEB has unicast PWs to all other BEBs. <BEB1>...

  • Page 40: Spbm With Head-End Replication Configuration Example

    LSP ID Seq Num Checksum Holdtime Length Overload ------------------------------------------------------------------------------- 0011.2200.1101.00-00 0x00000002 0x7bf8 1180 0011.2200.1101.00-01 0x00000003 0xe7c8 1180 0011.2200.1201.00-00 0x00000002 0xa9e 1186 0011.2200.1201.00-01 0x00000003 0x7e23 1186 0011.2200.1301.00-00 0x00000002 0xc9e 1186 0011.2200.1301.00-01 0x00000003 0x7a21 1186 0011.2200.1401.00-00* 0x00000002 0xa23b 1190 0011.2200.1401.00-01* 0x00000003 0xdfb6 1190 0011.2200.1501.00-00 0x00000002...
  • Page 41 Figure 11 Network diagram Configuration procedure Configure BEB 1: # Create C-VLAN 100 and B-VLAN 3001. <BEB1> system-view [BEB1] vlan 100 [BEB1-vlan100] quit [BEB1] vlan 3001 [BEB1-vlan3001] quit # Configure MST region parameters on BEB 1. Make sure B-VLAN 3001 is mapped to MSTI 4092.
  • Page 42 # Assign B-VLAN 3001 to the SPB VSI. [BEB1-vsi-test-3001] b-vlan 3001 [BEB1-vsi-test-3001] quit [BEB1-vsi-test] quit # Assign the customer network port FortyGigE 1/0/1 to C-VLAN 100. [BEB1] interface fortygige 1/0/1 [BEB1-FortyGigE1/0/1] port link-type trunk [BEB1-FortyGigE1/0/1] port trunk permit vlan 100 # Configure Ethernet service instance 1 to match C-VLAN 100, and map the service instance to the SPB VSI.

  • Page 43: Spbm With Tandem Replication Configuration Example

    ------------------------- System ID Port Circuit ID State Holdtime 0000.eeee.0101 FGE1/0/2 Verify that the BEB has established tunnels to other BEBs. [BEB1] display l2vpn vsi name test verbose VSI Name: test VSI Index VSI State : Up : 1500 Bandwidth : 102400 kbps Broadcast Restrain : 5% Multicast Restrain...
  • Page 44 Figure 12 Network diagram Configuration procedure Configure BEB 1: # Create C-VLAN 100 and B-VLAN 3001. <BEB1> system-view [BEB1] vlan 100 [BEB1-vlan100] quit [BEB1] vlan 3001 [BEB1-vlan3001] quit # Configure MST region parameters on BEB 1. Make sure B-VLAN 3001 is mapped to MSTI 4092.
  • Page 45 # Assign B-VLAN 3001 to the SPB VSI. [BEB1-vsi-test-3001] b-vlan 3001 # Enable tandem multicast replication for the SPB VSI. [BEB1-vsi-test-3001] multicast replicate-mode tandem [BEB1-vsi-test-3001] quit [BEB1-vsi-test] quit # Assign the customer network port FortyGigE 1/0/1 to C-VLAN 100. [BEB1] interface fortygige 1/0/1 [BEB1-FortyGigE1/0/1] port link-type trunk [BEB1-FortyGigE1/0/1] port trunk permit vlan 100 # Configure Ethernet service instance 1 to match C-VLAN 100, and map the service instance to...

  • Page 46: Ect Migration By Changing B-Vlan Example

    [BEB1] display spbm peer Peer information for SPBM ------------------------- System ID Port Circuit ID State Holdtime 0000.eeee.0101 FGE1/0/2 Verify that the BEB has established tunnels to other BEBs. [BEB1] display l2vpn vsi name test verbose VSI Name: test VSI Index VSI State : Up : 1500...
  • Page 47 Figure 13 Network diagram Configuration procedure Configure BEB 1: # Create C-VLAN 100, B-VLAN 3001, and B-VLAN 3003. <BEB1> system-view [BEB1] vlan 100 [BEB1-vlan100] quit [BEB1] vlan 3001 [BEB1-vlan3001] quit [BEB1] vlan 3003 [BEB1-vlan3003] quit # Configure MST region parameters on BEB 1. Make sure B-VLAN 3001 and B-VLAN 3003 are mapped to MSTI 4092.
  • Page 48 # Enable SPBM on the provider network ports on BEB 1. Assign the provider network ports to B-VLAN 3001 and B-VLAN 3003. [BEB1] interface fortygige 3/0/2 [BEB1-FortyGigE3/0/2] port link-type trunk [BEB1-FortyGigE3/0/2] port trunk permit vlan 3001 3003 [BEB1-FortyGigE3/0/2] spbm enable [BEB1-FortyGigE3/0/2] quit [BEB1] interface fortygige 3/0/3 [BEB1-FortyGigE3/0/3] port link-type trunk...
  • Page 49 # Enable SPBM globally. [BCB1] spbm # Map B-VLAN 3003 to ECT algorithm 9. [BCB1-spbm] ect 9 b-vlan 3003 [BCB1-spbm] quit # Enable SPBM on the provider network ports on BCB 1. Assign the provider network ports to B-VLAN 3001 and B-VLAN 3003. [BCB1] interface fortygige 1/0/1 [BCB1-FortyGigE1/0/1] port link-type trunk [BCB1-FortyGigE1/0/1] port trunk permit vlan 3001 3003...

  • Page 50: Ect Migration By Changing Ect Algorithm Example

    Drop Unknown SPB I-SID : 3001 SPB Connections: BMAC BVLAN Link ID Type 0000-9999-0141 3001 Unicast ACs: Link ID State FGE3/0/1 srv1 # Verify that I-SID 3001 uses B-VLAN 3001 to transmit customer traffic. [BEB1] display spbm ect-migration i-sid 3001 B-VLAN 00-80-c2-01 3001...
  • Page 51 Configuration procedure This example uses BEB 1 to show the configuration procedure. You can configure other SPBM devices in the same way you configure BEB 1. Configure the new B-VLAN (VLAN 20 in this example): Perform this task on all BEBs and BCBs in the SPBM network. # Create VLAN 20.
  • Page 52 0011.2200.1201 1000 0011-2200-1201 FGE1/0/1 FGE1/0/3 0011.2200.1301 1000 0011-2200-1301 FGE1/0/1 FGE1/0/3 # Verify that the BEB still uses the original multicast PW established on B-VLAN 10 for I-SID 1000. <BEB1> display spbm multicast-pw System ID I-SID MAC address B-VLAN Port 0011.2200.1101 1000 0306-4000-03e8 FGE1/0/1...
  • Page 53 0011.2200.1501 0011-2200-1501 FGE1/0/3 # Verify that the BCB has created multicast FDB entries in both B-VLANs 10 and 20 for I-SID 1000. <BCB1> display spbm multicast-fdb Flags: E-Egress T-Transit System ID MAC address B-VLAN Flags Port 0011.2200.1101 0306-4000-03e8 FGE1/0/2 FGE1/0/3 0011.2200.1101 0306-4000-03e8 FGE1/0/2...
  • Page 54 0011.2200.1501 0011-2200-1501 FGE1/0/3 0011.2200.1501 0011-2200-1501 FGE1/0/3 # Verify that the BEB has multicast FDB entries only in B-VLAN 20. <BEB1> display spbm multicast-fdb Flags: E-Egress T-Transit System ID MAC address B-VLAN Flags Port 0011.2200.1101 0306-4000-03e8 FGE1/0/3 0011.2200.1201 0306-4001-03e8 0011.2200.1301 0306-4002-03e8 On BCBs (BCB 1 in this example): # Verify that the BCB has unicast FDB entries in both B-VLANs 10 and 20 for I-SID 1000.

  • Page 55: Document Conventions And Icons

    Document conventions and icons Conventions This section describes the conventions used in the documentation. Port numbering in examples The port numbers in this document are for illustration only and might be unavailable on your device. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown.

  • Page 56: Network Topology Icons

    Network topology icons Convention Description Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.

  • Page 57: Support And Other Resources

    Support and other resources Accessing Hewlett Packard Enterprise Support • For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website: www.hpe.com/assistance • To access documentation and support services, go to the Hewlett Packard Enterprise Support Center website: www.hpe.com/support/hpesc Information to collect •...

  • Page 58: Websites

    Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (docsfeedback@hpe.com). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page.

  • Page 59: Index

    Index SPBM edge bridge network model, 1 Numerics SPBM backbone core bridge, 2 SPBM 802.1ah data packet, 3 SPBM basic configuration, 14, 32 SPBM ISIS-SPB hello packet, 3 SPBM configuration, 12, 12, 32 SPBM ISIS-SPB LSP, 3 SPBM ISIS-SPB SNP, 3 Ethernet service instances, 16 SPBM overview, 1 SPBM backbone edge bridge, 2...
  • Page 60 SPBM hello multiplier for calculating adjacency displaying hold time, 22 SPBM, 30 SPBM SPF calculation timer, 25 dynamic SPBM dynamic hostname exchange, 21 changing SPBM ISIS-SPB adjacency change logging, 29 channel SPBM fast channel LSP propagation, 11 SPBM bridge priority, 18 compatibility SPBM B-VLAN >...
  • Page 61 SPBM BEB Ethernet service instances, 16 SPBM ISIS-SPB LSP timer, 23 SPBM LSP fast-flooding, 25 interval SPBM LSP refresh interval, 24 SPBM LSP generation timer, 24 SPBM LSP transmit interval min, 23 SPBM LSP lifetime, 24 SPBM LSP refresh interval, 24 I-SID SPBM backbone service identifier, 2 SPBM LSP transmit interval min, 23...
  • Page 62 SPBM AP mode, 21 assigning SPBM SPB VSI B-VLAN, 16 SPBM basic configuration, 14, 32 configuring SPBM, 12, 12 SPBM BEB customer-side setting configuring SPBM (head-end replication), 36 configuration, 15 configuring SPBM (tandem replication), 39 SPBM configuration (head-end replication), 36 configuring SPBM AP mode, 21 SPBM configuration (tandem replication), 39 configuring SPBM bandwidth reference for...
  • Page 63 setting SPBM PNP link metric value (global), 18 SPBM, 3 setting SPBM PNP link metric value SPBM (port-specific), 18 AP mode configuration, 21 setting SPBM SPSource ID, 17 area, 1 tuning SPBM ISIS-SPB adjacency attachment circuit, 1 maintenance, 22 backbone core bridge (BCB), 2 tuning SPBM ISIS-SPB LSP timer, 23 backbone edge bridge (BEB), 2 tuning SPBM LSP generation timer, 24...
  • Page 64 ISIS-SPB control MAC address, 26 SPBM LSP generation timer, 24 ISIS-SPB control packet, 3 SPBM SPF calculation, 25 ISIS-SPB hello interval, 22 traffic SPBM multiple SPB VSIs, 9 ISIS-SPB hello packet, 3 SPBM traffic distribution optimization, 18 ISIS-SPB LSP, 3 ISIS-SPB LSP timer, 23 transmitting SPBM fast channel LSP propagation, 11...

This manual is also suitable for:

Flexfabric 12900

Table of Contents