Connecting A Vcr And Cable Box - Philips 55PW9383 Directions For Use Manual

P resented here is a connection example
involving a VCR and cable box.
Refer to the VCR's directions-for-use manual
for further information on connections.
To make the connections in this example, you
will need:
• one, two-way signal splitter
• two coaxial cables (75Ω)
• one cable for a video connection (standard
RCA connector)
• two cables for audio connections (standard
RCA connectors) (only one cable is needed
for connection to a nonstereo VCR).
NOTE: The cables are not supplied with your
TV. You should be able to buy them at most
stores that sell electronics. Or you can call
our Customer Care Center at
1-800-531-0039.
1
Connect a cable TV signal to a two-
way signal splitter.
2
Connect one of the two-way signal
splitter outputs to the INPUT on the
cable box.
3
Connect the other two-way signal
splitter output to the ANTENNA IN
75Ω on the rear of the TV.
4
Connect from the cable box OUTPUT
jack to the ANT IN jack on the rear of
the VCR.
5
Connect the VIDEO OUT jack on
the VCR to the INPUT-AV 1 VIDEO
jack on the rear of the TV.
6
Connect the AUDIO OUT R(ight)
and L(eft) jacks on the VCR to
INPUT-AV 1 AUDIO jacks on the rear
of the TV.
NOTE: If the VCR is a nonstereo unit,
connect only the left audio cable,
which usually has a white connector.
7
Press the AV button on the remote
control as many times as necessary
to select the AV1 source for the view-
ing of materials from your VCR.
C
ONNECTING A
Rear of VCR*
* (Example: Philips
VCR model
VR674CAT)
AV1
7
VCR C
AND ABLE
3
ANTENNA IN 75Ω
+
CENTER CHANNEL AMP INPUT
5
INPUT-AV 1
VIDEO
S-VIDEO
L
L
AUDIO
R
POWER
TV VCR ACC
ACTIVE
SWAP PIP CH CONTROL FREEZE
DN UP
PICTURE
SOUND
MENU/
STATUS/
SELECT
EXIT
MUTE
VOL CH
1 2 3
4 5 6
7 8 9
TV/VCR
0
A/CH
SURF
SURF PIP ON/OFF
REC • FORMAT SLEEP
SAP
AV DOLBY V PROG.LIST
ITR/ HOME HOME PERSONAL
9
Connecting Accessory Devices to Your TV
B
OX
Rear of TV
AMP SWITCH
EXT INT
_
HD INPUT-AV 5
DVI
HD INPUT-AV 4
G/Y
6
R/Pr
OUTPUT INPUT-AV 2 SUBWOOFER
Y
B/Pb
VIDEO
S-VIDEO
L
Pb
V
L L
SYNC
AUDIO AUDIO
Pr
H
R
R
Two-way
Signal
Splitter
INPUT
1
Coaxial Cable Lead-in from
Cable TV Company
or VHF/UHF Antenna
H
ELPFUL
• The RF output on a cable box, usually
labeled "OUTPUT," "OUT," or "TO TV,"
will not pass a stereo sound signal to the
ANTENNA IN 75Ω jack on the TV. If, how-
ever, your cable box has separate
Audio/Video outputs, using A/V cables to
connect to those outputs and to the A/V
inputs on the TV might pass a stereo sound
signal to the TV. Contact your cable TV
company for more information.
• To simplify making connections, the plugs
on audio and video cables are often color
coded. The jacks on your TV are likewise
color coded to match the plugs.
The coding is as follows:
—Yellow for video (composite)
—Red for the right audio channel
—White for the left audio channel
NOTE: If your VCR is mono (nonstereo),
you will connect only one audio cable. You
must ensure that the TV is set to MONO for
the signal source to which you've connected
the VCR (INPUT-AV 2, INPUT-AV 1, or the
side panel inputs [AV3]). Otherwise, you will
receive sound from only one of the TV's
speakers. See page 38.
L
AUDIO
R
4
AUDIO
L
ANT
IN
OUT IN
R
VIDEO
OUT
IN
OUT CH3 CH4
Rear of Cable Box
OUTPUT
2
H
INTS