Table of Contents
Advertisement
Quick Links
Signal Booster
Installation
Guide
Direct Connect
Signal Boosters
Contents:
How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-Vehicle Wilson Installation
Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Lightning Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . 6
In-Building Wilson Installation
Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Powering Up a Wilson Signal Booster . . . . . . . . . . . . . . . . 8
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . 9
Guarantee and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
Note: This manual contains important safety and operating information .
Please read and follow the instructions in this manual . Failure to do
so could be hazardous and result in damage to your Signal Booster .
Wilson
®
Electronics, Inc.
Advertisement
Table of Contents
Related Manuals for Wilson Electronics 2B1401
Summary of Contents for Wilson Electronics 2B1401
-
Page 1: Table Of Contents
Signal Booster Installation Guide Direct Connect Signal Boosters Contents: How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before Getting Started . -
Page 2: How It Works
Installation Instructions for the Following Wilson Electronics Signal Boosters Direct Connect 800/1900 MHz with GPS amplification – Model # 2B1401 FCC ID: PWO2B1401SA IC: 4726A-2B1401SA The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. -
Page 3: Before Getting Started
E911 emergency location feature if your phone is so equipped. In emergencies, E911 enabled phones provide caller location to 911 call centers. Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST. - Page 4 The antenna cable is small enough to easily tuck under the door seal or plastic molding . Tuck Cable Under Seal NOTE: See RF Safety Warnings (p. 9) Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
- Page 5 Supply until the Outside Antenna and external adapter cables are attached to the Signal Booster . Cell Phone DC Power Supply Adapter Signal Booster Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
-
Page 6: Adapter
“Inside Antenna” on the Signal Booster . NOTE: Depending on your specific cell phone, the adapter socket may be located beneath a rubber plug. Figure 1 Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST. -
Page 7: Lightning Surge Protection
Ensure the LSP is properly grounded. (For RG6 Ground Wire cable use #859988-75 Ohm, For 50 Ohm use Part #859902) . Lightning Surge Protection To the Signal Booster Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST. - Page 8 (sold separately) to the power input labeled “12V DC” on the Signal Booster . Recommended installation locations for in-building are: • On a wall • On the ceiling • Near a power outlet Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com Hours: 7am to 6pm MST.
-
Page 9: Powering Up A Wilson Signal Booster
. You should see a signal improvement of 2 or more bars . Note: Many phones take up to 20 seconds to reset the bar indicator. Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com... -
Page 10: Warnings And Recommendations
Booster in a location with adequate ventilation, such as under the seat, in the trunk or under the dashboard. Keep the area free of items that could block air flow to the Signal Booster. Contact Wilson Electronics Tech Support with any questions at 866-294-1660 Or email: tech@wilsonelectronics.com... - Page 11 (RMA) number supplied by Wilson Electronics . Wilson Electronics shall, at its option, either repair or replace the product . Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer, if located within the continental U .S .
-
Page 12: Signal Booster Specifications
Signal Booster Specifications Dual-Band 800/1900 MHz Specifications Model Number / Part Number 2B1401 / 811207, 811209 Connectors FME-Male Impedance (input/output) 50 ohms Dimensions 5 x 5 .4 x 1 .4 inch or 14 x 10 .8 x 3 .5 cm Weight 1 .32 lbs or 0 .6 kg...