Advertisement
Quick Links
Advertisement
Related Manuals for APart-Audio REVAMP4240T
Summary of Contents for APart-Audio REVAMP4240T
- Page 1 REVAMP4240T Instruction manual...
- Page 3 REVAMP4240T Instruction manual REVAMP4240T Manual...
-
Page 4: Important Safety Instructions
CLASS-D POWER AMPLIFIER IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions This professional device needs to be installed by qualified personnel only. Danger: Exposure to high sound levels may cause a permanent hearing loss. - Page 5 REVAMP4240T Instruction manual 15. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 16. Do not defeat the safety purpose of the polarised or grounding plug. A polarised plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong.
- Page 6 CLASS-D POWER AMPLIFIER 24. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. - Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside.
- Page 7 REVAMP4240T Instruction manual Features • 2 rack units high • High power Hypex® class-D power amplifier modules • Bridgeable 4-channel class-D amplifier • RMS output power: 4 x 220 W @ 100 V • Bridged output power: 2 x 480 W @ 100 V •...
- Page 8 CLASS-D POWER AMPLIFIER Connections 11 12 Only channel 1 and 2 are explained. Channel 3 and 4 are functionally identical to 1 and 2. 1. Channel 2 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the amplifier from shutting down.
- Page 9 REVAMP4240T Instruction manual 4. Channel 1 unbalanced input and link cinch connector: connect the line level input signal for channel 1 here. Line level is 0 dBV. Input and link connector are internally connected 1 on 1. This connector is also used in bridge mode.
-
Page 10: Operation
CLASS-D POWER AMPLIFIER 14. Mains voltage inlet: connect the mains power cord here. Operation 1. Removable rack ears for 19 rack mounting. 2. Power switch. 3. Power led. 4. Channel 1 and 2 mute buttons and multifunctional led display. 5. Channel 3 and 4 mute buttons and multifunctional led display. - Page 11 REVAMP4240T Instruction manual • Clip – overload led indicates that the amplifier is overloaded or clipping: reduce the incoming signal immediately to avoid overloads or clipping and eventually amplifier shutdown. • Limit – muted indicates that the internal limiter is active or that the channel is muted by pushing the mute button.
- Page 12 CLASS-D POWER AMPLIFIER !!! IMPORTANT !!! This amplifier relies on convectional and active cooling. In normal situations, overheating will not occur. The unit can be built in a 19 inch rack system, but it is forbidden to block the ventilation holes provided.
- Page 13 REVAMP4240T Instruction manual 110 VAC operation: it is possible to operate the unit at 110 (115) VAC. Therefore, open the unit and set a wire jumper on the connector for 110 VAC operation.
-
Page 14: Technical Specifications
CLASS-D POWER AMPLIFIER Technical specifications output power 4 x 240 W / 100 volt load impedance 42 ohms / 100 volts; 21 ohms / 70 volts; 10.5 ohms / 50 volts; 5.1 ohms / 35 volts; 4 ohms / 4 ohms input connections 4 x unbalanced on RCA with passthrough + 4 x balanced on... - Page 16 Audioprof nv Industriepark Brechtsebaan 8 bus 1 2900 Schoten - Belgium Company names, product names and trademarks are property of their respective owners. Apart-Audio specifications are subject to change without notice.