The user manual applies to the following device types: IMP5212 The images of IMP5212 adopted in the following descriptions. Any of the different specifications between the device types are elaborated. Before reading the manual, please confirm the device type.
The IMP5212 Video Wall Processor and its inner control software compose the Video Wall system, the device integrates an internal control software to connect to and configure the controller. You can configure multi-screen and multi-presets with the input video sources, and set them at any position and in arbitrary size in the operating interface of the software.
Page 8
Product Overview IMP5212 Video Wall Processor supports the following features: Features Supports up to 26 windows displayed through a single output channel, with image zoom, overlay, roaming, and cross-screen displayed. Supports up to 12 screens to be grouped together as the monitor wall.
Page 9
Supports several control methods: RS232 control, color touch screen and remote control computer(TCP/IP) Provides a color touch screen in front panel for touch control Application example Figure 1-2 The example for IMP5212 Application...
Safety Chapter 2 Safety FCC Caution Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 12
Safety Warnings: Read, keep and follow all of these instructions for your safety. Heed all warnings. Video Wall Processor Upgrading of the device is subject to change without notice. Contact your Customer Service representative if parts are missing or damaged.
When unpacking the components of this switcher, please verify that none of the components listed in Table 3-1 are damaged or lack. If there is any missing, contact your distributors or Beijing Osee Digital Technology Ltd. for it. Table 3-1 Packing List...
Page 14
Installation The IMP5212 video wall processor has already been assembled according to the customer's requirements. You can follow the instructions below to replace the corresponding module when need to replace or expand your processor.
Page 15
Unpack and Installation Ensure that all handling precautions are taken to avoid electrostatic discharge or other damage to sensitive electronic components. Wear an earth strap and perform all PCB assembly at an appropriate anti-static work station. Follow the instructions carefully to fit the modules. Replace the module Follow the following steps to replace a module: At first, check the frame.
Page 16
Unpack and Installation Swivel Handle Figure 3-3 The Swivel Handle of the Power Module Step 1 Remove the old module Take an input module for example, loosen the screws, as shown in Figure 3-4, and then pull out the module along the slot of the frame, as shown in Figure 3-5.
Page 17
Unpack and Installation Step 2 Replace a new module Then, push the new module slightly along the slot, press module again to confirm that the module is installed firmly and then fasten the screws. Please make sure the module type and the slot position must be matched with each other.
IMP5212 Features Chapter 4 IMP5212 Features This chapter describes the features of IMP5212. 4.1 Front Panel Features There are four indicators in the center of the front panel, as shown in Figure 4.1-1 Figure 4.1-1 the Buttons in Front Panel 1.
IMP5212 Features There are two groups of fans positioned at the top and bottom of the frame. Please check the fans' status when the case temperature alarm happens. The fans support hot swap. PS1 Indicator It is used to indicate the PS1 power on or off. If the light is green, the device is powered on, and if the light is off, the device is powered off.
Page 21
Figure 4.1-3 Selecting a Preset Up to 50 presets can be preview, and the touch screen provides the former 20 presets for fast switching operation. Refer to the manual for OSEE Video Wall System control software for the details about the preset definition.
Page 22
GPO Control interface, and the indicator of the screen will turn green when it is turned on. In IMP5212, GPO control is realized through the GPO interface of its control module. The GPO interface connect the video wall processor and the display screens with its four groups of inner low voltage relays, thus to control open or close of the connected devices.
Page 23
启 动 启 动 mode is started up. IMP5212 will open the No.1~No.4 screen according to these GPO delay time. Figure 4.1-6 Set the Delay Time for GPO Control The No.1 screen will open at once for its GPO1 is 0 second, and The No.2 screen will open at 2 second, then is the No.3 screen, opens at 4 second,...
Page 24
IMP5212 Features the same time without delay. For example: take up the example, all of the No.1~No.4 screens turn off at 9 second the time you clicked the stop button. The timing sequence logic is as shown in Figure 4.1-8:...
It will introduce the arrangement and the operations of the interfaces in rear of the panel in the following. As shown in Figure 4.2-1, IMP5212 provides the various connectors for power supply, input, output and control, the details are as below:...
Page 26
MODULES MODULES MODULE Figure 4.2-1 The Rear Connector of IMP5212 The video wall processor performs the power supply, input, output and control functions through the corresponding modules, and you should make sure the module has been inserted to the correct slot in the frame. Facing at the...
IMP5212 Features 4.2.1 Bus Board IMP5212 uses the bus board to integrate input module, output module and control module, and the modules should be positioned into slots differently according to the module types, then the transmission between them will be normal.
Page 28
IMP5212 Features Figure 4.2-3 Input Module (Side View) Panel for Input Module Figure 4.2-4 Panel for Input Module (Front View) After insert the input module into the corresponding slot, and put the panel onto the interfaces of the input module, fasten the screws to fix the module...
Page 29
IMP5212 Features Figure 4.2-5 Installation of an Input Module into the Frame The input module provides 2 channels of DVI-M input interfaces (the input signal is adaptive), the physical diagram is shown in Figure 4.2-6: Figure 4.2-6 Image for Input Module ...
Page 30
640X480, 800X600, 1024X768, 1280X720, 1280X768, Input formats 1280X800, 1280X1024, 1360X768, 1366X768, 1400X1050, 1440X900, 1600X1200, 1680X1050, 1920X1080, It supports up to 13 input modules in one IMP5212 frame. Input Adaptor There are three kinds of input adaptor for the various input signals:...
Page 31
IMP5212 Features DVI-M-3 Adaptor (YPbPr、S-Video、CVBS): the image for this adaptor is as shown in Figure 4.2-8. Make sure the composited Video interface is corresponding to the input signal type, the relationship is as shown in the table below: Interface Color\Signal Type...
IMP5212 Features 4.2.3 Output Module IMP5212 provides an output module. Each output module supports three DVI outputs. The output module is cooperated with its matched output module panel, as shown in Figure 4.2-11: Output Module Figure 4.2-11 Output Module (Side View) ...
IMP5212 Features module and its panel. The output module provides 3 channels of DVI OUT outputs, with DVI-D interface, the physical diagram is shown in Figure 4.2-13: Figure 4.2-13 Image for Output Module Table 4-3 The Resolutions of the DVI Interfaces...
Page 34
IMP5212 Features Figure 4.2-15 Panel for Control Module (Front View) The physical diagram for the Control Module is as shown in Figure 4.2-16: Figure 4.2-16 Image for Control Module 1. Connectors in Control Module The labels of the interfaces on the control module are as shown in Table 4.2-4:...
Page 35
Use this interface to connect with other video devices to implement router control, and you should set the communication parameters in the OSEE Video Wall System software, click set button "Device Management" "Serial Port", the window is as shown in Figure...
Page 36
IMP5212 Features 4.2-18: Figure 4.2-18 Setting Values for RS232 Parameters The relationship of the pins of RS232 connector and its channel value is shown in Table 4.2-6. RS232 Figure 4.2-19 The Pins Sequence of RS232 Connector Table 4.2-6 The Relationship of RS232 and Channel Values Pin No.
Page 37
IMP5212 Features RS232-422 Figure 4.2-20 The Pins Sequence of RS232-422 Connector Table 4.2-7 The Relationship of RS232-422 and Channel Values Pin No. Channel Value Pin1 Pin 2 RS422Tx- Pin 3 RS422Rx+ Pin4 Pin5 Pin6 Pin7 RS422Tx+ Pin8 RS422Rx- Pin9 The function of the RS232-422 interface is determined by a dip switch on the control module, as shown in Figure 4.2-21:...
Figure 4.2-24 The Ethernet Interface 4.3 Device Connection Connect the signal sources with the input interfaces of IMP5212 using cables, and connect the display screens with the output interfaces of IMP5212 using cables. The arrangement of the input modules and the output modules fully...
The rules of the connection sequence between the output interfaces and display screens: For the slots of input module and output module in IMP5212 are changeless, so the priority of the slots must be from the smaller numbered slot to the bigger slot one by one, and without skip. The arrangement sequence instruction is: display screens are numbered right to left, top to bottom corresponding with the number of the output interface.
Figure 4.4-1: Figure 4.4-1 The Interface of OSEE Video Wall System Software Refer to "The Manual for the OSEE Video Wall System" for details. 4.5 Control Instruction Set Set the Screen ON/OFF Instructions Set the manual/automatic GPO* ON/OFF instructions.
Page 41
IMP5212 Features Switch Preset Instructions Use the following instruction to switch to the corresponding preset n. Command Instruction EB-A5-12-00-A4-00-00-00-00-00-00-00-00-00-00-0 Switch to No.1 Preset 0-00-00-00-00-00-00-A5-EB EB-A5-12-00-A4-00-01-00-00-00-00-00-00-00-00-0 Switch to No.2 Preset 0-00-00-00-00-00-00-A5-EB EB-A5-12-00-A4-00-02-00-00-00-00-00-00-00-00-0 Switch to No.3 Preset 0-00-00-00-00-00-00-A5-EB EB-A5-12-00-A4-00-03-00-00-00-00-00-00-00-00-0 Switch to No.4 Preset...
Control Speed 10/100Base-T Module Ethernet Protocol TCP/IP Serial Port Types RS232, RS232-422 Operation RS422 / remote control through RJ-45 port Interface Display Units Up to 12 displays Control OSEE Video Wall System Software Temperature: 0~70℃ Environment Humidity: 10%~90% No condensation...
Page 44
Weight(fully 7U, 30kg 442(L)×315(W)×310(H)mm 18 slots loaded) Power 300W Consumption Electrical 100-240VAC, 50-60Hz, two redundant power modules Characteristics 2. Product Outline The outline of IMP5212 is shown as in the following figures: Figure 5-1 Front View Figure 5-2 Back View...
Page 45
Specifications Figure 5-3 Side View Specifications are subject to change without notice. ------------------No Text Below------------------...
Page 46
FOR MORE INFORMATION PLEASE VISIT: http://www.osee-dig.com/ OSEE TECHNOLOGY CO., LTD. No.22 Building, No.68 zone, Beiqing Road, Haidian District, Beijing, China Tel: (+86) 010-62434168, Fax: (+86) 010-62434169 E-mail: sales@osee-dig.com...